提交 b6e61eef 编写于 作者: L Linus Torvalds 提交者: Ingo Molnar

x86: Fix serialization in pit_expect_msb()

Wei Chong Tan reported a fast-PIT-calibration corner-case:

| pit_expect_msb() is vulnerable to SMI disturbance corner case
| in some platforms which causes /proc/cpuinfo to show wrong
| CPU MHz value when quick_pit_calibrate() jumps to success
| section.

I think that the real issue isn't even an SMI - but the fact
that in the very last iteration of the loop, there's no
serializing instruction _after_ the last 'rdtsc'. So even in
the absense of SMI's, we do have a situation where the cycle
counter was read without proper serialization.

The last check should be done outside the outer loop, since
_inside_ the outer loop, we'll be testing that the PIT has
the right MSB value has the right value in the next iteration.

So only the _last_ iteration is special, because that's the one
that will not check the PIT MSB value any more, and because the
final 'get_cycles()' isn't serialized.

In other words:

 - I'd like to move the PIT MSB check to after the last
   iteration, rather than in every iteration

 - I think we should comment on the fact that it's also a
   serializing instruction and so 'fences in' the TSC read.

Here's a suggested replacement.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Reported-by: N"Tan, Wei Chong" <wei.chong.tan@intel.com>
Tested-by: N"Tan, Wei Chong" <wei.chong.tan@intel.com>
LKML-Reference: <B28277FD4E0F9247A3D55704C440A140D5D683F3@pgsmsx504.gar.corp.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
上级 f4b9a988
......@@ -275,15 +275,20 @@ static unsigned long pit_calibrate_tsc(u32 latch, unsigned long ms, int loopmin)
* use the TSC value at the transitions to calculate a pretty
* good value for the TSC frequencty.
*/
static inline int pit_verify_msb(unsigned char val)
{
/* Ignore LSB */
inb(0x42);
return inb(0x42) == val;
}
static inline int pit_expect_msb(unsigned char val, u64 *tscp, unsigned long *deltap)
{
int count;
u64 tsc = 0;
for (count = 0; count < 50000; count++) {
/* Ignore LSB */
inb(0x42);
if (inb(0x42) != val)
if (!pit_verify_msb(val))
break;
tsc = get_cycles();
}
......@@ -336,8 +341,7 @@ static unsigned long quick_pit_calibrate(void)
* to do that is to just read back the 16-bit counter
* once from the PIT.
*/
inb(0x42);
inb(0x42);
pit_verify_msb(0);
if (pit_expect_msb(0xff, &tsc, &d1)) {
for (i = 1; i <= MAX_QUICK_PIT_ITERATIONS; i++) {
......@@ -348,8 +352,19 @@ static unsigned long quick_pit_calibrate(void)
* Iterate until the error is less than 500 ppm
*/
delta -= tsc;
if (d1+d2 < delta >> 11)
goto success;
if (d1+d2 >= delta >> 11)
continue;
/*
* Check the PIT one more time to verify that
* all TSC reads were stable wrt the PIT.
*
* This also guarantees serialization of the
* last cycle read ('d2') in pit_expect_msb.
*/
if (!pit_verify_msb(0xfe - i))
break;
goto success;
}
}
printk("Fast TSC calibration failed\n");
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册