Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
  net: clear heap allocation for ETHTOOL_GRXCLSRLALL
  isdn: strcpy() => strlcpy()
  Revert "mac80211: use netif_receive_skb in ieee80211_tx_status callpath"
  mac80211: delete AddBA response timer
  ath9k_hw: fix regression in ANI listen time calculation
  caif: fix two caif_connect() bugs
  bonding: fix WARN_ON when writing to bond_master sysfs file
  skge: add quirk to limit DMA
  MAINTAINERS: update Intel LAN Ethernet info
  e1000e.txt: Add e1000e documentation
  e1000.txt: Update e1000 documentation
  ixgbevf.txt: Update ixgbevf documentation
  cls_u32: signedness bug
  Bluetooth: Disallow to change L2CAP_OPTIONS values when connected
  sctp: Fix out-of-bounds reading in sctp_asoc_get_hmac()
  sctp: prevent reading out-of-bounds memory
  ipv4: correct IGMP behavior on v3 query during v2-compatibility mode
  netdev: Depend on INET before selecting INET_LRO
  Revert "ipv4: Make INET_LRO a bool instead of tristate."
  net: Fix the condition passed to sk_wait_event()
  ...

Documentation/networking/e1000e.txt

+Linux* Driver for Intel(R) Network Connection
+===============================================================
+
+Intel Gigabit Linux driver.
+Copyright(c) 1999 - 2010 Intel Corporation.
+
+Contents
+========
+
+- Identifying Your Adapter
+- Command Line Parameters
+- Additional Configurations
+- Support
+
+Identifying Your Adapter
+========================
+
+The e1000e driver supports all PCI Express Intel(R) Gigabit Network
+Connections, except those that are 82575, 82576 and 82580-based*.
+
+* NOTE: The Intel(R) PRO/1000 P Dual Port Server Adapter is supported by
+  the e1000 driver, not the e1000e driver due to the 82546 part being used
+  behind a PCI Express bridge.
+
+For more information on how to identify your adapter, go to the Adapter &
+Driver ID Guide at:
+
+    http://support.intel.com/support/go/network/adapter/idguide.htm
+
+For the latest Intel network drivers for Linux, refer to the following
+website.  In the search field, enter your adapter name or type, or use the
+networking link on the left to search for your adapter:
+
+    http://support.intel.com/support/go/network/adapter/home.htm
+
+Command Line Parameters
+=======================
+
+The default value for each parameter is generally the recommended setting,
+unless otherwise noted.
+
+NOTES:  For more information about the InterruptThrottleRate,
+        RxIntDelay, TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay
+        parameters, see the application note at:
+        http://www.intel.com/design/network/applnots/ap450.htm
+
+InterruptThrottleRate
+---------------------
+Valid Range:   0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative,
+                                   4=simplified balancing)
+Default Value: 3
+
+The driver can limit the amount of interrupts per second that the adapter
+will generate for incoming packets. It does this by writing a value to the
+adapter that is based on the maximum amount of interrupts that the adapter
+will generate per second.
+
+Setting InterruptThrottleRate to a value greater or equal to 100
+will program the adapter to send out a maximum of that many interrupts
+per second, even if more packets have come in. This reduces interrupt
+load on the system and can lower CPU utilization under heavy load,
+but will increase latency as packets are not processed as quickly.
+
+The driver has two adaptive modes (setting 1 or 3) in which
+it dynamically adjusts the InterruptThrottleRate value based on the traffic
+that it receives. After determining the type of incoming traffic in the last
+timeframe, it will adjust the InterruptThrottleRate to an appropriate value
+for that traffic.
+
+The algorithm classifies the incoming traffic every interval into
+classes.  Once the class is determined, the InterruptThrottleRate value is
+adjusted to suit that traffic type the best. There are three classes defined:
+"Bulk traffic", for large amounts of packets of normal size; "Low latency",
+for small amounts of traffic and/or a significant percentage of small
+packets; and "Lowest latency", for almost completely small packets or
+minimal traffic.
+
+In dynamic conservative mode, the InterruptThrottleRate value is set to 4000
+for traffic that falls in class "Bulk traffic". If traffic falls in the "Low
+latency" or "Lowest latency" class, the InterruptThrottleRate is increased
+stepwise to 20000. This default mode is suitable for most applications.
+
+For situations where low latency is vital such as cluster or
+grid computing, the algorithm can reduce latency even more when
+InterruptThrottleRate is set to mode 1. In this mode, which operates
+the same as mode 3, the InterruptThrottleRate will be increased stepwise to
+70000 for traffic in class "Lowest latency".
+
+In simplified mode the interrupt rate is based on the ratio of Tx and
+Rx traffic.  If the bytes per second rate is approximately equal the
+interrupt rate will drop as low as 2000 interrupts per second.  If the
+traffic is mostly transmit or mostly receive, the interrupt rate could
+be as high as 8000.
+
+Setting InterruptThrottleRate to 0 turns off any interrupt moderation
+and may improve small packet latency, but is generally not suitable
+for bulk throughput traffic.
+
+NOTE:  InterruptThrottleRate takes precedence over the TxAbsIntDelay and
+       RxAbsIntDelay parameters.  In other words, minimizing the receive
+       and/or transmit absolute delays does not force the controller to
+       generate more interrupts than what the Interrupt Throttle Rate
+       allows.
+
+NOTE:  When e1000e is loaded with default settings and multiple adapters
+       are in use simultaneously, the CPU utilization may increase non-
+       linearly.  In order to limit the CPU utilization without impacting
+       the overall throughput, we recommend that you load the driver as
+       follows:
+
+           modprobe e1000e InterruptThrottleRate=3000,3000,3000
+
+       This sets the InterruptThrottleRate to 3000 interrupts/sec for
+       the first, second, and third instances of the driver.  The range
+       of 2000 to 3000 interrupts per second works on a majority of
+       systems and is a good starting point, but the optimal value will
+       be platform-specific.  If CPU utilization is not a concern, use
+       RX_POLLING (NAPI) and default driver settings.
+
+RxIntDelay
+----------
+Valid Range:   0-65535 (0=off)
+Default Value: 0
+
+This value delays the generation of receive interrupts in units of 1.024
+microseconds.  Receive interrupt reduction can improve CPU efficiency if
+properly tuned for specific network traffic.  Increasing this value adds
+extra latency to frame reception and can end up decreasing the throughput
+of TCP traffic.  If the system is reporting dropped receives, this value
+may be set too high, causing the driver to run out of available receive
+descriptors.
+
+CAUTION:  When setting RxIntDelay to a value other than 0, adapters may
+          hang (stop transmitting) under certain network conditions.  If
+          this occurs a NETDEV WATCHDOG message is logged in the system
+          event log.  In addition, the controller is automatically reset,
+          restoring the network connection.  To eliminate the potential
+          for the hang ensure that RxIntDelay is set to 0.
+
+RxAbsIntDelay
+-------------
+Valid Range:   0-65535 (0=off)
+Default Value: 8
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+receive interrupt is generated.  Useful only if RxIntDelay is non-zero,
+this value ensures that an interrupt is generated after the initial
+packet is received within the set amount of time.  Proper tuning,
+along with RxIntDelay, may improve traffic throughput in specific network
+conditions.
+
+TxIntDelay
+----------
+Valid Range:   0-65535 (0=off)
+Default Value: 8
+
+This value delays the generation of transmit interrupts in units of
+1.024 microseconds.  Transmit interrupt reduction can improve CPU
+efficiency if properly tuned for specific network traffic.  If the
+system is reporting dropped transmits, this value may be set too high
+causing the driver to run out of available transmit descriptors.
+
+TxAbsIntDelay
+-------------
+Valid Range:   0-65535 (0=off)
+Default Value: 32
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+transmit interrupt is generated.  Useful only if TxIntDelay is non-zero,
+this value ensures that an interrupt is generated after the initial
+packet is sent on the wire within the set amount of time.  Proper tuning,
+along with TxIntDelay, may improve traffic throughput in specific
+network conditions.
+
+Copybreak
+---------
+Valid Range:   0-xxxxxxx (0=off)
+Default Value: 256
+
+Driver copies all packets below or equaling this size to a fresh Rx
+buffer before handing it up the stack.
+
+This parameter is different than other parameters, in that it is a
+single (not 1,1,1 etc.) parameter applied to all driver instances and
+it is also available during runtime at
+/sys/module/e1000e/parameters/copybreak
+
+SmartPowerDownEnable
+--------------------
+Valid Range: 0-1
+Default Value:  0 (disabled)
+
+Allows PHY to turn off in lower power states. The user can set this parameter
+in supported chipsets.
+
+KumeranLockLoss
+---------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+This workaround skips resetting the PHY at shutdown for the initial
+silicon releases of ICH8 systems.
+
+IntMode
+-------
+Valid Range: 0-2 (0=legacy, 1=MSI, 2=MSI-X)
+Default Value: 2
+
+Allows changing the interrupt mode at module load time, without requiring a
+recompile. If the driver load fails to enable a specific interrupt mode, the
+driver will try other interrupt modes, from least to most compatible.  The
+interrupt order is MSI-X, MSI, Legacy.  If specifying MSI (IntMode=1)
+interrupts, only MSI and Legacy will be attempted.
+
+CrcStripping
+------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+Strip the CRC from received packets before sending up the network stack.  If
+you have a machine with a BMC enabled but cannot receive IPMI traffic after
+loading or enabling the driver, try disabling this feature.
+
+WriteProtectNVM
+---------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+Set the hardware to ignore all write/erase cycles to the GbE region in the
+ICHx NVM (non-volatile memory).  This feature can be disabled by the
+WriteProtectNVM module parameter (enabled by default) only after a hardware
+reset, but the machine must be power cycled before trying to enable writes.
+
+Note: the kernel boot option iomem=relaxed may need to be set if the kernel
+config option CONFIG_STRICT_DEVMEM=y, if the root user wants to write the
+NVM from user space via ethtool.
+
+Additional Configurations
+=========================
+
+  Jumbo Frames
+  ------------
+  Jumbo Frames support is enabled by changing the MTU to a value larger than
+  the default of 1500.  Use the ifconfig command to increase the MTU size.
+  For example:
+
+       ifconfig eth<x> mtu 9000 up
+
+  This setting is not saved across reboots.
+
+  Notes:
+
+  - The maximum MTU setting for Jumbo Frames is 9216.  This value coincides
+    with the maximum Jumbo Frames size of 9234 bytes.
+
+  - Using Jumbo Frames at 10 or 100 Mbps is not supported and may result in
+    poor performance or loss of link.
+
+  - Some adapters limit Jumbo Frames sized packets to a maximum of
+    4096 bytes and some adapters do not support Jumbo Frames.
+
+
+  Ethtool
+  -------
+  The driver utilizes the ethtool interface for driver configuration and
+  diagnostics, as well as displaying statistical information.  We
+  strongly recommend downloading the latest version of Ethtool at:
+
+  http://sourceforge.net/projects/gkernel.
+
+  Speed and Duplex
+  ----------------
+  Speed and Duplex are configured through the Ethtool* utility. For
+  instructions,  refer to the Ethtool man page.
+
+  Enabling Wake on LAN* (WoL)
+  ---------------------------
+  WoL is configured through the Ethtool* utility. For instructions on
+  enabling WoL with Ethtool, refer to the Ethtool man page.
+
+  WoL will be enabled on the system during the next shut down or reboot.
+  For this driver version, in order to enable WoL, the e1000e driver must be
+  loaded when shutting down or rebooting the system.
+
+  In most cases Wake On LAN is only supported on port A for multiple port
+  adapters. To verify if a port supports Wake on LAN run ethtool eth<X>.
+
+
+Support
+=======
+
+For general information, go to the Intel support website at:
+
+    www.intel.com/support/
+
+or the Intel Wired Networking project hosted by Sourceforge at:
+
+    http://sourceforge.net/projects/e1000
+
+If an issue is identified with the released source code on the supported
+kernel with a supported adapter, email the specific information related
+to the issue to e1000-devel@lists.sf.net

Documentation/networking/ixgbevf.txt

 Linux* Base Driver for Intel(R) Network Connection
 ==================================================
 
-November 24, 2009
+Intel Gigabit Linux driver.
+Copyright(c) 1999 - 2010 Intel Corporation.
 
 Contents
 ========
 
-- In This Release
 - Identifying Your Adapter
 - Known Issues/Troubleshooting
 - Support
 
-In This Release
-===============
-
 This file describes the ixgbevf Linux* Base Driver for Intel Network
 Connection.
 
@@ -33,7 +30,7 @@ Identifying Your Adapter
 For more information on how to identify your adapter, go to the Adapter &
 Driver ID Guide at:
 
-    http://support.intel.com/support/network/sb/CS-008441.htm
+    http://support.intel.com/support/go/network/adapter/idguide.htm
 
 Known Issues/Troubleshooting
 ============================
@@ -57,34 +54,3 @@ or the Intel Wired Networking project hosted by Sourceforge at:
 If an issue is identified with the released source code on the supported
 kernel with a supported adapter, email the specific information related
 to the issue to e1000-devel@lists.sf.net
-
-License
-=======
-
-Intel 10 Gigabit Linux driver.
-Copyright(c) 1999 - 2009 Intel Corporation.
-
-This program is free software; you can redistribute it and/or modify it
-under the terms and conditions of the GNU General Public License,
-version 2, as published by the Free Software Foundation.
-
-This program is distributed in the hope it will be useful, but WITHOUT
-ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
-more details.
-
-You should have received a copy of the GNU General Public License along with
-this program; if not, write to the Free Software Foundation, Inc.,
-51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
-
-The full GNU General Public License is included in this distribution in
-the file called "COPYING".
-
-Trademarks
-==========
-
-Intel, Itanium, and Pentium are trademarks or registered trademarks of
-Intel Corporation or its subsidiaries in the United States and other
-countries.
-
-* Other names and brands may be claimed as the property of others.

MAINTAINERS

@@ -3073,16 +3073,27 @@ L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/ixp2000/
 
-INTEL ETHERNET DRIVERS (e100/e1000/e1000e/igb/igbvf/ixgb/ixgbe)
+INTEL ETHERNET DRIVERS (e100/e1000/e1000e/igb/igbvf/ixgb/ixgbe/ixgbevf)
 M:	Jeff Kirsher <jeffrey.t.kirsher@intel.com>
 M:	Jesse Brandeburg <jesse.brandeburg@intel.com>
 M:	Bruce Allan <bruce.w.allan@intel.com>
-M:	Alex Duyck <alexander.h.duyck@intel.com>
+M:	Carolyn Wyborny <carolyn.wyborny@intel.com>
+M:	Don Skidmore <donald.c.skidmore@intel.com>
+M:	Greg Rose <gregory.v.rose@intel.com>
 M:	PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
+M:	Alex Duyck <alexander.h.duyck@intel.com>
 M:	John Ronciak <john.ronciak@intel.com>
 L:	e1000-devel@lists.sourceforge.net
 W:	http://e1000.sourceforge.net/
 S:	Supported
+F:	Documentation/networking/e100.txt
+F:	Documentation/networking/e1000.txt
+F:	Documentation/networking/e1000e.txt
+F:	Documentation/networking/igb.txt
+F:	Documentation/networking/igbvf.txt
+F:	Documentation/networking/ixgb.txt
+F:	Documentation/networking/ixgbe.txt
+F:	Documentation/networking/ixgbevf.txt
 F:	drivers/net/e100.c
 F:	drivers/net/e1000/
 F:	drivers/net/e1000e/
@@ -3090,6 +3101,7 @@ F:	drivers/net/igb/
 F:	drivers/net/igbvf/
 F:	drivers/net/ixgb/
 F:	drivers/net/ixgbe/
+F:	drivers/net/ixgbevf/
 
 INTEL PRO/WIRELESS 2100 NETWORK CONNECTION SUPPORT
 L:	linux-wireless@vger.kernel.org

drivers/isdn/sc/interrupt.c

@@ -112,11 +112,19 @@ irqreturn_t interrupt_handler(int dummy, void *card_inst)
 			}
 			else if(callid>=0x0000 && callid<=0x7FFF)
 			{
+				int len;
+
 				pr_debug("%s: Got Incoming Call\n",
 						sc_adapter[card]->devicename);
-				strcpy(setup.phone,&(rcvmsg.msg_data.byte_array[4]));
-				strcpy(setup.eazmsn,
-					sc_adapter[card]->channel[rcvmsg.phy_link_no-1].dn);
+				len = strlcpy(setup.phone, &(rcvmsg.msg_data.byte_array[4]),
+						sizeof(setup.phone));
+				if (len >= sizeof(setup.phone))
+					continue;
+				len = strlcpy(setup.eazmsn,
+						sc_adapter[card]->channel[rcvmsg.phy_link_no - 1].dn,
+						sizeof(setup.eazmsn));
+				if (len >= sizeof(setup.eazmsn))
+					continue;
 				setup.si1 = 7;
 				setup.si2 = 0;
 				setup.plan = 0;
@@ -176,7 +184,9 @@ irqreturn_t interrupt_handler(int dummy, void *card_inst)
 		 * Handle a GetMyNumber Rsp
 		 */
 		if (IS_CE_MESSAGE(rcvmsg,Call,0,GetMyNumber)){
-			strcpy(sc_adapter[card]->channel[rcvmsg.phy_link_no-1].dn,rcvmsg.msg_data.byte_array);
+			strlcpy(sc_adapter[card]->channel[rcvmsg.phy_link_no - 1].dn,
+				rcvmsg.msg_data.byte_array,
+				sizeof(rcvmsg.msg_data.byte_array));
 			continue;
 		}
 			

drivers/net/Kconfig

@@ -2428,7 +2428,7 @@ config UGETH_TX_ON_DEMAND
 
 config MV643XX_ETH
 	tristate "Marvell Discovery (643XX) and Orion ethernet support"
-	depends on MV64X60 || PPC32 || PLAT_ORION
+	depends on (MV64X60 || PPC32 || PLAT_ORION) && INET
 	select INET_LRO
 	select PHYLIB
 	help
@@ -2803,7 +2803,7 @@ config NIU
 
 config PASEMI_MAC
 	tristate "PA Semi 1/10Gbit MAC"
-	depends on PPC_PASEMI && PCI
+	depends on PPC_PASEMI && PCI && INET
 	select PHYLIB
 	select INET_LRO
 	help

drivers/net/bonding/bond_main.c

@@ -5164,6 +5164,15 @@ int bond_create(struct net *net, const char *name)
 		res = dev_alloc_name(bond_dev, "bond%d");
 		if (res < 0)
 			goto out;
+	} else {
+		/*
+		 * If we're given a name to register
+		 * we need to ensure that its not already
+		 * registered
+		 */
+		res = -EEXIST;
+		if (__dev_get_by_name(net, name) != NULL)
+			goto out;
 	}
 
 	res = register_netdevice(bond_dev);

drivers/net/skge.c

@@ -43,6 +43,7 @@
 #include <linux/seq_file.h>
 #include <linux/mii.h>
 #include <linux/slab.h>
+#include <linux/dmi.h>
 #include <asm/irq.h>
 
 #include "skge.h"
@@ -3868,6 +3869,8 @@ static void __devinit skge_show_addr(struct net_device *dev)
 	netif_info(skge, probe, skge->netdev, "addr %pM\n", dev->dev_addr);
 }
 
+static int only_32bit_dma;
+
 static int __devinit skge_probe(struct pci_dev *pdev,
 				const struct pci_device_id *ent)
 {
@@ -3889,7 +3892,7 @@ static int __devinit skge_probe(struct pci_dev *pdev,
 
 	pci_set_master(pdev);
 
-	if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
+	if (!only_32bit_dma && !pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
 		using_dac = 1;
 		err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
 	} else if (!(err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)))) {
@@ -4147,8 +4150,21 @@ static struct pci_driver skge_driver = {
 	.shutdown =	skge_shutdown,
 };
 
+static struct dmi_system_id skge_32bit_dma_boards[] = {
+	{
+		.ident = "Gigabyte nForce boards",
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Gigabyte Technology Co"),
+			DMI_MATCH(DMI_BOARD_NAME, "nForce"),
+		},
+	},
+	{}
+};
+
 static int __init skge_init_module(void)
 {
+	if (dmi_check_system(skge_32bit_dma_boards))
+		only_32bit_dma = 1;
 	skge_debug_init();
 	return pci_register_driver(&skge_driver);
 }

drivers/net/wireless/ath/ath9k/ani.c

@@ -543,7 +543,7 @@ static u8 ath9k_hw_chan_2_clockrate_mhz(struct ath_hw *ah)
 	if (conf_is_ht40(conf))
 		return clockrate * 2;
 
-	return clockrate * 2;
+	return clockrate;
 }
 
 static int32_t ath9k_hw_ani_get_listen_time(struct ath_hw *ah)

include/net/bluetooth/bluetooth.h

@@ -161,12 +161,30 @@ static inline struct sk_buff *bt_skb_send_alloc(struct sock *sk, unsigned long l
 {
 	struct sk_buff *skb;
 
+	release_sock(sk);
 	if ((skb = sock_alloc_send_skb(sk, len + BT_SKB_RESERVE, nb, err))) {
 		skb_reserve(skb, BT_SKB_RESERVE);
 		bt_cb(skb)->incoming  = 0;
 	}
+	lock_sock(sk);
+
+	if (!skb && *err)
+		return NULL;
+
+	*err = sock_error(sk);
+	if (*err)
+		goto out;
+
+	if (sk->sk_shutdown) {
+		*err = -ECONNRESET;
+		goto out;
+	}
 
 	return skb;
+
+out:
+	kfree_skb(skb);
+	return NULL;
 }
 
 int bt_err(__u16 code);

net/bluetooth/l2cap.c

@@ -1441,33 +1441,23 @@ static inline void l2cap_do_send(struct sock *sk, struct sk_buff *skb)
 
 static void l2cap_streaming_send(struct sock *sk)
 {
-	struct sk_buff *skb, *tx_skb;
+	struct sk_buff *skb;
 	struct l2cap_pinfo *pi = l2cap_pi(sk);
 	u16 control, fcs;
 
-	while ((skb = sk->sk_send_head)) {
-		tx_skb = skb_clone(skb, GFP_ATOMIC);
-
-		control = get_unaligned_le16(tx_skb->data + L2CAP_HDR_SIZE);
+	while ((skb = skb_dequeue(TX_QUEUE(sk)))) {
+		control = get_unaligned_le16(skb->data + L2CAP_HDR_SIZE);
 		control |= pi->next_tx_seq << L2CAP_CTRL_TXSEQ_SHIFT;
-		put_unaligned_le16(control, tx_skb->data + L2CAP_HDR_SIZE);
+		put_unaligned_le16(control, skb->data + L2CAP_HDR_SIZE);
 
 		if (pi->fcs == L2CAP_FCS_CRC16) {
-			fcs = crc16(0, (u8 *)tx_skb->data, tx_skb->len - 2);
-			put_unaligned_le16(fcs, tx_skb->data + tx_skb->len - 2);
+			fcs = crc16(0, (u8 *)skb->data, skb->len - 2);
+			put_unaligned_le16(fcs, skb->data + skb->len - 2);
 		}
 
-		l2cap_do_send(sk, tx_skb);
+		l2cap_do_send(sk, skb);
 
 		pi->next_tx_seq = (pi->next_tx_seq + 1) % 64;
-
-		if (skb_queue_is_last(TX_QUEUE(sk), skb))
-			sk->sk_send_head = NULL;
-		else
-			sk->sk_send_head = skb_queue_next(TX_QUEUE(sk), skb);
-
-		skb = skb_dequeue(TX_QUEUE(sk));
-		kfree_skb(skb);
 	}
 }
 
@@ -1960,6 +1950,11 @@ static int l2cap_sock_setsockopt_old(struct socket *sock, int optname, char __us
 
 	switch (optname) {
 	case L2CAP_OPTIONS:
+		if (sk->sk_state == BT_CONNECTED) {
+			err = -EINVAL;
+			break;
+		}
+
 		opts.imtu     = l2cap_pi(sk)->imtu;
 		opts.omtu     = l2cap_pi(sk)->omtu;
 		opts.flush_to = l2cap_pi(sk)->flush_to;
@@ -2771,10 +2766,10 @@ static int l2cap_parse_conf_rsp(struct sock *sk, void *rsp, int len, void *data,
 		case L2CAP_CONF_MTU:
 			if (val < L2CAP_DEFAULT_MIN_MTU) {
 				*result = L2CAP_CONF_UNACCEPT;
-				pi->omtu = L2CAP_DEFAULT_MIN_MTU;
+				pi->imtu = L2CAP_DEFAULT_MIN_MTU;
 			} else
-				pi->omtu = val;
-			l2cap_add_conf_opt(&ptr, L2CAP_CONF_MTU, 2, pi->omtu);
+				pi->imtu = val;
+			l2cap_add_conf_opt(&ptr, L2CAP_CONF_MTU, 2, pi->imtu);
 			break;
 
 		case L2CAP_CONF_FLUSH_TO:
@@ -3071,6 +3066,17 @@ static inline int l2cap_connect_rsp(struct l2cap_conn *conn, struct l2cap_cmd_hd
 	return 0;
 }
 
+static inline void set_default_fcs(struct l2cap_pinfo *pi)
+{
+	/* FCS is enabled only in ERTM or streaming mode, if one or both
+	 * sides request it.
+	 */
+	if (pi->mode != L2CAP_MODE_ERTM && pi->mode != L2CAP_MODE_STREAMING)
+		pi->fcs = L2CAP_FCS_NONE;
+	else if (!(pi->conf_state & L2CAP_CONF_NO_FCS_RECV))
+		pi->fcs = L2CAP_FCS_CRC16;
+}
+
 static inline int l2cap_config_req(struct l2cap_conn *conn, struct l2cap_cmd_hdr *cmd, u16 cmd_len, u8 *data)
 {
 	struct l2cap_conf_req *req = (struct l2cap_conf_req *) data;
@@ -3088,14 +3094,8 @@ static inline int l2cap_config_req(struct l2cap_conn *conn, struct l2cap_cmd_hdr
 	if (!sk)
 		return -ENOENT;
 
-	if (sk->sk_state != BT_CONFIG) {
-		struct l2cap_cmd_rej rej;
-
-		rej.reason = cpu_to_le16(0x0002);
-		l2cap_send_cmd(conn, cmd->ident, L2CAP_COMMAND_REJ,
-				sizeof(rej), &rej);
+	if (sk->sk_state == BT_DISCONN)
 		goto unlock;
-	}
 
 	/* Reject if config buffer is too small. */
 	len = cmd_len - sizeof(*req);
@@ -3135,9 +3135,7 @@ static inline int l2cap_config_req(struct l2cap_conn *conn, struct l2cap_cmd_hdr
 		goto unlock;
 
 	if (l2cap_pi(sk)->conf_state & L2CAP_CONF_INPUT_DONE) {
-		if (!(l2cap_pi(sk)->conf_state & L2CAP_CONF_NO_FCS_RECV) ||
-		    l2cap_pi(sk)->fcs != L2CAP_FCS_NONE)
-			l2cap_pi(sk)->fcs = L2CAP_FCS_CRC16;
+		set_default_fcs(l2cap_pi(sk));
 
 		sk->sk_state = BT_CONNECTED;
 
@@ -3225,9 +3223,7 @@ static inline int l2cap_config_rsp(struct l2cap_conn *conn, struct l2cap_cmd_hdr
 	l2cap_pi(sk)->conf_state |= L2CAP_CONF_INPUT_DONE;
 
 	if (l2cap_pi(sk)->conf_state & L2CAP_CONF_OUTPUT_DONE) {
-		if (!(l2cap_pi(sk)->conf_state & L2CAP_CONF_NO_FCS_RECV) ||
-		    l2cap_pi(sk)->fcs != L2CAP_FCS_NONE)
-			l2cap_pi(sk)->fcs = L2CAP_FCS_CRC16;
+		set_default_fcs(l2cap_pi(sk));
 
 		sk->sk_state = BT_CONNECTED;
 		l2cap_pi(sk)->next_tx_seq = 0;

net/bluetooth/rfcomm/sock.c

@@ -82,11 +82,14 @@ static void rfcomm_sk_data_ready(struct rfcomm_dlc *d, struct sk_buff *skb)
 static void rfcomm_sk_state_change(struct rfcomm_dlc *d, int err)
 {
 	struct sock *sk = d->owner, *parent;
+	unsigned long flags;
+
 	if (!sk)
 		return;
 
 	BT_DBG("dlc %p state %ld err %d", d, d->state, err);
 
+	local_irq_save(flags);
 	bh_lock_sock(sk);
 
 	if (err)
@@ -108,6 +111,7 @@ static void rfcomm_sk_state_change(struct rfcomm_dlc *d, int err)
 	}
 
 	bh_unlock_sock(sk);
+	local_irq_restore(flags);
 
 	if (parent && sock_flag(sk, SOCK_ZAPPED)) {
 		/* We have to drop DLC lock here, otherwise

net/caif/caif_socket.c

@@ -827,6 +827,7 @@ static int caif_connect(struct socket *sock, struct sockaddr *uaddr,
 	long timeo;
 	int err;
 	int ifindex, headroom, tailroom;
+	unsigned int mtu;
 	struct net_device *dev;
 
 	lock_sock(sk);
@@ -896,15 +897,23 @@ static int caif_connect(struct socket *sock, struct sockaddr *uaddr,
 		cf_sk->sk.sk_state = CAIF_DISCONNECTED;
 		goto out;
 	}
-	dev = dev_get_by_index(sock_net(sk), ifindex);
+
+	err = -ENODEV;
+	rcu_read_lock();
+	dev = dev_get_by_index_rcu(sock_net(sk), ifindex);
+	if (!dev) {
+		rcu_read_unlock();
+		goto out;
+	}
 	cf_sk->headroom = LL_RESERVED_SPACE_EXTRA(dev, headroom);
+	mtu = dev->mtu;
+	rcu_read_unlock();
+
 	cf_sk->tailroom = tailroom;
-	cf_sk->maxframe = dev->mtu - (headroom + tailroom);
-	dev_put(dev);
+	cf_sk->maxframe = mtu - (headroom + tailroom);
 	if (cf_sk->maxframe < 1) {
-		pr_warning("CAIF: %s(): CAIF Interface MTU too small (%d)\n",
-			__func__, dev->mtu);
-		err = -ENODEV;
+		pr_warning("CAIF: %s(): CAIF Interface MTU too small (%u)\n",
+			   __func__, mtu);
 		goto out;
 	}
 

net/core/ethtool.c

@@ -348,7 +348,7 @@ static noinline_for_stack int ethtool_get_rxnfc(struct net_device *dev,
 	if (info.cmd == ETHTOOL_GRXCLSRLALL) {
 		if (info.rule_cnt > 0) {
 			if (info.rule_cnt <= KMALLOC_MAX_SIZE / sizeof(u32))
-				rule_buf = kmalloc(info.rule_cnt * sizeof(u32),
+				rule_buf = kzalloc(info.rule_cnt * sizeof(u32),
 						   GFP_USER);
 			if (!rule_buf)
 				return -ENOMEM;

net/core/stream.c

@@ -141,10 +141,10 @@ int sk_stream_wait_memory(struct sock *sk, long *timeo_p)
 
 		set_bit(SOCK_NOSPACE, &sk->sk_socket->flags);
 		sk->sk_write_pending++;
-		sk_wait_event(sk, &current_timeo, !sk->sk_err &&
-						  !(sk->sk_shutdown & SEND_SHUTDOWN) &&
-						  sk_stream_memory_free(sk) &&
-						  vm_wait);
+		sk_wait_event(sk, &current_timeo, sk->sk_err ||
+						  (sk->sk_shutdown & SEND_SHUTDOWN) ||
+						  (sk_stream_memory_free(sk) &&
+						  !vm_wait));
 		sk->sk_write_pending--;
 
 		if (vm_wait) {

net/ipv4/Kconfig

@@ -413,7 +413,7 @@ config INET_XFRM_MODE_BEET
 	  If unsure, say Y.
 
 config INET_LRO
-	bool "Large Receive Offload (ipv4/tcp)"
+	tristate "Large Receive Offload (ipv4/tcp)"
 	default y
 	---help---
 	  Support for Large Receive Offload (ipv4/tcp).

net/ipv4/igmp.c

@@ -834,7 +834,7 @@ static void igmp_heard_query(struct in_device *in_dev, struct sk_buff *skb,
 	int			mark = 0;
 
 
-	if (len == 8 || IGMP_V2_SEEN(in_dev)) {
+	if (len == 8) {
 		if (ih->code == 0) {
 			/* Alas, old v1 router presents here. */
 
@@ -856,6 +856,18 @@ static void igmp_heard_query(struct in_device *in_dev, struct sk_buff *skb,
 		igmpv3_clear_delrec(in_dev);
 	} else if (len < 12) {
 		return;	/* ignore bogus packet; freed by caller */
+	} else if (IGMP_V1_SEEN(in_dev)) {
+		/* This is a v3 query with v1 queriers present */
+		max_delay = IGMP_Query_Response_Interval;
+		group = 0;
+	} else if (IGMP_V2_SEEN(in_dev)) {
+		/* this is a v3 query with v2 queriers present;
+		 * Interpretation of the max_delay code is problematic here.
+		 * A real v2 host would use ih_code directly, while v3 has a
+		 * different encoding. We use the v3 encoding as more likely
+		 * to be intended in a v3 query.
+		 */
+		max_delay = IGMPV3_MRC(ih3->code)*(HZ/IGMP_TIMER_SCALE);
 	} else { /* v3 */
 		if (!pskb_may_pull(skb, sizeof(struct igmpv3_query)))
 			return;

net/ipv6/route.c

@@ -1556,14 +1556,13 @@ void rt6_redirect(struct in6_addr *dest, struct in6_addr *src,
  *	i.e. Path MTU discovery
  */
 
-void rt6_pmtu_discovery(struct in6_addr *daddr, struct in6_addr *saddr,
-			struct net_device *dev, u32 pmtu)
+static void rt6_do_pmtu_disc(struct in6_addr *daddr, struct in6_addr *saddr,
+			     struct net *net, u32 pmtu, int ifindex)
 {
 	struct rt6_info *rt, *nrt;
-	struct net *net = dev_net(dev);
 	int allfrag = 0;
 
-	rt = rt6_lookup(net, daddr, saddr, dev->ifindex, 0);
+	rt = rt6_lookup(net, daddr, saddr, ifindex, 0);
 	if (rt == NULL)
 		return;
 
@@ -1631,6 +1630,27 @@ void rt6_pmtu_discovery(struct in6_addr *daddr, struct in6_addr *saddr,
 	dst_release(&rt->dst);
 }
 
+void rt6_pmtu_discovery(struct in6_addr *daddr, struct in6_addr *saddr,
+			struct net_device *dev, u32 pmtu)
+{
+	struct net *net = dev_net(dev);
+
+	/*
+	 * RFC 1981 states that a node "MUST reduce the size of the packets it
+	 * is sending along the path" that caused the Packet Too Big message.
+	 * Since it's not possible in the general case to determine which
+	 * interface was used to send the original packet, we update the MTU
+	 * on the interface that will be used to send future packets. We also
+	 * update the MTU on the interface that received the Packet Too Big in
+	 * case the original packet was forced out that interface with
+	 * SO_BINDTODEVICE or similar. This is the next best thing to the
+	 * correct behaviour, which would be to update the MTU on all
+	 * interfaces.
+	 */
+	rt6_do_pmtu_disc(daddr, saddr, net, pmtu, 0);
+	rt6_do_pmtu_disc(daddr, saddr, net, pmtu, dev->ifindex);
+}
+
 /*
  *	Misc support functions
  */

net/mac80211/agg-tx.c

@@ -175,6 +175,8 @@ int ___ieee80211_stop_tx_ba_session(struct sta_info *sta, u16 tid,
 
 	set_bit(HT_AGG_STATE_STOPPING, &tid_tx->state);
 
+	del_timer_sync(&tid_tx->addba_resp_timer);
+
 	/*
 	 * After this packets are no longer handed right through
 	 * to the driver but are put onto tid_tx->pending instead,

net/mac80211/status.c

@@ -377,7 +377,7 @@ void ieee80211_tx_status(struct ieee80211_hw *hw, struct sk_buff *skb)
 				skb2 = skb_clone(skb, GFP_ATOMIC);
 				if (skb2) {
 					skb2->dev = prev_dev;
-					netif_receive_skb(skb2);
+					netif_rx(skb2);
 				}
 			}
 
@@ -386,7 +386,7 @@ void ieee80211_tx_status(struct ieee80211_hw *hw, struct sk_buff *skb)
 	}
 	if (prev_dev) {
 		skb->dev = prev_dev;
-		netif_receive_skb(skb);
+		netif_rx(skb);
 		skb = NULL;
 	}
 	rcu_read_unlock();

net/sched/cls_u32.c

@@ -137,7 +137,7 @@ static int u32_classify(struct sk_buff *skb, struct tcf_proto *tp, struct tcf_re
 			int toff = off + key->off + (off2 & key->offmask);
 			__be32 *data, _data;
 
-			if (skb_headroom(skb) + toff < 0)
+			if (skb_headroom(skb) + toff > INT_MAX)
 				goto out;
 
 			data = skb_header_pointer(skb, toff, 4, &_data);

net/sctp/auth.c

@@ -543,16 +543,20 @@ struct sctp_hmac *sctp_auth_asoc_get_hmac(const struct sctp_association *asoc)
 		id = ntohs(hmacs->hmac_ids[i]);
 
 		/* Check the id is in the supported range */
-		if (id > SCTP_AUTH_HMAC_ID_MAX)
+		if (id > SCTP_AUTH_HMAC_ID_MAX) {
+			id = 0;
 			continue;
+		}
 
 		/* See is we support the id.  Supported IDs have name and
 		 * length fields set, so that we can allocated and use
 		 * them.  We can safely just check for name, for without the
 		 * name, we can't allocate the TFM.
 		 */
-		if (!sctp_hmac_list[id].hmac_name)
+		if (!sctp_hmac_list[id].hmac_name) {
+			id = 0;
 			continue;
+		}
 
 		break;
 	}

net/sctp/socket.c

@@ -916,6 +916,11 @@ SCTP_STATIC int sctp_setsockopt_bindx(struct sock* sk,
 	/* Walk through the addrs buffer and count the number of addresses. */
 	addr_buf = kaddrs;
 	while (walk_size < addrs_size) {
+		if (walk_size + sizeof(sa_family_t) > addrs_size) {
+			kfree(kaddrs);
+			return -EINVAL;
+		}
+
 		sa_addr = (struct sockaddr *)addr_buf;
 		af = sctp_get_af_specific(sa_addr->sa_family);
 
@@ -1002,9 +1007,13 @@ static int __sctp_connect(struct sock* sk,
 	/* Walk through the addrs buffer and count the number of addresses. */
 	addr_buf = kaddrs;
 	while (walk_size < addrs_size) {
+		if (walk_size + sizeof(sa_family_t) > addrs_size) {
+			err = -EINVAL;
+			goto out_free;
+		}
+
 		sa_addr = (union sctp_addr *)addr_buf;
 		af = sctp_get_af_specific(sa_addr->sa.sa_family);
-		port = ntohs(sa_addr->v4.sin_port);
 
 		/* If the address family is not supported or if this address
 		 * causes the address buffer to overflow return EINVAL.
@@ -1014,6 +1023,8 @@ static int __sctp_connect(struct sock* sk,
 			goto out_free;
 		}
 
+		port = ntohs(sa_addr->v4.sin_port);
+
 		/* Save current address so we can work with it */
 		memcpy(&to, sa_addr, af->sockaddr_len);