libsas handles:
1/ limiting ata scanning to lun0
2/ changes to /sys/block/<sdX>/device/queue_depth for ata devices

libata handles turning off ncq globally via kernel command line
(libata.force=noncq) or sysfs (echo 1 >
/sys/block/<sdX>/device/queue_depth).  A lldd specific compile option is
not necessary.

Cc: Jack Wang <jack_wang@usish.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

libsas now handles:
1/ limiting ata scanning to lun0
2/ maximizing the queue_depth of sas devices (up to 256, mvsas only
   supports 64)
3/ changes to /sys/block/<sdX>/device/queue_depth for ata devices
Acked-by: NXiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The queue-depth for libsas-attached devices initializes to 32 and can
only be increased manually via sysfs to a max of 64, while mpt2sas
attached devices initialize to 254 and dynamically float via the
midlayer ->change_queue_depth interface.

No performance regression was observed with this change on the isci
driver.
Tested-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Pass queue_depth change requests to libata, and prevent queue_type
changes for ATA devices.

Otherwise:
1/ we do not honor the libata specific restrictions on the queue depth
2/ libsas drivers that do not set sdev->tagged_supported are unable to
   change the queue_depth of ata devices via sysfs
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Currently mvsas and pm8001 have custom ->slave_alloc implementations to
achieve this.  Uplevel it for all libsas drivers as isci encounters problems
with atapi devices when scanning past lun0.

Just do what Darrick suggested [1], and limit the scan for ata devices.

[1] http://marc.info/?l=linux-scsi&m=116604101119861&w=2Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Allow expander table-to-table attachments for
expanders that support it.
Signed-off-by: NLuben Tuikov <ltuikov@yahoo.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When the ipr driver decides to dump the adapter, it changes the
sdt_state to GET_DUMP, then prepares the adapter so that the dump
can be read. However, if the ipr worker thread wakes up for some
reason before the driver has put the adapter in a state where it
can succesfully dump the adapter, the driver will start dumping
the adapter too early, which can potentially trigger a BUG check
in the pci config blocking API. Fix this by adding a new
sdt_state to differentiate between the ipr driver wanting to dump
the adapter in the near future and wanting to dump the adapter now.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NVijay Chauhan <Vijay.chauhan@netapp.com>
Reviewed-by: NBob Stankey <Robert.stankey@netapp.com>
Reviewed-by: NBabu Moger <Babu.moger@netapp.com>
Acked-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Gracefully handle bnx2fc_map_sg failure, so that queuecommand returns host busy
and SCSI-ml can retry the IO.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

scsi_dma_map doesn't work for NPIV since vport dev isn't fully initialized.

For more details: http://marc.info/?l=linux-scsi&m=118312448030633&w=2 and
commit - c59fd9eb.
Signed-off-by: NNithin Sujir <nsujir@broadcom.com>
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When READ_16 command is issued, the setting of SILI Bit in CDB is confirmed
and if SILI bit is off, the processing of relavent Errata is executed.

Added code for checking SILI bit for READ_16 as described in "SSC-4".
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Sizeof a pointer-typed expression returns the size of the pointer, not that
of the pointed data.

The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression *e;
type T;
identifier f;
@@

f(...,(T)e,...,
-sizeof(e)
+sizeof(*e)
,...)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

bnx2fc.txt outlines the driver usage model.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Mutual exclusion is redundant here because all the paths in the call graph
leading to esp_driver_ops.send_dma_cmd() happen under spin_lock_irqsave/
spin_lock_irqrestore. Remove it.

Tested on a Mac Quadra 660av and a Mac LC 630.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Support added for controllers capable of multi reply queues.

The following are the modifications to the driver to support NUMA.

1) Create the new structure adapter_reply_queue to contain the reply queue
   info for every msix vector.  This object will contain a
   reply_post_host_index, reply_post_free for each instance, msix_index, among
   other parameters.  We will track all the reply queues on a link list called
   ioc->reply_queue_list. Each reply queue is aligned with each IRQ, and is
   passed to the interrupt via the bus_id parameter.

(2) The driver will figure out the msix_vector_count from the PCIe MSIX
    capabilities register instead of the IOC Facts->MaxMSIxVectors. This is
    because the firmware is not filling in this field until the driver has
    already registered MSIX support.

(3) If the ioc_facts reports that the controller is MSIX compatible in the
    capabilities, then the driver will request for multiple irqs.  This count
    is calculated based on the minimum between the online cpus available and
    the ioc->msix_vector_count.  This count is reported to firmware in the
    ioc_init request.

(4) New routines were added _base_free_irq and _base_request_irq, so
    registering and freeing msix vectors were done thru simple function API.

(5) The new routine _base_assign_reply_queues was added to align the msix
    indexes across cpus. This will initialize the array called
    ioc->cpu_msix_table.  This array is looked up on every MPI request so the
    MSIxIndex is set appropriately.

(6) A new shost sysfs attribute was added to report the reply_queue_count.

(7) User needs to set the affinity cpu mask, so the interrupts occur on the
    same cpu that sent the original request.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This patch adds couple more Vendor/Product IDs for RDAC.. There are no
functional changes.
Signed-off-by: NBabu Moger <babu.moger@netapp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Basic support to initialize the gpio unit, accept an incomming
SAS_GPIO_REG_TX_GP bitstream, and translate it to the ODx.n fields in
the hardware registers.  If register indexes outside the supported range
are specified in the SMP frame we simply accept the write and return how
many registers (SFF-8485) were written (libsas reports this as residue
in the request).
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

output_data_select registers are off by one u32

delete the macros we will never use.
Reported-by: NArtur Wojcik <artur.wojcik@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Add SFF-8485 v0.7 / SAS-1 smp-write-gpio register support to libsas.
Defer SAS-2 support unless/until it defines an sgpio interface.

Minimum implementation needed to get the lights blinking.
try_test_sas_gpio_gp_bit() provides a common method to parse the
incoming write data (raw bitstream), and the to_sas_gpio_gp_bit() helper
routine can be used as a basis for the set/clear operations for the
'read' implementation.  Host implementations parse as many bits
(ODx.[012]) as are locally supported and report the number of registers
successfully written.  If the submitted data overruns the internal
number of registers available report the write as a success with the
number of bytes remaining reported in ->resid_len.

Example (assuming an active backplane) set the "identify" pattern for
the first 21 devices:

smp_write_gpio --count=2 --data=92,49,24,92,24,92,49,24 -t 4 --index=1 /dev/bsg/sas_hostX
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

qla4xxx now uses iscsi_boot_sysfs to export the targets used
for boot to sysfs. It needs to select that config option
to make sure that module is also built.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Firmware asserts when the same CQE is armed twice. This scenario happens during
RSCN stress tests as driver incorrects arms the CQ after the session is
offloaded.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Driver incorrectly calls bnx2fc_interface_cleanup() when bnx2fc_if_create fails
which accesses bad pointer. Handle bnx2fc_if_create failure by directly calling
bnx2fc_net_cleanup.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

It is not required to hold rtnl_lock and bnx2fc_dev_lock when calling
bnx2fc_if_destroy, as the locking is only required to serialize creation and
deletion of fcoe instances. More importantly, this unnecessary locking causes
deadlock as bnx2fc_if_destroy calls fc_remove_host holding rtnl_lock.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When bnx2fc receives an UNREGISTER event on a vlan interface it calls
destroy on all interfaces that matches the physical interface. Add
vlan_id check to destroy only the vlan interface that generated the
event.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

ABTS was not issued for timed out REC, as REC completion handler exits out if
the IO completed. Check for timed out REC and issue ABTS before proceeding with
further processing in REC completion handler. Also, initialize rec_retry and
srr_retry before starting the IO.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Link up event is generated to the driver even before vlan discovery has
started. Because of this driver can send discovery solicitation on a stale
vlan. Call fcoe_ctlr_link_up() only when the driver is in enabled state, which
implies the vlan discovery is complete before sending solicitation.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If the max receive frame size is changed during link down, the driver uses the
same value after linkup unless it is reset to default.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The alua device handler starts the first retry after 10 seconds,
and increases it times 10 for each round.
This leads to an unnecessary delay. This patch modifies it to
start after one second, and increase by a factor of two.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

For Target Portal Group IDs occupying the full 2 bytes in the
RTPG response, the following group_id check in the alua_rtpg
routine always fails in scsi_dh_alua.c:

if (h->group_id == (ucp[2] << 8) + ucp[3]) {

This causes the ALUA handler to wrongly identify the AAS of
a specified device as well as incorrectly interpreting the
supported AAS of the target as seen by the following entries
in the /var/log/messages:

"alua: port group 3ea state A supports tousna"
"alua: port group 3e9 state A supports tousna"

This is because 'ucp' is wrongly declared in alua_rtpg as
a character pointer instead of an unsigned character pointer.
Signed-off-by: NMartin George <marting@netapp.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Avoid attaching a hardware handler to a device which is
already scheduled for deletion.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When activating a patch we should always update the TPGS state
as it might have changed in between.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Some device handler types are not tied to the vendor/model
but rather to a specific capability. Eg ALUA is supported
if the 'TPGS' setting in the standard inquiry is set.
This patch implements a 'match' callback for device handler
which supersedes the original vendor/model lookup and
implements the callback for the ALUA handler.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fixup some kernel-doc comments to reference to the
correct function name.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Instead of issuing a standard inquiry from within the
alua device handler we can evaluate the TPGS setting from
the existing inquiry data of the sdev and save us the I/O.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

->queuecommand must return either 0, or one of the SCSI_MLQUEUE_* return
values.  Non-transient errors are indicated by setting cmd->result before
calling ->scsi_done and returning 0.  Fix libsas to adhere to this calling
convention.  Note that the DID_ERROR for returns from the low-level driver
might not be correct for all cases, but it's the best we can do with
the current layering in libsas.  I also suspect that the pre-existing
handling of -SAS_QUEUE_FULL should really be SCSI_MLQUEUE_HOST_BUSY, but
I'll leave that for a separate change.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Switch sas_queuecommand to a normal indentation and goto based error handling.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>