usb: musb: Start using struct usb_otg

Use struct usb_otg members with OTG specific functions instead
of usb_phy members.

[ balbi@ti.com: added a missing change on musb_gadget.c to avoid
	a compile error on a later patch ]
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

drivers/usb/musb/am35x.c

@@ -226,6 +226,7 @@ static irqreturn_t am35x_musb_interrupt(int irq, void *hci)
 	struct device *dev = musb->controller;
 	struct musb_hdrc_platform_data *plat = dev->platform_data;
 	struct omap_musb_board_data *data = plat->board_data;
+	struct usb_otg *otg = musb->xceiv->otg;
 	unsigned long flags;
 	irqreturn_t ret = IRQ_NONE;
 	u32 epintr, usbintr;
@@ -289,14 +290,14 @@ static irqreturn_t am35x_musb_interrupt(int irq, void *hci)
 			WARNING("VBUS error workaround (delay coming)\n");
 		} else if (is_host_enabled(musb) && drvvbus) {
 			MUSB_HST_MODE(musb);
-			musb->xceiv->default_a = 1;
+			otg->default_a = 1;
 			musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
 			portstate(musb->port1_status |= USB_PORT_STAT_POWER);
 			del_timer(&otg_workaround);
 		} else {
 			musb->is_active = 0;
 			MUSB_DEV_MODE(musb);
-			musb->xceiv->default_a = 0;
+			otg->default_a = 0;
 			musb->xceiv->state = OTG_STATE_B_IDLE;
 			portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
 		}

drivers/usb/musb/da8xx.c

@@ -294,6 +294,7 @@ static irqreturn_t da8xx_musb_interrupt(int irq, void *hci)
 {
 	struct musb		*musb = hci;
 	void __iomem		*reg_base = musb->ctrl_base;
+	struct usb_otg		*otg = musb->xceiv->otg;
 	unsigned long		flags;
 	irqreturn_t		ret = IRQ_NONE;
 	u32			status;
@@ -351,14 +352,14 @@ static irqreturn_t da8xx_musb_interrupt(int irq, void *hci)
 			WARNING("VBUS error workaround (delay coming)\n");
 		} else if (is_host_enabled(musb) && drvvbus) {
 			MUSB_HST_MODE(musb);
-			musb->xceiv->default_a = 1;
+			otg->default_a = 1;
 			musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
 			portstate(musb->port1_status |= USB_PORT_STAT_POWER);
 			del_timer(&otg_workaround);
 		} else {
 			musb->is_active = 0;
 			MUSB_DEV_MODE(musb);
-			musb->xceiv->default_a = 0;
+			otg->default_a = 0;
 			musb->xceiv->state = OTG_STATE_B_IDLE;
 			portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
 		}

drivers/usb/musb/davinci.c

@@ -265,6 +265,7 @@ static irqreturn_t davinci_musb_interrupt(int irq, void *__hci)
 	unsigned long	flags;
 	irqreturn_t	retval = IRQ_NONE;
 	struct musb	*musb = __hci;
+	struct usb_otg	*otg = musb->xceiv->otg;
 	void __iomem	*tibase = musb->ctrl_base;
 	struct cppi	*cppi;
 	u32		tmp;
@@ -331,14 +332,14 @@ static irqreturn_t davinci_musb_interrupt(int irq, void *__hci)
 			WARNING("VBUS error workaround (delay coming)\n");
 		} else if (is_host_enabled(musb) && drvvbus) {
 			MUSB_HST_MODE(musb);
-			musb->xceiv->default_a = 1;
+			otg->default_a = 1;
 			musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
 			portstate(musb->port1_status |= USB_PORT_STAT_POWER);
 			del_timer(&otg_workaround);
 		} else {
 			musb->is_active = 0;
 			MUSB_DEV_MODE(musb);
-			musb->xceiv->default_a = 0;
+			otg->default_a = 0;
 			musb->xceiv->state = OTG_STATE_B_IDLE;
 			portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
 		}
@@ -464,7 +465,7 @@ static int davinci_musb_exit(struct musb *musb)
 	davinci_musb_source_power(musb, 0 /*off*/, 1);
 
 	/* delay, to avoid problems with module reload */
-	if (is_host_enabled(musb) && musb->xceiv->default_a) {
+	if (is_host_enabled(musb) && musb->xceiv->otg->default_a) {
 		int	maxdelay = 30;
 		u8	devctl, warn = 0;
 

drivers/usb/musb/musb_core.c

@@ -414,6 +414,7 @@ void musb_hnp_stop(struct musb *musb)
 static irqreturn_t musb_stage0_irq(struct musb *musb, u8 int_usb,
 				u8 devctl, u8 power)
 {
+	struct usb_otg *otg = musb->xceiv->otg;
 	irqreturn_t handled = IRQ_NONE;
 
 	dev_dbg(musb->controller, "<== Power=%02x, DevCtl=%02x, int_usb=0x%x\n", power, devctl,
@@ -626,7 +627,7 @@ static irqreturn_t musb_stage0_irq(struct musb *musb, u8 int_usb,
 		case OTG_STATE_B_PERIPHERAL:
 			musb_g_suspend(musb);
 			musb->is_active = is_otg_enabled(musb)
-					&& musb->xceiv->gadget->b_hnp_enable;
+					&& otg->gadget->b_hnp_enable;
 			if (musb->is_active) {
 				musb->xceiv->state = OTG_STATE_B_WAIT_ACON;
 				dev_dbg(musb->controller, "HNP: Setting timer for b_ase0_brst\n");
@@ -643,7 +644,7 @@ static irqreturn_t musb_stage0_irq(struct musb *musb, u8 int_usb,
 		case OTG_STATE_A_HOST:
 			musb->xceiv->state = OTG_STATE_A_SUSPEND;
 			musb->is_active = is_otg_enabled(musb)
-					&& musb->xceiv->host->b_hnp_enable;
+					&& otg->host->b_hnp_enable;
 			break;
 		case OTG_STATE_B_HOST:
 			/* Transition to B_PERIPHERAL, see 6.8.2.6 p 44 */
@@ -1965,7 +1966,7 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl)
 
 		if (is_otg_enabled(musb))
 			hcd->self.otg_port = 1;
-		musb->xceiv->host = &hcd->self;
+		musb->xceiv->otg->host = &hcd->self;
 		hcd->power_budget = 2 * (plat->power ? : 250);
 
 		/* program PHY to use external vBus if required */
@@ -1984,7 +1985,7 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl)
 		struct usb_hcd	*hcd = musb_to_hcd(musb);
 
 		MUSB_HST_MODE(musb);
-		musb->xceiv->default_a = 1;
+		musb->xceiv->otg->default_a = 1;
 		musb->xceiv->state = OTG_STATE_A_IDLE;
 
 		status = usb_add_hcd(musb_to_hcd(musb), -1, 0);
@@ -1999,7 +2000,7 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl)
 
 	} else /* peripheral is enabled */ {
 		MUSB_DEV_MODE(musb);
-		musb->xceiv->default_a = 0;
+		musb->xceiv->otg->default_a = 0;
 		musb->xceiv->state = OTG_STATE_B_IDLE;
 
 		status = musb_gadget_setup(musb);

drivers/usb/musb/musb_gadget.c

@@ -1898,6 +1898,7 @@ static int musb_gadget_start(struct usb_gadget *g,
 		struct usb_gadget_driver *driver)
 {
 	struct musb		*musb = gadget_to_musb(g);
+	struct usb_otg		*otg = musb->xceiv->otg;
 	unsigned long		flags;
 	int			retval = -EINVAL;
 
@@ -1945,7 +1946,7 @@ static int musb_gadget_start(struct usb_gadget *g,
 		}
 
 		if ((musb->xceiv->last_event == USB_EVENT_ID)
-					&& musb->xceiv->set_vbus)
+					&& otg->set_vbus)
 			otg_set_vbus(musb->xceiv, 1);
 
 		hcd->self.uses_pio_for_control = 1;

drivers/usb/musb/musb_virthub.c

@@ -47,6 +47,7 @@
 
 static void musb_port_suspend(struct musb *musb, bool do_suspend)
 {
+	struct usb_otg	*otg = musb->xceiv->otg;
 	u8		power;
 	void __iomem	*mbase = musb->mregs;
 
@@ -81,7 +82,7 @@ static void musb_port_suspend(struct musb *musb, bool do_suspend)
 		case OTG_STATE_A_HOST:
 			musb->xceiv->state = OTG_STATE_A_SUSPEND;
 			musb->is_active = is_otg_enabled(musb)
-					&& musb->xceiv->host->b_hnp_enable;
+					&& otg->host->b_hnp_enable;
 			if (musb->is_active)
 				mod_timer(&musb->otg_timer, jiffies
 					+ msecs_to_jiffies(
@@ -91,7 +92,7 @@ static void musb_port_suspend(struct musb *musb, bool do_suspend)
 		case OTG_STATE_B_HOST:
 			musb->xceiv->state = OTG_STATE_B_WAIT_ACON;
 			musb->is_active = is_otg_enabled(musb)
-					&& musb->xceiv->host->b_hnp_enable;
+					&& otg->host->b_hnp_enable;
 			musb_platform_try_idle(musb, 0);
 			break;
 		default:
@@ -179,6 +180,8 @@ static void musb_port_reset(struct musb *musb, bool do_reset)
 
 void musb_root_disconnect(struct musb *musb)
 {
+	struct usb_otg	*otg = musb->xceiv->otg;
+
 	musb->port1_status = USB_PORT_STAT_POWER
 			| (USB_PORT_STAT_C_CONNECTION << 16);
 
@@ -188,7 +191,7 @@ void musb_root_disconnect(struct musb *musb)
 	switch (musb->xceiv->state) {
 	case OTG_STATE_A_SUSPEND:
 		if (is_otg_enabled(musb)
-				&& musb->xceiv->host->b_hnp_enable) {
+				&& otg->host->b_hnp_enable) {
 			musb->xceiv->state = OTG_STATE_A_PERIPHERAL;
 			musb->g.is_a_peripheral = 1;
 			break;

drivers/usb/musb/omap2430.c

@@ -132,6 +132,7 @@ static void omap2430_musb_try_idle(struct musb *musb, unsigned long timeout)
 
 static void omap2430_musb_set_vbus(struct musb *musb, int is_on)
 {
+	struct usb_otg	*otg = musb->xceiv->otg;
 	u8		devctl;
 	unsigned long timeout = jiffies + msecs_to_jiffies(1000);
 	int ret = 1;
@@ -167,7 +168,7 @@ static void omap2430_musb_set_vbus(struct musb *musb, int is_on)
 				otg_set_vbus(musb->xceiv, 1);
 		} else {
 			musb->is_active = 1;
-			musb->xceiv->default_a = 1;
+			otg->default_a = 1;
 			musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
 			devctl |= MUSB_DEVCTL_SESSION;
 			MUSB_HST_MODE(musb);
@@ -179,7 +180,7 @@ static void omap2430_musb_set_vbus(struct musb *musb, int is_on)
 		 * jumping right to B_IDLE...
 		 */
 
-		musb->xceiv->default_a = 0;
+		otg->default_a = 0;
 		musb->xceiv->state = OTG_STATE_B_IDLE;
 		devctl &= ~MUSB_DEVCTL_SESSION;
 

drivers/usb/musb/tusb6010.c

@@ -293,7 +293,7 @@ static int tusb_draw_power(struct usb_phy *x, unsigned mA)
 	 * The actual current usage would be very board-specific.  For now,
 	 * it's simpler to just use an aggregate (also board-specific).
 	 */
-	if (x->default_a || mA < (musb->min_power << 1))
+	if (x->otg->default_a || mA < (musb->min_power << 1))
 		mA = 0;
 
 	reg = musb_readl(tbase, TUSB_PRCM_MNGMT);
@@ -510,6 +510,7 @@ static void tusb_musb_set_vbus(struct musb *musb, int is_on)
 	void __iomem	*tbase = musb->ctrl_base;
 	u32		conf, prcm, timer;
 	u8		devctl;
+	struct usb_otg	*otg = musb->xceiv->otg;
 
 	/* HDRC controls CPEN, but beware current surges during device
 	 * connect.  They can trigger transient overcurrent conditions
@@ -522,7 +523,7 @@ static void tusb_musb_set_vbus(struct musb *musb, int is_on)
 
 	if (is_on) {
 		timer = OTG_TIMER_MS(OTG_TIME_A_WAIT_VRISE);
-		musb->xceiv->default_a = 1;
+		otg->default_a = 1;
 		musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
 		devctl |= MUSB_DEVCTL_SESSION;
 
@@ -548,11 +549,11 @@ static void tusb_musb_set_vbus(struct musb *musb, int is_on)
 				musb->xceiv->state = OTG_STATE_A_IDLE;
 			}
 			musb->is_active = 0;
-			musb->xceiv->default_a = 1;
+			otg->default_a = 1;
 			MUSB_HST_MODE(musb);
 		} else {
 			musb->is_active = 0;
-			musb->xceiv->default_a = 0;
+			otg->default_a = 0;
 			musb->xceiv->state = OTG_STATE_B_IDLE;
 			MUSB_DEV_MODE(musb);
 		}
@@ -644,6 +645,7 @@ tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase)
 {
 	u32		otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT);
 	unsigned long	idle_timeout = 0;
+	struct usb_otg	*otg = musb->xceiv->otg;
 
 	/* ID pin */
 	if ((int_src & TUSB_INT_SRC_ID_STATUS_CHNG)) {
@@ -654,7 +656,7 @@ tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase)
 		else
 			default_a = is_host_enabled(musb);
 		dev_dbg(musb->controller, "Default-%c\n", default_a ? 'A' : 'B');
-		musb->xceiv->default_a = default_a;
+		otg->default_a = default_a;
 		tusb_musb_set_vbus(musb, default_a);
 
 		/* Don't allow idling immediately */
@@ -666,7 +668,7 @@ tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase)
 	if (int_src & TUSB_INT_SRC_VBUS_SENSE_CHNG) {
 
 		/* B-dev state machine:  no vbus ~= disconnect */
-		if ((is_otg_enabled(musb) && !musb->xceiv->default_a)
+		if ((is_otg_enabled(musb) && !otg->default_a)
 				|| !is_host_enabled(musb)) {
 			/* ? musb_root_disconnect(musb); */
 			musb->port1_status &=