提交 864fdf88 编写于 作者: A Anton Vorontsov 提交者: David S. Miller

ucc_geth: Fix hangs after switching from full to half duplex

MPC8360 QE UCC ethernet controllers hang when changing link duplex
under a load (a bit of NFS activity is enough).

  PHY: mdio@e0102120:00 - Link is Up - 1000/Full
  sh-3.00# ethtool -s eth0 speed 100 duplex half autoneg off
  PHY: mdio@e0102120:00 - Link is Down
  PHY: mdio@e0102120:00 - Link is Up - 100/Half
  NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out
  ------------[ cut here ]------------
  Badness at c01fcbd0 [verbose debug info unavailable]
  NIP: c01fcbd0 LR: c01fcbd0 CTR: c0194e44
  ...

The cure is to disable the controller before changing speed/duplex
and enable it afterwards.

Though, disabling the controller might take quite a while, so we
better not grab any spinlocks in adjust_link(). Instead, we quiesce
the driver's activity, and only then disable the controller.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 7de8ee78
......@@ -1561,6 +1561,25 @@ static int ugeth_disable(struct ucc_geth_private *ugeth, enum comm_dir mode)
return 0;
}
static void ugeth_quiesce(struct ucc_geth_private *ugeth)
{
/* Wait for and prevent any further xmits. */
netif_tx_disable(ugeth->ndev);
/* Disable the interrupt to avoid NAPI rescheduling. */
disable_irq(ugeth->ug_info->uf_info.irq);
/* Stop NAPI, and possibly wait for its completion. */
napi_disable(&ugeth->napi);
}
static void ugeth_activate(struct ucc_geth_private *ugeth)
{
napi_enable(&ugeth->napi);
enable_irq(ugeth->ug_info->uf_info.irq);
netif_tx_wake_all_queues(ugeth->ndev);
}
/* Called every time the controller might need to be made
* aware of new link state. The PHY code conveys this
* information through variables in the ugeth structure, and this
......@@ -1574,14 +1593,11 @@ static void adjust_link(struct net_device *dev)
struct ucc_geth __iomem *ug_regs;
struct ucc_fast __iomem *uf_regs;
struct phy_device *phydev = ugeth->phydev;
unsigned long flags;
int new_state = 0;
ug_regs = ugeth->ug_regs;
uf_regs = ugeth->uccf->uf_regs;
spin_lock_irqsave(&ugeth->lock, flags);
if (phydev->link) {
u32 tempval = in_be32(&ug_regs->maccfg2);
u32 upsmr = in_be32(&uf_regs->upsmr);
......@@ -1632,9 +1648,21 @@ static void adjust_link(struct net_device *dev)
ugeth->oldspeed = phydev->speed;
}
/*
* To change the MAC configuration we need to disable the
* controller. To do so, we have to either grab ugeth->lock,
* which is a bad idea since 'graceful stop' commands might
* take quite a while, or we can quiesce driver's activity.
*/
ugeth_quiesce(ugeth);
ugeth_disable(ugeth, COMM_DIR_RX_AND_TX);
out_be32(&ug_regs->maccfg2, tempval);
out_be32(&uf_regs->upsmr, upsmr);
ugeth_enable(ugeth, COMM_DIR_RX_AND_TX);
ugeth_activate(ugeth);
if (!ugeth->oldlink) {
new_state = 1;
ugeth->oldlink = 1;
......@@ -1648,8 +1676,6 @@ static void adjust_link(struct net_device *dev)
if (new_state && netif_msg_link(ugeth))
phy_print_status(phydev);
spin_unlock_irqrestore(&ugeth->lock, flags);
}
/* Initialize TBI PHY interface for communicating with the
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册