提交 80b8987c 编写于 作者: S Sergei Shtylyov 提交者: Jeff Garzik

pata_hpt{37x|3x2n}: fix clock reporting (take 2)

Fix several inconsistencies in these drivers WRT reporting the clocks:

- when using DPLL mode, 'pata_hpt37x' driver reported the DPLL frequency as the
  PCI clock -- make it properly report both clocks and add the same ability to
  the 'pata_hpt3x2n' driver;

- both drivers sometimes use "pata_hpt3*:" and sometimes "hpt3*:" in the
  messages -- make them use only the former one;

- the message about failed DPLL stablizatios deserves KERN_ERR and a bang. :-)
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
上级 d44a65f7
......@@ -24,7 +24,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt37x"
#define DRV_VERSION "0.6.8"
#define DRV_VERSION "0.6.9"
struct hpt_clock {
u8 xfer_speed;
......@@ -1112,7 +1112,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100);
}
if (adjust == 8) {
printk(KERN_WARNING "hpt37x: DPLL did not stabilize.\n");
printk(KERN_ERR "pata_hpt37x: DPLL did not stabilize!\n");
return -ENODEV;
}
if (dpll == 3)
......@@ -1120,7 +1120,8 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
else
private_data = (void *)hpt37x_timings_50;
printk(KERN_INFO "hpt37x: Bus clock %dMHz, using DPLL.\n", MHz[dpll]);
printk(KERN_INFO "pata_hpt37x: bus clock %dMHz, using %dMHz DPLL.\n",
MHz[clock_slot], MHz[dpll]);
} else {
private_data = (void *)chip_table->clocks[clock_slot];
/*
......@@ -1133,7 +1134,8 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
port = &info_hpt370_33;
if (clock_slot < 2 && port == &info_hpt370a)
port = &info_hpt370a_33;
printk(KERN_INFO "hpt37x: %s: Bus clock %dMHz.\n", chip_table->name, MHz[clock_slot]);
printk(KERN_INFO "pata_hpt37x: %s using %dMHz bus clock.\n",
chip_table->name, MHz[clock_slot]);
}
/* Now kick off ATA set up */
......
......@@ -8,7 +8,7 @@
* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
* Portions Copyright (C) 2003 Red Hat Inc
* Portions Copyright (C) 2005-2006 MontaVista Software, Inc.
* Portions Copyright (C) 2005-2007 MontaVista Software, Inc.
*
*
* TODO
......@@ -25,7 +25,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x2n"
#define DRV_VERSION "0.3.3"
#define DRV_VERSION "0.3.4"
enum {
HPT_PCI_FAST = (1 << 31),
......@@ -579,10 +579,12 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
}
if (adjust == 8) {
printk(KERN_WARNING "hpt3x2n: DPLL did not stabilize.\n");
printk(KERN_ERR "pata_hpt3x2n: DPLL did not stabilize!\n");
return -ENODEV;
}
printk(KERN_INFO "pata_hpt37x: bus clock %dMHz, using 66MHz DPLL.\n",
pci_mhz);
/* Set our private data up. We only need a few flags so we use
it directly */
port.private_data = NULL;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册