提交 a485df4b 编写于 作者: V Vinod Koul

spi, serial: move to dma_transfer_direction

fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves spi, serial drivers to use new enum
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: NMika Westerberg <mika.westerberg@iki.fi>
上级 05f5799c
......@@ -131,7 +131,7 @@ static int mid_spi_dma_transfer(struct dw_spi *dws, int cs_change)
rxchan = dws->rxchan;
/* 2. Prepare the TX dma transfer */
txconf.direction = DMA_TO_DEVICE;
txconf.direction = DMA_MEM_TO_DEV;
txconf.dst_addr = dws->dma_addr;
txconf.dst_maxburst = LNW_DMA_MSIZE_16;
txconf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
......@@ -147,13 +147,13 @@ static int mid_spi_dma_transfer(struct dw_spi *dws, int cs_change)
txdesc = txchan->device->device_prep_slave_sg(txchan,
&dws->tx_sgl,
1,
DMA_TO_DEVICE,
DMA_MEM_TO_DEV,
DMA_PREP_INTERRUPT | DMA_COMPL_SKIP_DEST_UNMAP);
txdesc->callback = dw_spi_dma_done;
txdesc->callback_param = dws;
/* 3. Prepare the RX dma transfer */
rxconf.direction = DMA_FROM_DEVICE;
rxconf.direction = DMA_DEV_TO_MEM;
rxconf.src_addr = dws->dma_addr;
rxconf.src_maxburst = LNW_DMA_MSIZE_16;
rxconf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
......@@ -169,7 +169,7 @@ static int mid_spi_dma_transfer(struct dw_spi *dws, int cs_change)
rxdesc = rxchan->device->device_prep_slave_sg(rxchan,
&dws->rx_sgl,
1,
DMA_FROM_DEVICE,
DMA_DEV_TO_MEM,
DMA_PREP_INTERRUPT | DMA_COMPL_SKIP_DEST_UNMAP);
rxdesc->callback = dw_spi_dma_done;
rxdesc->callback_param = dws;
......
......@@ -550,6 +550,7 @@ ep93xx_spi_dma_prepare(struct ep93xx_spi *espi, enum dma_data_direction dir)
struct dma_async_tx_descriptor *txd;
enum dma_slave_buswidth buswidth;
struct dma_slave_config conf;
enum dma_transfer_direction slave_dirn;
struct scatterlist *sg;
struct sg_table *sgt;
struct dma_chan *chan;
......@@ -572,6 +573,7 @@ ep93xx_spi_dma_prepare(struct ep93xx_spi *espi, enum dma_data_direction dir)
conf.src_addr = espi->sspdr_phys;
conf.src_addr_width = buswidth;
slave_dirn = DMA_DEV_TO_MEM;
} else {
chan = espi->dma_tx;
buf = t->tx_buf;
......@@ -579,6 +581,7 @@ ep93xx_spi_dma_prepare(struct ep93xx_spi *espi, enum dma_data_direction dir)
conf.dst_addr = espi->sspdr_phys;
conf.dst_addr_width = buswidth;
slave_dirn = DMA_MEM_TO_DEV;
}
ret = dmaengine_slave_config(chan, &conf);
......@@ -630,7 +633,7 @@ ep93xx_spi_dma_prepare(struct ep93xx_spi *espi, enum dma_data_direction dir)
return ERR_PTR(-ENOMEM);
txd = chan->device->device_prep_slave_sg(chan, sgt->sgl, nents,
dir, DMA_CTRL_ACK);
slave_dirn, DMA_CTRL_ACK);
if (!txd) {
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
return ERR_PTR(-ENOMEM);
......@@ -978,7 +981,7 @@ static int ep93xx_spi_setup_dma(struct ep93xx_spi *espi)
dma_cap_set(DMA_SLAVE, mask);
espi->dma_rx_data.port = EP93XX_DMA_SSP;
espi->dma_rx_data.direction = DMA_FROM_DEVICE;
espi->dma_rx_data.direction = DMA_DEV_TO_MEM;
espi->dma_rx_data.name = "ep93xx-spi-rx";
espi->dma_rx = dma_request_channel(mask, ep93xx_spi_dma_filter,
......@@ -989,7 +992,7 @@ static int ep93xx_spi_setup_dma(struct ep93xx_spi *espi)
}
espi->dma_tx_data.port = EP93XX_DMA_SSP;
espi->dma_tx_data.direction = DMA_TO_DEVICE;
espi->dma_tx_data.direction = DMA_MEM_TO_DEV;
espi->dma_tx_data.name = "ep93xx-spi-tx";
espi->dma_tx = dma_request_channel(mask, ep93xx_spi_dma_filter,
......
......@@ -910,11 +910,11 @@ static int configure_dma(struct pl022 *pl022)
{
struct dma_slave_config rx_conf = {
.src_addr = SSP_DR(pl022->phybase),
.direction = DMA_FROM_DEVICE,
.direction = DMA_DEV_TO_MEM,
};
struct dma_slave_config tx_conf = {
.dst_addr = SSP_DR(pl022->phybase),
.direction = DMA_TO_DEVICE,
.direction = DMA_MEM_TO_DEV,
};
unsigned int pages;
int ret;
......@@ -1051,7 +1051,7 @@ static int configure_dma(struct pl022 *pl022)
rxdesc = rxchan->device->device_prep_slave_sg(rxchan,
pl022->sgt_rx.sgl,
rx_sglen,
DMA_FROM_DEVICE,
DMA_DEV_TO_MEM,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!rxdesc)
goto err_rxdesc;
......@@ -1059,7 +1059,7 @@ static int configure_dma(struct pl022 *pl022)
txdesc = txchan->device->device_prep_slave_sg(txchan,
pl022->sgt_tx.sgl,
tx_sglen,
DMA_TO_DEVICE,
DMA_MEM_TO_DEV,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!txdesc)
goto err_txdesc;
......
......@@ -1051,7 +1051,7 @@ static void pch_spi_handle_dma(struct pch_spi_data *data, int *bpw)
}
sg = dma->sg_rx_p;
desc_rx = dma->chan_rx->device->device_prep_slave_sg(dma->chan_rx, sg,
num, DMA_FROM_DEVICE,
num, DMA_DEV_TO_MEM,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!desc_rx) {
dev_err(&data->master->dev, "%s:device_prep_slave_sg Failed\n",
......@@ -1086,7 +1086,7 @@ static void pch_spi_handle_dma(struct pch_spi_data *data, int *bpw)
}
sg = dma->sg_tx_p;
desc_tx = dma->chan_tx->device->device_prep_slave_sg(dma->chan_tx,
sg, num, DMA_TO_DEVICE,
sg, num, DMA_MEM_TO_DEV,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!desc_tx) {
dev_err(&data->master->dev, "%s:device_prep_slave_sg Failed\n",
......
......@@ -268,7 +268,7 @@ static void pl011_dma_probe_initcall(struct uart_amba_port *uap)
struct dma_slave_config tx_conf = {
.dst_addr = uap->port.mapbase + UART01x_DR,
.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE,
.direction = DMA_TO_DEVICE,
.direction = DMA_MEM_TO_DEV,
.dst_maxburst = uap->fifosize >> 1,
};
struct dma_chan *chan;
......@@ -301,7 +301,7 @@ static void pl011_dma_probe_initcall(struct uart_amba_port *uap)
struct dma_slave_config rx_conf = {
.src_addr = uap->port.mapbase + UART01x_DR,
.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE,
.direction = DMA_FROM_DEVICE,
.direction = DMA_DEV_TO_MEM,
.src_maxburst = uap->fifosize >> 1,
};
......@@ -480,7 +480,7 @@ static int pl011_dma_tx_refill(struct uart_amba_port *uap)
return -EBUSY;
}
desc = dma_dev->device_prep_slave_sg(chan, &dmatx->sg, 1, DMA_TO_DEVICE,
desc = dma_dev->device_prep_slave_sg(chan, &dmatx->sg, 1, DMA_MEM_TO_DEV,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!desc) {
dma_unmap_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE);
......@@ -676,7 +676,7 @@ static int pl011_dma_rx_trigger_dma(struct uart_amba_port *uap)
&uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a;
dma_dev = rxchan->device;
desc = rxchan->device->device_prep_slave_sg(rxchan, &sgbuf->sg, 1,
DMA_FROM_DEVICE,
DMA_DEV_TO_MEM,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
/*
* If the DMA engine is busy and cannot prepare a
......
......@@ -747,7 +747,7 @@ static int dma_handle_rx(struct eg20t_port *priv)
sg_dma_address(sg) = priv->rx_buf_dma;
desc = priv->chan_rx->device->device_prep_slave_sg(priv->chan_rx,
sg, 1, DMA_FROM_DEVICE,
sg, 1, DMA_DEV_TO_MEM,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!desc)
......@@ -906,7 +906,7 @@ static unsigned int dma_handle_tx(struct eg20t_port *priv)
}
desc = priv->chan_tx->device->device_prep_slave_sg(priv->chan_tx,
priv->sg_tx_p, nent, DMA_TO_DEVICE,
priv->sg_tx_p, nent, DMA_MEM_TO_DEV,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!desc) {
dev_err(priv->port.dev, "%s:device_prep_slave_sg Failed\n",
......
......@@ -1207,7 +1207,7 @@ static void sci_submit_rx(struct sci_port *s)
struct dma_async_tx_descriptor *desc;
desc = chan->device->device_prep_slave_sg(chan,
sg, 1, DMA_FROM_DEVICE, DMA_PREP_INTERRUPT);
sg, 1, DMA_DEV_TO_MEM, DMA_PREP_INTERRUPT);
if (desc) {
s->desc_rx[i] = desc;
......@@ -1322,7 +1322,7 @@ static void work_fn_tx(struct work_struct *work)
BUG_ON(!sg_dma_len(sg));
desc = chan->device->device_prep_slave_sg(chan,
sg, s->sg_len_tx, DMA_TO_DEVICE,
sg, s->sg_len_tx, DMA_MEM_TO_DEV,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!desc) {
/* switch to PIO */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册