提交 77c44ab1 编写于 作者: H Harald Welte 提交者: Linus Torvalds

[PATCH] New Omnikey Cardman 4040 driver

Add new Omnikey Cardman 4040 smartcard reader driver
Signed-off-by: NHarald Welte <laforge@gnumonks.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
上级 bca73e4b
......@@ -1873,6 +1873,11 @@ L: linux-tr@linuxtr.net
W: http://www.linuxtr.net
S: Maintained
OMNIKEY CARDMAN 4040 DRIVER
P: Harald Welte
M: laforge@gnumonks.org
S: Maintained
ONSTREAM SCSI TAPE DRIVER
P: Willem Riede
M: osst@riede.org
......
......@@ -18,5 +18,18 @@ config SYNCLINK_CS
The module will be called synclinkmp. If you want to do that, say M
here.
config CARDMAN_4040
tristate "Omnikey CardMan 4040 support"
depends on PCMCIA
help
Enable support for the Omnikey CardMan 4040 PCMCIA Smartcard
reader.
This card is basically a USB CCID device connected to a FIFO
in I/O space. To use the kernel driver, you will need either the
PC/SC ifdhandler provided from the Omnikey homepage
(http://www.omnikey.com/), or a current development version of OpenCT
(http://www.opensc.org/).
endmenu
......@@ -5,3 +5,4 @@
#
obj-$(CONFIG_SYNCLINK_CS) += synclink_cs.o
obj-$(CONFIG_CARDMAN_4040) += cm4040_cs.o
此差异已折叠。
#ifndef _CM4040_H_
#define _CM4040_H_
#define CM_MAX_DEV 4
#define DEVICE_NAME "cmx"
#define MODULE_NAME "cm4040_cs"
#define REG_OFFSET_BULK_OUT 0
#define REG_OFFSET_BULK_IN 0
#define REG_OFFSET_BUFFER_STATUS 1
#define REG_OFFSET_SYNC_CONTROL 2
#define BSR_BULK_IN_FULL 0x02
#define BSR_BULK_OUT_FULL 0x01
#define SCR_HOST_TO_READER_START 0x80
#define SCR_ABORT 0x40
#define SCR_EN_NOTIFY 0x20
#define SCR_ACK_NOTIFY 0x10
#define SCR_READER_TO_HOST_DONE 0x08
#define SCR_HOST_TO_READER_DONE 0x04
#define SCR_PULSE_INTERRUPT 0x02
#define SCR_POWER_DOWN 0x01
#define CMD_PC_TO_RDR_ICCPOWERON 0x62
#define CMD_PC_TO_RDR_GETSLOTSTATUS 0x65
#define CMD_PC_TO_RDR_ICCPOWEROFF 0x63
#define CMD_PC_TO_RDR_SECURE 0x69
#define CMD_PC_TO_RDR_GETPARAMETERS 0x6C
#define CMD_PC_TO_RDR_RESETPARAMETERS 0x6D
#define CMD_PC_TO_RDR_SETPARAMETERS 0x61
#define CMD_PC_TO_RDR_XFRBLOCK 0x6F
#define CMD_PC_TO_RDR_ESCAPE 0x6B
#define CMD_PC_TO_RDR_ICCCLOCK 0x6E
#define CMD_PC_TO_RDR_TEST_SECURE 0x74
#define CMD_PC_TO_RDR_OK_SECURE 0x89
#define CMD_RDR_TO_PC_SLOTSTATUS 0x81
#define CMD_RDR_TO_PC_DATABLOCK 0x80
#define CMD_RDR_TO_PC_PARAMETERS 0x82
#define CMD_RDR_TO_PC_ESCAPE 0x83
#define CMD_RDR_TO_PC_OK_SECURE 0x89
#endif /* _CM4040_H_ */
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册