Add driver support for a 2 port PCI IOC3-based serial card on Altix boxes:

This is a re-submission.  On the original submission I was asked to
organize the code so that the MIPS ioc3 ethernet and serial parts could be
used with this driver.  Stanislaw Skowronek was kind enough to provide the
shim layer for this - thanks Stanislaw.  This patch includes the shim layer
and the Altix PCI ioc3 serial driver.  The MIPS merged ioc3 ethernet and
serial support is forthcoming.
Signed-off-by: NPatrick Gefre <pfg@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Patch from Andrew Victor

This patch adds support to the 2.6 kernel series for the Atmel
AT91RM9200 processor.

This patch is the Serial driver.

This version uses the newly re-written GPL'ed hardware headers.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

EPXA10DB seems to be uncared for:
- the "PLD" code has never been merged
- no one has reported that this platform has been broken since
  at least 2.6.10
- interest seems to have dried up around March 2003.

Therefore, remove EPXA10DB support.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The offsets of the registers are in a different place, and
some parts cannot handle a full set of modem control signals.
Signed-off-by: NPantelis Antoniou <pantelis@embeddedalley.ocm>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Use platform device for the 16500 UARTs in the onboard
SuperIO controller.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add separate files for the different 8250 ISA-based serial boards.

Looking across all the various architectures, it seems reasonable that
we can key the availability of the configuration options for these
beasts to the bus-related symbols (iow, CONFIG_ISA).  We also standardise
the base baud/uart clock rate for these boards - I'm sure that isn't
architecture specific, but is solely dependent on the crystal fitted
on the board (which should be the same no matter what type of machine
its fitted into.)
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The SGI IOC4 I/O controller chip drivers are currently all configured by
CONFIG_BLK_DEV_SGIIOC4.  This is undesirable as not all IOC4 hardware features
are needed by all systems.

This patch adds two configuration variables, CONFIG_SGI_IOC4 for core IOC4
driver support (see patch 1/3 in this series for further explanation) and
CONFIG_SERIAL_SGI_IOC4 to independently enable serial port support.
Signed-off-by: NBrent Casavant <bcasavan@sgi.com>
Acked-by: NPat Gefre <pfg@sgi.com>
Acked-by: NJeremy Higdon <jeremy@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!