提交 581d9baa 编写于 作者: B Ben Hutchings 提交者: David S. Miller

farsync: Fix confusion about DMA address and buffer offset types

Use dma_addr_t for DMA address parameters and u32 for shared memory
offset parameters.

Do not assume that dma_addr_t is the same as unsigned long; it will
not be in PAE configurations.  Truncate DMA addresses to 32 bits when
printing them.  This is OK because the DMA mask for this device is
32-bit (per default).

Also rename the DMA address parameters from 'skb' to 'dma'.

Compile-tested only.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 7e1a61b6
......@@ -882,20 +882,18 @@ fst_rx_dma_complete(struct fst_card_info *card, struct fst_port_info *port,
* Receive a frame through the DMA
*/
static inline void
fst_rx_dma(struct fst_card_info *card, dma_addr_t skb,
dma_addr_t mem, int len)
fst_rx_dma(struct fst_card_info *card, dma_addr_t dma, u32 mem, int len)
{
/*
* This routine will setup the DMA and start it
*/
dbg(DBG_RX, "In fst_rx_dma %lx %lx %d\n",
(unsigned long) skb, (unsigned long) mem, len);
dbg(DBG_RX, "In fst_rx_dma %x %x %d\n", (u32)dma, mem, len);
if (card->dmarx_in_progress) {
dbg(DBG_ASS, "In fst_rx_dma while dma in progress\n");
}
outl(skb, card->pci_conf + DMAPADR0); /* Copy to here */
outl(dma, card->pci_conf + DMAPADR0); /* Copy to here */
outl(mem, card->pci_conf + DMALADR0); /* from here */
outl(len, card->pci_conf + DMASIZ0); /* for this length */
outl(0x00000000c, card->pci_conf + DMADPR0); /* In this direction */
......@@ -911,20 +909,19 @@ fst_rx_dma(struct fst_card_info *card, dma_addr_t skb,
* Send a frame through the DMA
*/
static inline void
fst_tx_dma(struct fst_card_info *card, unsigned char *skb,
unsigned char *mem, int len)
fst_tx_dma(struct fst_card_info *card, dma_addr_t dma, u32 mem, int len)
{
/*
* This routine will setup the DMA and start it.
*/
dbg(DBG_TX, "In fst_tx_dma %p %p %d\n", skb, mem, len);
dbg(DBG_TX, "In fst_tx_dma %x %x %d\n", (u32)dma, mem, len);
if (card->dmatx_in_progress) {
dbg(DBG_ASS, "In fst_tx_dma while dma in progress\n");
}
outl((unsigned long) skb, card->pci_conf + DMAPADR1); /* Copy from here */
outl((unsigned long) mem, card->pci_conf + DMALADR1); /* to here */
outl(dma, card->pci_conf + DMAPADR1); /* Copy from here */
outl(mem, card->pci_conf + DMALADR1); /* to here */
outl(len, card->pci_conf + DMASIZ1); /* for this length */
outl(0x000000004, card->pci_conf + DMADPR1); /* In this direction */
......@@ -1401,9 +1398,7 @@ do_bottom_half_tx(struct fst_card_info *card)
card->dma_len_tx = skb->len;
card->dma_txpos = port->txpos;
fst_tx_dma(card,
(char *) card->
tx_dma_handle_card,
(char *)
card->tx_dma_handle_card,
BUF_OFFSET(txBuffer[pi]
[port->txpos][0]),
skb->len);
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册