Hold host_set lock while finishing internal qc.
Signed-off-by: NTejun Heo <htejun@gmail.com>

ap->active_tag was cleared in ata_qc_free().  This left ap->active_tag
dangling after ata_qc_complete().  Spurious interrupts inbetween could
incorrectly access the qc.  Clear active_tag in ata_qc_complete().
This change is necessary for later EH changes.
Signed-off-by: NTejun Heo <htejun@gmail.com>

ata_bus_probe() doesn't clear dev->class after ->phy_reset().  This
can result in falsely enabled devices if probing fails.  Clear
dev->class to ATA_DEV_UNKNOWN after fetching it.
Signed-off-by: NTejun Heo <htejun@gmail.com>

Kill duplicate prototypes for ata_eh_qc_complete/retry() in libata.h.
Signed-off-by: NTejun Heo <htejun@gmail.com>

While moving ata_scsi_error() from LLDD sht to libata transportt,
EXPORT_SYMBOL_GPL() entry was left out.  Kill it.
Signed-off-by: NTejun Heo <htejun@gmail.com>

AHCI calls ata_dev_classify() even when no device is attached which
results in false class code.  Fix it.
Signed-off-by: NTejun Heo <htejun@gmail.com>

Rename ata_down_sata_spd_limit() and friends to sata_down_spd_limit()
and likewise for simplicity & consistency.
Signed-off-by: NTejun Heo <htejun@gmail.com>

Don't directly access &qc->tf when tf == &qc->tf.
Signed-off-by: NTejun Heo <htejun@gmail.com>

libata needs to invoke EH without scmd.  This patch adds
shost->host_eh_scheduled to implement such behavior.

Currently the only user of this feature is libata and no general
interface is defined.  This patch simply adds handling for
host_eh_scheduled where needed and exports scsi_eh_wakeup() to
modules.  The rest is upto libata.  This is the result of the
following discussion.

http://thread.gmane.org/gmane.linux.scsi/23853/focus=9760

In short, SCSI host is not supposed to know about exceptions unrelated
to specific device or command.  Such exceptions should be handled by
transport layer proper.  However, the distinction is not essential to
ATA and libata is planning to depart from SCSI, so, for the time
being, libata will be using SCSI EH to handle such exceptions.
Signed-off-by: NTejun Heo <htejun@gmail.com>

Introduce scsi_req_abort_cmd(struct scsi_cmnd *).
This function requests that SCSI Core start recovery for the
command by deleting the timer and adding the command to the eh
queue.  It can be called by either LLDDs or SCSI Core.  LLDDs who
implement their own error recovery MAY ignore the timeout event if
they generated scsi_req_abort_cmd.

First post:
http://marc.theaimsgroup.com/?l=linux-scsi&m=113833937421677&w=2Signed-off-by: NLuben Tuikov <ltuikov@yahoo.com>
Signed-off-by: NTejun Heo <htejun@gmail.com>

* master.kernel.org:/home/rmk/linux-2.6-mmc:
  [MMC] pxamci: fix data timeout calculation

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] nommu: trivial fixups for head-nommu.S and the Makefile
  [ARM] vfp: fix leak of VFP_NAN_FLAG into FPSCR
  [ARM] 3484/1: Correct AEABI CFLAGS for correct enum handling

Few of the notifier_chain_register() callers use __init in the definition
of notifier_call.  It is incorrect as the function definition should be
available after the initializations (they do not unregister them during
initializations).

This patch fixes all such usages to _not_ have the notifier_call __init
section.
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Few of the notifier_chain_register() callers use __devinitdata in the
definition of notifier_block data structure.  It is incorrect as the
data structure should be available after the initializations (they do
not unregister them during initializations).

This was leading to an oops when notifier_chain_register() call is
invoked for those callback chains after initialization.

This patch fixes all such usages to _not_ have the notifier_block data
structure in the init data section.
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch addresses a flaw in LSM, where there is no mediation of readv()
and writev() in for 32-bit compatible apps using a 64-bit kernel.

This bug was discovered and fixed initially in the native readv/writev
code [1], but was not fixed in the compat code.  Thanks to Al for spotting
this one.

  [1] http://lwn.net/Articles/154282/Signed-off-by: NJames Morris <jmorris@namei.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

All modifications of ->i_flags in inodes that might be visible to
somebody else must be under ->i_mutex.  That patch fixes ext3 ioctl()
setting S_APPEND and friends.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Switched to use of sys_pread64()/sys_pwrite64() rather than keep duplicating
their guts; among the little things that had been missing there were such as
	ret = security_file_permission (file, MAY_READ);
Gotta love the LSM robustness, right?
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

sbi->s_group_desc is an array of pointers to buffer_head.  memcpy() of
buffer size from address of buffer_head is a bad idea - it will generate
junk in any case, may oops if buffer_head is close to the end of slab
page and next page is not mapped and isn't what was intended there.
IOW, ->b_data is missing in that call.  Fortunately, result doesn't go
into the primary on-disk data structures, so only backup ones get crap
written to them; that had allowed this bug to remain unnoticed until
now.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

* 'splice' of git://brick.kernel.dk/data/git/linux-2.6-block:
  [PATCH] splice: add ->splice_write support for /dev/null
  [PATCH] splice: rearrange moving to/from pipe helpers
  [PATCH] Add support for the sys_vmsplice syscall
  [PATCH] splice: fix offset problems
  [PATCH] splice: fix min() warning

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  [PATCH] forcedeth: fix initialization
  [PATCH] sky2: version 1.2
  [PATCH] sky2: reset function can be devinit
  [PATCH] sky2: use ALIGN() macro
  [PATCH] sky2: add fake idle irq timer
  [PATCH] sky2: reschedule if irq still pending
  [PATCH] bcm43xx: make PIO mode usable
  [PATCH] bcm43xx: add to MAINTAINERS
  [PATCH] softmac: fix SIOCSIWAP
  [PATCH] Fix crash on big-endian systems during scan
  e1000: Update truesize with the length of the packet for packet split
  [PATCH] Fix locking in gianfar

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [BRIDGE]: allow full size vlan packets

Useful for testing.
Signed-off-by: NJens Axboe <axboe@suse.de>

We need these for people writing their own ->splice_read/write hooks.
Signed-off-by: NJens Axboe <axboe@suse.de>

This patch fixes the nic initialization. If the nic was in low power
mode, it brings it back to normal power. Also, it utilizes a new
hardware reset during the init.

I am resending based on feedback, I corrected the register size mapping
and delay after posted write.
Signed-Off-By: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update to version 1.2
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The sky2_reset function only called from sky2_probe.
Maybe the compiler was smart enough to figure this out already.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The ALIGN() macro in kernel.h does the same math that the
sky2 driver was using for padding.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add an fake NAPI schedule once a second. This is an attempt to work around
for broken configurations with edge-triggered interrupts.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This is a workaround for the case edge-triggered irq's. Several users
seem to have broken configurations sharing edge-triggered irq's. To avoid
losing IRQ's, reshedule if more work arrives.

The changes to netdevice.h are to extract the part that puts device
back in list into separate inline.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Merge branch 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes

Need to allow for VLAN header when bridging.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sys_splice() moves data to/from pipes with a file input/output. sys_vmsplice()
moves data to a pipe, with the input being a user address range instead.

This uses an approach suggested by Linus, where we can hold partial ranges
inside the pages[] map. Hopefully this will be useful for network
receive support as well.
Signed-off-by: NJens Axboe <axboe@suse.de>

Signed-off-by: NMiklos Szeredi <miklos@szeredi.hu>

BKL does not protect against races if the task may sleep between
checking and setting a value.  So move checking of file->private_data
near to setting it in fuse_fill_super().

Found by Al Viro.
Signed-off-by: NMiklos Szeredi <miklos@szeredi.hu>