p9_virtio_create will only compare the the channel's tag characters
against the device name till the end of the channel's tag but not till
the end of the device name. This means that if a user defines channels
with the tags foo and foobar then he would mount foo when he requested
foonot and may mount foo when he requested foobar.

Thus it is necessary to check both string lengths against each other in
case of a successful partial string match.
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the interface is up, using ethtool breaks it because:
a) link is put down but media_timer interval is not shortened to NO_LINK
b) rxtx is stopped but not restarted

Also manual 10baseT-HD (and probably FD too - untested) mode does not work -
the link is forced up, packets are transmitted but nothing is received.
Changing CSR14 value to match documentation (not disabling link check) fixes this.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

as done in ip_route_connect()
Signed-off-by: NUlrich Weber <uweber@astaro.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IPv4 and IPv6 have separate neighbour tables, so
the warning messages should be distinguishable.

[ Add a suitable message prefix on the ipv4 side as well -DaveM ]
Signed-off-by: NUlrich Weber <uweber@astaro.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When TCP uses FACK algorithm to mark lost packets in
tcp_mark_head_lost(), if the number of packets in the (TSO) skb is
greater than the number of packets that should be marked lost, TCP
incorrectly exits the loop and marks no packets lost in the skb. This
underestimates tp->lost_out and affects the recovery/retransmission.
This patch fargments the skb and marks the correct amount of packets
lost.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch (commit 690a1f20) added a
new call site for acpi_set_WOL() without checking that the function is
actually suitable to be called via

 vortex_set_wol+0xcd/0xe0 [3c59x]
 dev_ethtool+0xa5a/0xb70
 dev_ioctl+0x2e0/0x4b0
 T.961+0x49/0x50
 sock_ioctl+0x47/0x290
 do_vfs_ioctl+0x7f/0x340
 sys_ioctl+0x80/0xa0
 system_call_fastpath+0x16/0x1b

i.e. outside of code paths run when the device is not yet enabled or
already disabled. In particular, putting the device into D3hot is a
pretty bad idea when it was already brought up.

Furthermore, all prior callers of the function made sure they're
actually dealing with a PCI device, while the newly added one didn't.

In the same spirit, the .get_wol handler shouldn't indicate support
for WOL for non-PCI devices.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clean up a missing exit path in the ipv6 module init routines.  In
addrconf_init we call ipv6_addr_label_init which calls register_pernet_subsys
for the ipv6_addr_label_ops structure.  But if module loading fails, or if the
ipv6 module is removed, there is no corresponding unregister_pernet_subsys call,
which leaves a now-bogus address on the pernet_list, leading to oopses in
subsequent registrations.  This patch cleans up both the failed load path and
the unload path.  Tested by myself with good results.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>

 include/net/addrconf.h |    1 +
 net/ipv6/addrconf.c    |   11 ++++++++---
 net/ipv6/addrlabel.c   |    5 +++++
 3 files changed, 14 insertions(+), 3 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

@@
struct net_device* dev;
@@

-kfree(dev)
+free_netdev(dev)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

@@
struct net_device* dev;
@@

-kfree(dev)
+free_netdev(dev)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

@@
struct net_device* dev;
@@

-kfree(dev)
+free_netdev(dev)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

@@
struct net_device* dev;
@@

-kfree(dev)
+free_netdev(dev)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This enables auto loading for the smsc911x ethernet driver.
Signed-off-by: NVincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reset queue mapping when an skb is reentering the stack via a tunnel.
On second pass, the queue mapping from the original device is no
longer valid.
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

You can't call atomic_notifier_chain_unregister() while in atomic context.

Fix, call un/register_atmdevice_notifier in module __init and __exit.

Bug report:
http://comments.gmane.org/gmane.linux.network/172603Reported-by: NMikko Vinni <mmvinni@yahoo.com>
Tested-by: NMikko Vinni <mmvinni@yahoo.com>
Signed-off-by: NKarl Hiramoto <karl@hiramoto.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compex FreedomLine 32 PnP-PCI2 cards have only TP and BNC connectors but the
SROM contains AUI port too. When TP loses link, the driver switches to
non-existing AUI port (which reports that carrier is always present).

Connecting TP back generates LinkPass interrupt but de_media_interrupt() is
broken - it only updates the link state of currently connected media, ignoring
the fact that LinkPass and LinkFail bits of MacStatus register belong to the
TP port only (the chip documentation says that).

This patch changes de_media_interrupt() to switch media to TP when link goes
up (and media type is not locked) and also to update the link state only when
the TP port is used.

Also the NonselPortActive (and also SelPortActive) bits of SIAStatus register
need to be cleared (by writing 1) after reading or they're useless.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At least my 21041 cards come out of suspend with bus mastering disabled so
they did not work after resume(no data transferred).
After adding pci_set_master(), the driver oopsed immediately on resume -
because de_clean_rings() is called on suspend but de_init_rings() call
was missing in resume.

Also disable link (reset SIA) before sleep (de4x5 does this too).
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At least on older 21041-AA chips (mine is rev. 11), TP duplex autonegotiation
causes the card not to work at all (link is up but no packets are transmitted).

de4x5 disables autonegotiation completely. But it seems to work on newer
(21041-PA rev. 21) so disable it only on rev<20 chips.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have for each socket :

One spinlock (sk_slock.slock)
One rwlock (sk_callback_lock)

Possible scenarios are :

(A) (this is used in net/sunrpc/xprtsock.c)
read_lock(&sk->sk_callback_lock) (without blocking BH)
<BH>
spin_lock(&sk->sk_slock.slock);
...
read_lock(&sk->sk_callback_lock);
...

(B)
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)

(C)
spin_lock_bh(&sk->sk_slock)
...
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)
spin_unlock_bh(&sk->sk_slock)

This (C) case conflicts with (A) :

CPU1 [A]                         CPU2 [C]
read_lock(callback_lock)
<BH>                             spin_lock_bh(slock)
<wait to spin_lock(slock)>
                                 <wait to write_lock_bh(callback_lock)>

We have one problematic (C) use case in inet_csk_listen_stop() :

local_bh_disable();
bh_lock_sock(child); // spin_lock_bh(&sk->sk_slock)
WARN_ON(sock_owned_by_user(child));
...
sock_orphan(child); // write_lock_bh(&sk->sk_callback_lock)

lockdep is not happy with this, as reported by Tetsuo Handa

It seems only way to deal with this is to use read_lock_bh(callbacklock)
everywhere.

Thanks to Jarek for pointing a bug in my first attempt and suggesting
this solution.
Reported-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
Tested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For non-managed versions of 82579, set the bit that prevents the hardware
from automatically configuring the PHY after resets only when the driver
performs a reset, clear the bit after resets.  This is so the hardware can
configure the PHY automatically when the part is reset in a manner that is
not controlled by the driver (e.g. in a virtual environment via PCI FLR)
otherwise the PHY will be mis-configured causing issues such as failing to
link at 1000Mbps.
For managed versions of 82579, keep the previous behavior since the
manageability firmware will handle the PHY configuration.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The subject workaround was causing CRC errors due to writing the wrong
register with updates of the RCTL register.  It was also found that the
workaround function which modifies the RCTL register was being called in
the middle of a read-modify-write operation of the RCTL register, so the
function call has been moved appropriately.  Lastly, jumbo frames must not
be allowed when CRC stripping is disabled by a module parameter because the
workaround requires the CRC be stripped.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On 82579, there is a hardware bug that can cause received packets to not
get transferred from the PHY to the MAC due to K1 (a power saving feature
of the PHY-MAC interconnect similar to ASPM L1).  Since the MAC controls
the accounting of missed packets, these will go unnoticed.  Workaround the
issue by setting the K1 beacon duration according to the link speed.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Two recent patches to cleanup the reset[1] and initial PHY configuration[2]
code paths for ICH/PCH devices inadvertently left out a 10msec delay and
device ID check respectively which are necessary for the 82566DC (device id
0x104b) to be configured properly, otherwise it will not get link.

[1] commit e98cac44
[2] commit 3f0c16e8

CC: stable@kernel.org
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the hardware is prevented from performing automatic PHY configuration
(the driver does it instead), the OEM_WRITE_ENABLE bit in the EXTCNF_CTRL
register will not get cleared preventing the SMBus address and the LED
configuration to be written to the PHY registers.  On 82579, do not check
the OEM_WRITE_ENABLE bit.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When going to Sx, disable gigabit in PHY (e1000_oem_bits_config_ich8lan)
in addition to the MAC before configuring PHY wakeup otherwise the PHY
configuration writes might be missed.  Also write the LED configuration
and SMBus address to the PHY registers (e1000_oem_bits_config_ich8lan and
e1000_write_smbus_addr, respectively).  The reset is no longer needed
since re-auto-negotiation is forced in e1000_oem_bits_config_ich8lan and
leaving it in causes issues with auto-negotiating the link.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

otherwise ECT(1) bit will get interpreted as RTO_ONLINK
and routing will fail with XfrmOutBundleGenError.
Signed-off-by: NUlrich Weber <uweber@astaro.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

They are allocated in atl1_setup_ring_resources, zero out the pointers
in atl1_free_ring_resources (like the other resources).
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Acked-by: NChris Snook <chris.snook@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

adapter->cmb.cmb is initialized when the device is opened and freed when
it's closed. Accessing it unconditionally during resume results either
in a crash (NULL pointer dereference, when the interface has not been
opened yet) or data corruption (when the interface has been used and
brought down adapter->cmb.cmb points to a deallocated memory area).

Cc: stable@kernel.org
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Acked-by: NChris Snook <chris.snook@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reduces namespace pollution by moving the "struct net" declaration
out of the userspace-facing portion of linux/netlink.h.  It has no impact on
the kernel.

(This came up because we have several C++ applications which use "net" as a
namespace name.)
Signed-off-by: NOllie Wild <aaw@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

we need to check proper socket type within ipv4_conntrack_defrag
function before referencing the nodefrag flag.

For example the tun driver receive path produces skbs with
AF_UNSPEC socket type, and so current code is causing unwanted
fragmented packets going out.
Signed-off-by: NJiri Olsa <jolsa@redhat.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix checksum calculation in nf_nat_snmp_basic.

Based on patches by Clark Wang <wtweeker@163.com> and
Stephen Hemminger <shemminger@vyatta.com>.

https://bugzilla.kernel.org/show_bug.cgi?id=17622Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As soon as rcu_read_unlock() is called, there is no guarantee current
thread can safely derefence t pointer, rcu protected.

Fix is to copy t->alloc_size in a temporary variable.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip_route_me_harder can't create the route cache when the outdev is the same
with the indev for the skbs whichout a valid protocol set.

__mkroute_input functions has this check:
1998         if (skb->protocol != htons(ETH_P_IP)) {
1999                 /* Not IP (i.e. ARP). Do not create route, if it is
2000                  * invalid for proxy arp. DNAT routes are always valid.
2001                  *
2002                  * Proxy arp feature have been extended to allow, ARP
2003                  * replies back to the same interface, to support
2004                  * Private VLAN switch technologies. See arp.c.
2005                  */
2006                 if (out_dev == in_dev &&
2007                     IN_DEV_PROXY_ARP_PVLAN(in_dev) == 0) {
2008                         err = -EINVAL;
2009                         goto cleanup;
2010                 }
2011         }

This patch gives the new skb a valid protocol to bypass this check. In order
to make ipt_REJECT work with bridges, you also need to enable ip_forward.

This patch also fixes a regression. When we used skb_copy_expand(), we
didn't have this issue stated above, as the protocol was properly set.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I initially noticed this because of the compiler warning below, but it
does seem to be a valid concern in the case where ct_sip_get_header()
returns 0 in the first iteration of the while loop.

net/netfilter/nf_conntrack_sip.c: In function 'sip_help_tcp':
net/netfilter/nf_conntrack_sip.c:1379: warning: 'ret' may be used uninitialized in this function
Signed-off-by: NSimon Horman <horms@verge.net.au>
[Patrick: changed NF_DROP to NF_ACCEPT]
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

transparent field of a socket is either inet_twsk(sk)->tw_transparent
for timewait sockets, or inet_sk(sk)->transparent for other sockets
(TCP/UDP).
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The log eventfd signalling got put in dead code.
We didn't notice because qemu currently does polling
instead of eventfd select.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Special care should be taken when slow path is hit in ip_fragment() :

When walking through frags, we transfert truesize ownership from skb to
frags. Then if we hit a slow_path condition, we must undo this or risk
uncharging frags->truesize twice, and in the end, having negative socket
sk_wmem_alloc counter, or even freeing socket sooner than expected.

Many thanks to Nick Bowler, who provided a very clean bug report and
test program.

Thanks to Jarek for reviewing my first patch and providing a V2

While Nick bisection pointed to commit 2b85a34e (net: No more
expensive sock_hold()/sock_put() on each tx), underlying bug is older
(2.6.12-rc5)

A side effect is to extend work done in commit b2722b1c
(ip_fragment: also adjust skb->truesize for packets not owned by a
socket) to ipv6 as well.
Reported-and-bisected-by: NNick Bowler <nbowler@elliptictech.com>
Tested-by: NNick Bowler <nbowler@elliptictech.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->truesize is set in core network.

Dont change it unless dealing with fragments.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->truesize is set in core network.

Dont change it unless dealing with fragments.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>