提交 7cf41601 编写于 作者: D Daniel Vetter

drm/i915: clear up backlight #define confusion on gen4+

- Regroup definitions for BLC_PWM_CTL so that they're all together and
  and ordered according to the bitfields.

- Add all missing definitions for BLC_PWM_CTL2.

- Use the BLM_ (for backlight modulation) prefix consistently.

- Note that combination mode (i.e. also taking the legacy backlight
  control value from pci config space into account) is gen4 only.

- Move the new registers for PCH-split machines up, they're an almost
  match for the gen4 defitions.  Prefix the special PCH-only bits with
  BLM_PCH_. Also add the pipe C select bit for ivb.

- Rip out the second pair of PCH polarity definitions - they're only
  valid on early (pre-production) ilk silicon.

- Adapt the existing code to use the new definitions. This has the
  nice benefit of killing a magic (1 << 30) left behind be Jesse
  Barnes.

No functional changes in this patch.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
上级 534b5a53
......@@ -1807,18 +1807,35 @@
#define PFIT_AUTO_RATIOS 0x61238
/* Backlight control */
#define BLC_PWM_CTL 0x61254
#define BACKLIGHT_MODULATION_FREQ_SHIFT (17)
#define BLC_PWM_CTL2 0x61250 /* 965+ only */
#define BLM_COMBINATION_MODE (1 << 30)
#define BLM_PWM_ENABLE (1 << 31)
#define BLM_COMBINATION_MODE (1 << 30) /* gen4 only */
#define BLM_PIPE_SELECT (1 << 29)
#define BLM_PIPE_SELECT_IVB (3 << 29)
#define BLM_PIPE_A (0 << 29)
#define BLM_PIPE_B (1 << 29)
#define BLM_PIPE_C (2 << 29) /* ivb + */
#define BLM_PIPE(pipe) ((pipe) << 29)
#define BLM_POLARITY_I965 (1 << 28) /* gen4 only */
#define BLM_PHASE_IN_INTERUPT_STATUS (1 << 26)
#define BLM_PHASE_IN_ENABLE (1 << 25)
#define BLM_PHASE_IN_INTERUPT_ENABL (1 << 24)
#define BLM_PHASE_IN_TIME_BASE_SHIFT (16)
#define BLM_PHASE_IN_TIME_BASE_MASK (0xff << 16)
#define BLM_PHASE_IN_COUNT_SHIFT (8)
#define BLM_PHASE_IN_COUNT_MASK (0xff << 8)
#define BLM_PHASE_IN_INCR_SHIFT (0)
#define BLM_PHASE_IN_INCR_MASK (0xff << 0)
#define BLC_PWM_CTL 0x61254
/*
* This is the most significant 15 bits of the number of backlight cycles in a
* complete cycle of the modulated backlight control.
*
* The actual value is this field multiplied by two.
*/
#define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17)
#define BLM_LEGACY_MODE (1 << 16)
#define BACKLIGHT_MODULATION_FREQ_SHIFT (17)
#define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17)
#define BLM_LEGACY_MODE (1 << 16) /* gen2 only */
/*
* This is the number of cycles out of the backlight modulation cycle for which
* the backlight is on.
......@@ -1833,6 +1850,19 @@
#define BLC_HIST_CTL 0x61260
/* New registers for PCH-split platforms. Safe where new bits show up, the
* register layout machtes with gen4 BLC_PWM_CTL[12]. */
#define BLC_PWM_CPU_CTL2 0x48250
#define BLC_PWM_CPU_CTL 0x48254
/* PCH CTL1 is totally different, all but the below bits are reserved. CTL2 is
* like the normal CTL from gen4 and earlier. Hooray for confusing naming. */
#define BLC_PWM_PCH_CTL1 0xc8250
#define BLM_PCH_PWM_ENABLE (1 << 30)
#define BLM_PCH_OVERRIDE_ENABLE (1 << 30)
#define BLM_PCH_POLARITY (1 << 29)
#define BLC_PWM_PCH_CTL2 0xc8254
/* TV port control */
#define TV_CTL 0x68000
/** Enables the TV encoder */
......@@ -3840,21 +3870,6 @@
#define PCH_LVDS 0xe1180
#define LVDS_DETECTED (1 << 1)
#define BLC_PWM_CPU_CTL2 0x48250
#define PWM_ENABLE (1 << 31)
#define PWM_PIPE_A (0 << 29)
#define PWM_PIPE_B (1 << 29)
#define BLC_PWM_CPU_CTL 0x48254
#define BLC_PWM_PCH_CTL1 0xc8250
#define PWM_PCH_ENABLE (1 << 31)
#define PWM_POLARITY_ACTIVE_LOW (1 << 29)
#define PWM_POLARITY_ACTIVE_HIGH (0 << 29)
#define PWM_POLARITY_ACTIVE_LOW2 (1 << 28)
#define PWM_POLARITY_ACTIVE_HIGH2 (0 << 28)
#define BLC_PWM_PCH_CTL2 0xc8254
#define PCH_PP_STATUS 0xc7200
#define PCH_PP_CONTROL 0xc7204
#define PANEL_UNLOCK_REGS (0xabcd << 16)
......
......@@ -6895,9 +6895,9 @@ static void ivb_pch_pwm_override(struct drm_device *dev)
* IVB has CPU eDP backlight regs too, set things up to let the
* PCH regs control the backlight
*/
I915_WRITE(BLC_PWM_CPU_CTL2, PWM_ENABLE);
I915_WRITE(BLC_PWM_CPU_CTL2, BLM_PWM_ENABLE);
I915_WRITE(BLC_PWM_CPU_CTL, 0);
I915_WRITE(BLC_PWM_PCH_CTL1, PWM_ENABLE | (1<<30));
I915_WRITE(BLC_PWM_PCH_CTL1, BLM_PCH_PWM_ENABLE | BLM_PCH_OVERRIDE_ENABLE);
}
void intel_modeset_init_hw(struct drm_device *dev)
......
......@@ -1081,16 +1081,16 @@ bool intel_lvds_init(struct drm_device *dev)
/* make sure PWM is enabled and locked to the LVDS pipe */
pwm = I915_READ(BLC_PWM_CPU_CTL2);
if (pipe == 0 && (pwm & PWM_PIPE_B))
I915_WRITE(BLC_PWM_CPU_CTL2, pwm & ~PWM_ENABLE);
if (pipe == 0 && (pwm & BLM_PIPE_B))
I915_WRITE(BLC_PWM_CPU_CTL2, pwm & ~BLM_PWM_ENABLE);
if (pipe)
pwm |= PWM_PIPE_B;
pwm |= BLM_PIPE_B;
else
pwm &= ~PWM_PIPE_B;
I915_WRITE(BLC_PWM_CPU_CTL2, pwm | PWM_ENABLE);
pwm &= ~BLM_PIPE_B;
I915_WRITE(BLC_PWM_CPU_CTL2, pwm | BLM_PWM_ENABLE);
pwm = I915_READ(BLC_PWM_PCH_CTL1);
pwm |= PWM_PCH_ENABLE;
pwm |= BLM_PCH_PWM_ENABLE;
I915_WRITE(BLC_PWM_PCH_CTL1, pwm);
/*
* Unlock registers and just
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册