Certain kinds of hardware time stamping units in both MACs and PHYs have
the limitation that they can only time stamp PTP packets. Drivers for such
hardware are left with the task of correctly matching skbs to time stamps.
This patch adds a BPF that drivers can use to classify PTP packets when
needed.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.

Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a hook for transmit time stamps. The transmit hook
allows a software fallback for transmit time stamps, for MACs
lacking time stamping hardware. Using the hook will still require
adding an inline function call to each MAC driver.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Without the 8021q module loaded in the kernel, all 802.1p packets 
(VLAN 0 but QoS tagging) are silently discarded (as expected, as 
the protocol is not loaded).
 
- Without this patch in 8021q module, these packets are forwarded to 
the module, but they are discarded also if VLAN 0 is not configured,
which should not be the default behaviour, as VLAN 0 is not really
a VLANed packet but a 802.1p packet. Defining VLAN 0 makes it almost
impossible to communicate with mixed 802.1p and non 802.1p devices on
the same network due to arp table issues.

- Changed logic to skip vlan specific code in vlan_skb_recv if VLAN 
is 0 and we have not defined a VLAN with ID 0, but we accept the 
packet with the encapsulated proto and pass it later to netif_rx.

- In the vlan device event handler, added some logic to add VLAN 0 
to HW filter in devices that support it (this prevented any traffic
in VLAN 0 to reach the stack in e1000e with HW filter under 2.6.35,
and probably also with other HW filtered cards, so we fix it here).

- In the vlan unregister logic, prevent the elimination of VLAN 0 
in devices with HW filter.

- The default behaviour is to ignore the VLAN 0 tagging and accept
the packet as if it was not tagged, but we can still define a 
VLAN 0 if desired (so it is backwards compatible).
Signed-off-by: NPedro Garcia <pedro.netdev@dondevamos.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MAX_SOCK_ADDR is no longer used because commit 230b1839 "net: Use standard
structures for generic socket address structures." replaced
"char address[MAX_SOCK_ADDR];" with "struct sockaddr_storage address;".
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

probe_irq_off() returns the first irq found or if two irqs are found
then it returns the negative of the first irq found.  We can cast
dev->irq to an int so that the test for negative values works.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'gap' is unsigned, so this code is wrong:

    gap = -new_head;
    ...
    if (gap > 0) { ... }

Make 'gap' signed.

The semantic patch that finds this problem (many false-positive results):
(http://coccinelle.lip6.fr/)

// <smpl>
@ r1 @
identifier f;
@@
int f(...) { ... }

@@
identifier r1.f;
type T;
unsigned T x;
@@

*x = f(...)
 ...
*x > 0
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pci_get_domain_bus_and_slot: caller must decrement the
reference count by calling pci_dev_put().
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change initializes the state of link at the time when driver is
loaded. The ethtool output for 'link detected' and 'link speed'
is thus valid even before the interface is brought up.
Signed-off-by: NShreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use DMA API as PCI equivalents will be deprecated. This change also allow
to allocate with GFP_KERNEL in some places.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix SGE resource resource deallocation bug.  Forgot to increment the RXQ and
TXQ cursors in the loop ...
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A new bit map 'intrCtrl' is introduced in the DriverShared area. The 
driver should update VMXNET3_IC_DISABLE_ALL bit before writing IMR.
Signed-off-by: NRonghua Zang <ronghua@vmware.com>
Signed-off-by: NShreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix LRO feature update.
Signed-off-by: NShreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct comment stating sizeof(struct tcp_skb_cb) is 36 or 40, since its
44 bytes, since commit 951dbc8a ([IPV6]: Move nextheader offset
to the IP6CB).
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Version update
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: NRamkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update and correct maintainers information
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: NRamkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update copyright information to reflect the Exar purchase of Neterion
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: NRamkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NETIF_F_LLTX and it's usage of local transmit locks are depricated in
favor of using the netdev queue's transmit lock.  Remove the local
lock and all references to it, and use the netdev queue transmit lock
in the transmit completion handler.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRamkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix error in multicast flag check, add calls to restore the status of
multicast and promiscuous mode settings after change_mtu, and style
cleanups to shorten the function calls by using a temporary variable.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: NRamkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove queue_state references, as they are no longer necessary.

Also, The driver needs to start/stop the queue regardless of which type
of steering is enabled.  Remove checks for TX_MULTIQ_STEERING only and
start/stop for all steering types.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: NRamkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ipv6_skip_exthdr() can return error code that is below zero.
'offset' is unsigned, so it makes no sense.
ipv6_skip_exthdr() returns 'int' so we can painlessly change type of
offset to int.
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'count' is unsigned. It is initialized to zero, then it can be increased
multiple times, and finally it is used in such a way:

   >>>> count--;
   |
   |    /* clear timestamp and dma mappings for remaining portion of packet */
   |    while (count >= 0) {
   |            count--;
   |            ...
   ^
If count is zero here (so, it was never increased), we would have a very
long loop :)
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

platform_get_irq_byname() can return negative results, it is not seen to
unsigned irq. Make it signed.
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

platform_get_irq_byname() can return negative results, it is not seen to
unsigned irq. Make it signed.
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There were two methods isdn_gethex() and isdn_getnum() which are custom
implementations of strtoul(). Get rid of them in regard to
strict_strtoul() kernel's function.
Signed-off-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: gigaset307x-common@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this case we safe to use strict_strtoul().
Signed-off-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>