提交 556cc1c5 编写于 作者: A Alexey Brodkin 提交者: Vineet Gupta

ARC: [axs101] Add support for AXS101 SDP (software development platform)

The AXS10x platforms consist of a mainboard with peripherals,
on which several daughter cards can be placed. The daughter cards
typically contain a CPU and memory.
Signed-off-by: NMischa Jonker <mjonker@synopsys.com>
Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>
上级 4db27dca
Synopsys DesignWare ARC Software Development Platforms Device Tree Bindings
---------------------------------------------------------------------------
SDP Main Board with an AXC001 CPU Card hoisting ARC700 core in silicon
Required root node properties:
- compatible = "snps,axs101";
......@@ -9579,6 +9579,13 @@ F: arch/arc/
F: Documentation/devicetree/bindings/arc/
F: drivers/tty/serial/arc_uart.c
SYNOPSYS ARC SDP platform support
M: Alexey Brodkin <abrodkin@synopsys.com>
S: Supported
F: arch/arc/plat-axs10x
F: arch/arc/boot/dts/ax*
F: Documentation/devicetree/bindings/arc/axs10*
SYSV FILESYSTEM
M: Christoph Hellwig <hch@infradead.org>
S: Maintained
......
......@@ -83,6 +83,7 @@ menu "ARC Platform/SoC/Board"
source "arch/arc/plat-sim/Kconfig"
source "arch/arc/plat-tb10x/Kconfig"
source "arch/arc/plat-axs10x/Kconfig"
#New platform adds here
endmenu
......
......@@ -83,6 +83,7 @@ core-y += arch/arc/boot/dts/
core-$(CONFIG_ARC_PLAT_SIM) += arch/arc/plat-sim/
core-$(CONFIG_ARC_PLAT_TB10X) += arch/arc/plat-tb10x/
core-$(CONFIG_ARC_PLAT_AXS10X) += arch/arc/plat-axs10x/
drivers-$(CONFIG_OPROFILE) += arch/arc/oprofile/
......
/*
* Copyright (C) 2013-15 Synopsys, Inc. (www.synopsys.com)
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/*
* Device tree for AXC001 770D/EM6/AS221 CPU card
* Note that this file only supports the 770D CPU
*/
/ {
compatible = "snps,arc";
clock-frequency = <750000000>; /* 750 MHZ */
#address-cells = <1>;
#size-cells = <1>;
cpu_card {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x00000000 0xf0000000 0x10000000>;
cpu_intc: arc700-intc@cpu {
compatible = "snps,arc700-intc";
interrupt-controller;
#interrupt-cells = <1>;
};
/*
* this GPIO block ORs all interrupts on CPU card (creg,..)
* to uplink only 1 IRQ to ARC core intc
*/
dw-apb-gpio@0x2000 {
compatible = "snps,dw-apb-gpio";
reg = < 0x2000 0x80 >;
#address-cells = <1>;
#size-cells = <0>;
ictl_intc: gpio-controller@0 {
compatible = "snps,dw-apb-gpio-port";
gpio-controller;
#gpio-cells = <2>;
snps,nr-gpios = <30>;
reg = <0>;
interrupt-controller;
#interrupt-cells = <2>;
interrupt-parent = <&cpu_intc>;
interrupts = <15>;
};
};
debug_uart: dw-apb-uart@0x5000 {
compatible = "snps,dw-apb-uart";
reg = <0x5000 0x100>;
clock-frequency = <33333000>;
interrupt-parent = <&ictl_intc>;
interrupts = <19 4>;
baud = <115200>;
reg-shift = <2>;
reg-io-width = <4>;
};
arcpmu0: pmu {
compatible = "snps,arc700-pct";
};
};
memory {
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x00000000 0x80000000 0x40000000>;
device_type = "memory";
reg = <0x00000000 0x20000000>; /* 512MiB */
};
};
/*
* Copyright (C) 2013-15 Synopsys, Inc. (www.synopsys.com)
*
* ARC AXS101 S/W development platform
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/dts-v1/;
/include/ "axc001.dtsi"
/include/ "axs10x_mb.dtsi"
/ {
compatible = "snps,axs101";
chosen {
bootargs = "console=tty0 console=ttyS3,115200n8 consoleblank=0";
};
};
/*
* Support for peripherals on the AXS10x mainboard
*
* Copyright (C) 2013-15 Synopsys, Inc. (www.synopsys.com)
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/ {
axs10x_mb {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x00000000 0xe0000000 0x10000000>;
interrupt-parent = <&mb_intc>;
clocks {
i2cclk: i2cclk {
compatible = "fixed-clock";
clock-frequency = <50000000>;
#clock-cells = <0>;
};
apbclk: apbclk {
compatible = "fixed-clock";
clock-frequency = <50000000>;
#clock-cells = <0>;
};
mmcclk: mmcclk {
compatible = "fixed-clock";
clock-frequency = <50000000>;
#clock-cells = <0>;
};
};
/*
* This INTC is actually connected to DW APB GPIO
* which acts as a wire between MB INTC and CPU INTC.
* GPIO INTC is configured in platform init code
* and here we mimic direct connection from MB INTC to
* CPU INTC, thus we set "interrupts = <7>" instead of
* "interrupts = <12>"
*/
mb_intc: dw-apb-ictl@0x12000 {
#interrupt-cells = <1>;
compatible = "snps,dw-apb-ictl";
reg = < 0x12000 0x200 >;
interrupt-controller;
interrupt-parent = <&cpu_intc>;
interrupts = < 7 >;
};
ethernet@0x18000 {
#interrupt-cells = <1>;
compatible = "snps,dwmac";
reg = < 0x18000 0x2000 >;
interrupts = < 4 >;
interrupt-names = "macirq";
phy-mode = "rgmii";
snps,pbl = < 32 >;
clocks = <&apbclk>;
clock-names = "stmmaceth";
};
ehci@0x40000 {
compatible = "generic-ehci";
reg = < 0x40000 0x100 >;
interrupts = < 8 >;
};
ohci@0x60000 {
compatible = "generic-ohci";
reg = < 0x60000 0x100 >;
interrupts = < 8 >;
};
mmc@0x15000 {
compatible = "snps,dw-mshc";
reg = < 0x15000 0x400 >;
num-slots = < 1 >;
fifo-depth = < 16 >;
card-detect-delay = < 200 >;
clocks = <&apbclk>, <&mmcclk>;
clock-names = "biu", "ciu";
interrupts = < 7 >;
bus-width = < 4 >;
};
uart@0x20000 {
compatible = "snps,dw-apb-uart";
reg = <0x20000 0x100>;
clock-frequency = <33333333>;
interrupts = <17>;
baud = <115200>;
reg-shift = <2>;
reg-io-width = <4>;
};
uart@0x21000 {
compatible = "snps,dw-apb-uart";
reg = <0x21000 0x100>;
clock-frequency = <33333333>;
interrupts = <18>;
baud = <115200>;
reg-shift = <2>;
reg-io-width = <4>;
};
/* UART muxed with USB data port (ttyS3) */
uart@0x22000 {
compatible = "snps,dw-apb-uart";
reg = <0x22000 0x100>;
clock-frequency = <33333333>;
interrupts = <19>;
baud = <115200>;
reg-shift = <2>;
reg-io-width = <4>;
};
i2c@0x1d000 {
compatible = "snps,designware-i2c";
reg = <0x1d000 0x100>;
clock-frequency = <400000>;
clocks = <&i2cclk>;
interrupts = <14>;
};
i2c@0x1e000 {
compatible = "snps,designware-i2c";
reg = <0x1e000 0x100>;
clock-frequency = <400000>;
clocks = <&i2cclk>;
interrupts = <15>;
};
i2c@0x1f000 {
compatible = "snps,designware-i2c";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x1f000 0x100>;
clock-frequency = <400000>;
clocks = <&i2cclk>;
interrupts = <16>;
eeprom@0x54{
compatible = "24c01";
reg = <0x54>;
pagesize = <0x8>;
};
eeprom@0x57{
compatible = "24c04";
reg = <0x57>;
pagesize = <0x8>;
};
};
gpio0:gpio@13000 {
compatible = "snps,dw-apb-gpio";
reg = <0x13000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
gpio0_banka: gpio-controller@0 {
compatible = "snps,dw-apb-gpio-port";
gpio-controller;
#gpio-cells = <2>;
snps,nr-gpios = <32>;
reg = <0>;
};
gpio0_bankb: gpio-controller@1 {
compatible = "snps,dw-apb-gpio-port";
gpio-controller;
#gpio-cells = <2>;
snps,nr-gpios = <8>;
reg = <1>;
};
gpio0_bankc: gpio-controller@2 {
compatible = "snps,dw-apb-gpio-port";
gpio-controller;
#gpio-cells = <2>;
snps,nr-gpios = <8>;
reg = <2>;
};
};
gpio1:gpio@14000 {
compatible = "snps,dw-apb-gpio";
reg = <0x14000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
gpio1_banka: gpio-controller@0 {
compatible = "snps,dw-apb-gpio-port";
gpio-controller;
#gpio-cells = <2>;
snps,nr-gpios = <30>;
reg = <0>;
};
gpio1_bankb: gpio-controller@1 {
compatible = "snps,dw-apb-gpio-port";
gpio-controller;
#gpio-cells = <2>;
snps,nr-gpios = <10>;
reg = <1>;
};
gpio1_bankc: gpio-controller@2 {
compatible = "snps,dw-apb-gpio-port";
gpio-controller;
#gpio-cells = <2>;
snps,nr-gpios = <8>;
reg = <2>;
};
};
};
};
CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
CONFIG_DEFAULT_HOSTNAME="ARCLinux"
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_CROSS_MEMORY_ATTACH is not set
CONFIG_NO_HZ_IDLE=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_NAMESPACES=y
# CONFIG_UTS_NS is not set
# CONFIG_PID_NS is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE="../arc_initramfs/"
CONFIG_EMBEDDED=y
CONFIG_PERF_EVENTS=y
# CONFIG_VM_EVENT_COUNTERS is not set
# CONFIG_SLUB_DEBUG is not set
# CONFIG_COMPAT_BRK is not set
CONFIG_MODULES=y
CONFIG_PARTITION_ADVANCED=y
CONFIG_ARC_PLAT_AXS10X=y
CONFIG_AXS101=y
CONFIG_ARC_CACHE_LINE_SHIFT=5
CONFIG_ARC_BUILTIN_DTB_NAME="axs101"
CONFIG_PREEMPT=y
# CONFIG_COMPACTION is not set
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_NET_KEY=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
# CONFIG_IPV6 is not set
# CONFIG_STANDALONE is not set
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
# CONFIG_FIRMWARE_IN_KERNEL is not set
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_NETDEVICES=y
# CONFIG_NET_VENDOR_ARC is not set
# CONFIG_NET_VENDOR_BROADCOM is not set
# CONFIG_NET_VENDOR_INTEL is not set
# CONFIG_NET_VENDOR_MARVELL is not set
# CONFIG_NET_VENDOR_MICREL is not set
# CONFIG_NET_VENDOR_NATSEMI is not set
# CONFIG_NET_VENDOR_SEEQ is not set
CONFIG_STMMAC_ETH=y
# CONFIG_NET_VENDOR_VIA is not set
# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_NATIONAL_PHY=y
# CONFIG_USB_NET_DRIVERS is not set
CONFIG_INPUT_EVDEV=y
CONFIG_MOUSE_PS2_TOUCHKIT=y
CONFIG_MOUSE_SERIAL=y
CONFIG_MOUSE_SYNAPTICS_USB=y
# CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVKMEM is not set
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_DW=y
CONFIG_SERIAL_OF_PLATFORM=y
# CONFIG_HW_RANDOM is not set
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_DESIGNWARE_PLATFORM=y
# CONFIG_HWMON is not set
CONFIG_FB=y
# CONFIG_VGA_CONSOLE is not set
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
# CONFIG_LOGO_LINUX_CLUT224 is not set
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_HCD_PLATFORM=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_OHCI_HCD_PLATFORM=y
CONFIG_USB_STORAGE=y
CONFIG_MMC=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_PLTFM=y
CONFIG_MMC_DW=y
CONFIG_MMC_DW_IDMAC=y
# CONFIG_IOMMU_SUPPORT is not set
CONFIG_EXT3_FS=y
CONFIG_EXT4_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_NTFS_FS=y
CONFIG_TMPFS=y
CONFIG_JFFS2_FS=y
CONFIG_NFS_FS=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
# CONFIG_ENABLE_WARN_DEPRECATED is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_STRIP_ASM_SYMS=y
CONFIG_LOCKUP_DETECTOR=y
CONFIG_DEFAULT_HUNG_TASK_TIMEOUT=10
# CONFIG_SCHED_DEBUG is not set
# CONFIG_DEBUG_PREEMPT is not set
# CONFIG_FTRACE is not set
#
# Copyright (C) 2013-15 Synopsys, Inc. (www.synopsys.com)
#
# This program is free software; you can redistribute it and/or modify
# it under the terms of the GNU General Public License version 2 as
# published by the Free Software Foundation.
#
config ARC_PLAT_AXS10X
bool "Synopsys ARC AXS10x Software Development Platforms"
select DW_APB_ICTL
select GPIO_DWAPB
select OF_GPIO
select GENERIC_IRQ_CHIP
select ARCH_REQUIRE_GPIOLIB
help
Support for the ARC AXS10x Software Development Platforms.
The AXS10x Platforms consist of a mainboard with peripherals,
on which several daughter cards can be placed. The daughter cards
typically contain a CPU and memory.
if ARC_PLAT_AXS10X
config AXS101
bool "AXS101 with AXC001 CPU Card (ARC 770D/EM6/AS221)"
help
This adds support for the 770D/EM6/AS221 CPU Card. Only the ARC
770D is supported in Linux.
The AXS101 Platform consists of an AXS10x mainboard with
this daughtercard. Please use the axs101.dts device tree
with this configuration.
endif
#
# Copyright (C) 2013-15 Synopsys, Inc. (www.synopsys.com)
#
# This program is free software; you can redistribute it and/or modify
# it under the terms of the GNU General Public License version 2 as
# published by the Free Software Foundation.
#
obj-$(CONFIG_ARC_PLAT_AXS10X) += axs10x.o
/*
* AXS101 Software Development Platform
*
* Copyright (C) 2013-15 Synopsys, Inc. (www.synopsys.com)
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
*/
#include <linux/of_platform.h>
#include <asm/mach_desc.h>
#include <asm/io.h>
#define AXS_MB_CGU 0xE0010000
#define AXS_MB_CREG 0xE0011000
#define CREG_MB_IRQ_MUX (AXS_MB_CREG + 0x214)
#define CREG_MB_SW_RESET (AXS_MB_CREG + 0x220)
#define CREG_MB_VER (AXS_MB_CREG + 0x230)
#define CREG_MB_CONFIG (AXS_MB_CREG + 0x234)
#define AXC001_CREG 0xF0001000
#define AXC001_GPIO_INTC 0xF0003000
#define CREG_CPU_ADDR_770 (AXC001_CREG + 0x20)
#define CREG_CPU_ADDR_TUNN (AXC001_CREG + 0x60)
#define CREG_CPU_ADDR_770_UPD (AXC001_CREG + 0x34)
#define CREG_CPU_ADDR_TUNN_UPD (AXC001_CREG + 0x74)
#define CREG_CPU_ARC770_IRQ_MUX (AXC001_CREG + 0x114)
#define CREG_CPU_GPIO_UART_MUX (AXC001_CREG + 0x120)
static void enable_gpio_intc_wire(void)
{
/*
* Peripherals on CPU Card and Mother Board are wired to cpu intc via
* intermediate DW APB GPIO blocks (mainly for debouncing)
*
* ---------------------
* | snps,arc700-intc |
* ---------------------
* | #7 | #15
* ------------------- -------------------
* | snps,dw-apb-gpio | | snps,dw-apb-gpio |
* ------------------- -------------------
* | |
* | [ Debug UART on cpu card ]
* |
* ------------------------
* | snps,dw-apb-intc (MB)|
* ------------------------
* | | | |
* [eth] [uart] [... other perip on Main Board]
*
* Current implementation of "irq-dw-apb-ictl" driver doesn't work well
* with stacked INTCs. In particular problem happens if its master INTC
* not yet instantiated. See discussion here -
* https://lkml.org/lkml/2015/3/4/755
*
* So setup the first gpio block as a passive pass thru and hide it from
* DT hardware topology - connect MB intc directly to cpu intc
* The GPIO "wire" needs to be init nevertheless (here)
*
* One side adv is that peripheral interrupt handling avoids one nested
* intc ISR hop
*/
#define GPIO_INTEN (AXC001_GPIO_INTC + 0x30)
#define GPIO_INTMASK (AXC001_GPIO_INTC + 0x34)
#define GPIO_INTTYPE_LEVEL (AXC001_GPIO_INTC + 0x38)
#define GPIO_INT_POLARITY (AXC001_GPIO_INTC + 0x3c)
#define MB_TO_GPIO_IRQ 12
iowrite32(~(1 << MB_TO_GPIO_IRQ), (void __iomem *) GPIO_INTMASK);
iowrite32(0, (void __iomem *) GPIO_INTTYPE_LEVEL);
iowrite32(~0, (void __iomem *) GPIO_INT_POLARITY);
iowrite32(1 << MB_TO_GPIO_IRQ, (void __iomem *) GPIO_INTEN);
}
static void axs10x_print_board_ver(unsigned int creg, const char *str)
{
union ver {
struct {
#ifdef CONFIG_CPU_BIG_ENDIAN
unsigned int pad:11, y:12, m:4, d:5;
#else
unsigned int d:5, m:4, y:12, pad:11;
#endif
};
unsigned int val;
} board;
board.val = ioread32((void __iomem *)creg);
pr_info("AXS: %s FPGA Date: %u-%u-%u\n", str, board.d, board.m,
board.y);
}
static void axs10x_early_init(void)
{
int mb_rev;
char mb[32];
/* Determine motherboard version */
if (ioread32((void __iomem *) CREG_MB_CONFIG) & (1 << 28))
mb_rev = 3; /* HT-3 (rev3.0) */
else
mb_rev = 2; /* HT-2 (rev2.0) */
enable_gpio_intc_wire();
scnprintf(mb, 32, "MainBoard v%d", mb_rev);
axs10x_print_board_ver(CREG_MB_VER, mb);
}
/*
* Set up System Memory Map for ARC cpu / peripherals controllers
*
* Each AXI master has a 4GB memory map specified as 16 apertures of 256MB, each
* of which maps to a corresponding 256MB aperture in Target slave memory map.
*
* e.g. ARC cpu AXI Master's aperture 8 (0x8000_0000) is mapped to aperture 0
* (0x0000_0000) of DDR Port 0 (slave #1)
*
* Access from cpu to MB controllers such as GMAC is setup using AXI Tunnel:
* which has master/slaves on both ends.
* e.g. aperture 14 (0xE000_0000) of ARC cpu is mapped to aperture 14
* (0xE000_0000) of CPU Card AXI Tunnel slave (slave #3) which is mapped to
* MB AXI Tunnel Master, which also has a mem map setup
*
* In the reverse direction, MB AXI Masters (e.g. GMAC) mem map is setup
* to map to MB AXI Tunnel slave which connects to CPU Card AXI Tunnel Master
*/
struct aperture {
unsigned int slave_sel:4, slave_off:4, pad:24;
};
/* CPU Card target slaves */
#define AXC001_SLV_NONE 0
#define AXC001_SLV_DDR_PORT0 1
#define AXC001_SLV_SRAM 2
#define AXC001_SLV_AXI_TUNNEL 3
#define AXC001_SLV_AXI2APB 6
#define AXC001_SLV_DDR_PORT1 7
/* MB AXI Target slaves */
#define AXS_MB_SLV_NONE 0
#define AXS_MB_SLV_AXI_TUNNEL_CPU 1
#define AXS_MB_SLV_AXI_TUNNEL_HAPS 2
#define AXS_MB_SLV_SRAM 3
#define AXS_MB_SLV_CONTROL 4
/* MB AXI masters */
#define AXS_MB_MST_TUNNEL_CPU 0
#define AXS_MB_MST_USB_OHCI 10
/*
* memmap for ARC core on CPU Card
*/
static const struct aperture axc001_memmap[16] = {
{AXC001_SLV_AXI_TUNNEL, 0x0},
{AXC001_SLV_AXI_TUNNEL, 0x1},
{AXC001_SLV_SRAM, 0x0}, /* 0x2000_0000: Local SRAM */
{AXC001_SLV_NONE, 0x0},
{AXC001_SLV_NONE, 0x0},
{AXC001_SLV_NONE, 0x0},
{AXC001_SLV_NONE, 0x0},
{AXC001_SLV_NONE, 0x0},
{AXC001_SLV_DDR_PORT0, 0x0}, /* 0x8000_0000: DDR 0..256M */
{AXC001_SLV_DDR_PORT0, 0x1}, /* 0x9000_0000: DDR 256..512M */
{AXC001_SLV_DDR_PORT1, 0x0},
{AXC001_SLV_DDR_PORT1, 0x1},
{AXC001_SLV_NONE, 0x0},
{AXC001_SLV_AXI_TUNNEL, 0xD},
{AXC001_SLV_AXI_TUNNEL, 0xE}, /* MB: CREG, CGU... */
{AXC001_SLV_AXI2APB, 0x0}, /* CPU Card local CREG, CGU... */
};
/*
* memmap for CPU Card AXI Tunnel Master (for access by MB controllers)
* GMAC (MB) -> MB AXI Tunnel slave -> CPU Card AXI Tunnel Master -> DDR
*/
static const struct aperture axc001_axi_tunnel_memmap[16] = {
{AXC001_SLV_AXI_TUNNEL, 0x0},
{AXC001_SLV_AXI_TUNNEL, 0x1},
{AXC001_SLV_SRAM, 0x0},
{AXC001_SLV_NONE, 0x0},
{AXC001_SLV_NONE, 0x0},
{AXC001_SLV_NONE, 0x0},
{AXC001_SLV_NONE, 0x0},
{AXC001_SLV_NONE, 0x0},
{AXC001_SLV_DDR_PORT0, 0x0},
{AXC001_SLV_DDR_PORT0, 0x1},
{AXC001_SLV_DDR_PORT1, 0x0},
{AXC001_SLV_DDR_PORT1, 0x1},
{AXC001_SLV_NONE, 0x0},
{AXC001_SLV_AXI_TUNNEL, 0xD},
{AXC001_SLV_AXI_TUNNEL, 0xE},
{AXC001_SLV_AXI2APB, 0x0},
};
/*
* memmap for MB AXI Masters
* Same mem map for all perip controllers as well as MB AXI Tunnel Master
*/
static const struct aperture axs_mb_memmap[16] = {
{AXS_MB_SLV_SRAM, 0x0},
{AXS_MB_SLV_SRAM, 0x0},
{AXS_MB_SLV_NONE, 0x0},
{AXS_MB_SLV_NONE, 0x0},
{AXS_MB_SLV_NONE, 0x0},
{AXS_MB_SLV_NONE, 0x0},
{AXS_MB_SLV_NONE, 0x0},
{AXS_MB_SLV_NONE, 0x0},
{AXS_MB_SLV_AXI_TUNNEL_CPU, 0x8}, /* DDR on CPU Card */
{AXS_MB_SLV_AXI_TUNNEL_CPU, 0x9}, /* DDR on CPU Card */
{AXS_MB_SLV_AXI_TUNNEL_CPU, 0xA},
{AXS_MB_SLV_AXI_TUNNEL_CPU, 0xB},
{AXS_MB_SLV_NONE, 0x0},
{AXS_MB_SLV_AXI_TUNNEL_HAPS, 0xD},
{AXS_MB_SLV_CONTROL, 0x0}, /* MB Local CREG, CGU... */
{AXS_MB_SLV_AXI_TUNNEL_CPU, 0xF},
};
static noinline void
axs101_set_memmap(void __iomem *base, const struct aperture map[16])
{
unsigned int slave_select, slave_offset;
int i;
slave_select = slave_offset = 0;
for (i = 0; i < 8; i++) {
slave_select |= map[i].slave_sel << (i << 2);
slave_offset |= map[i].slave_off << (i << 2);
}
iowrite32(slave_select, base + 0x0); /* SLV0 */
iowrite32(slave_offset, base + 0x8); /* OFFSET0 */
slave_select = slave_offset = 0;
for (i = 0; i < 8; i++) {
slave_select |= map[i+8].slave_sel << (i << 2);
slave_offset |= map[i+8].slave_off << (i << 2);
}
iowrite32(slave_select, base + 0x4); /* SLV1 */
iowrite32(slave_offset, base + 0xC); /* OFFSET1 */
}
static void axs101_early_init(void)
{
int i;
/* ARC 770D memory view */
axs101_set_memmap((void __iomem *) CREG_CPU_ADDR_770, axc001_memmap);
iowrite32(1, (void __iomem *) CREG_CPU_ADDR_770_UPD);
/* AXI tunnel memory map (incoming traffic from MB into CPU Card */
axs101_set_memmap((void __iomem *) CREG_CPU_ADDR_TUNN,
axc001_axi_tunnel_memmap);
iowrite32(1, (void __iomem *) CREG_CPU_ADDR_TUNN_UPD);
/* MB peripherals memory map */
for (i = AXS_MB_MST_TUNNEL_CPU; i <= AXS_MB_MST_USB_OHCI; i++)
axs101_set_memmap((void __iomem *) AXS_MB_CREG + (i << 4),
axs_mb_memmap);
iowrite32(0x3ff, (void __iomem *) AXS_MB_CREG + 0x100); /* Update */
/* GPIO pins 18 and 19 are used as UART rx and tx, respectively. */
iowrite32(0x01, (void __iomem *) CREG_CPU_GPIO_UART_MUX);
/* Set up the MB interrupt system: mux interrupts to GPIO7) */
iowrite32(0x01, (void __iomem *) CREG_MB_IRQ_MUX);
/* reset ethernet and ULPI interfaces */
iowrite32(0x18, (void __iomem *) CREG_MB_SW_RESET);
/* map GPIO 14:10 to ARC 9:5 (IRQ mux change for MB v2 onwards) */
iowrite32(0x52, (void __iomem *) CREG_CPU_ARC770_IRQ_MUX);
axs10x_early_init();
}
static const char *axs101_compat[] __initconst = {
"snps,axs101",
NULL,
};
MACHINE_START(AXS101, "axs101")
.dt_compat = axs101_compat,
.init_early = axs101_early_init,
MACHINE_END
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册