[libata] mark certain hardware (or drivers) with a no-atapi flag

Some hardware does not support the PACKET command at all.
Other hardware supports ATAPI, but the driver does something nasty such
as calling BUG() when an ATAPI command is issued.

For these such cases, we mark them with a new flag, ATA_FLAG_NO_ATAPI.

Initial version contributed by Ben Collins.

drivers/scsi/libata-scsi.c

@@ -2173,9 +2173,12 @@ ata_scsi_find_dev(struct ata_port *ap, const struct scsi_device *scsidev)
 	if (unlikely(!ata_dev_present(dev)))
 		return NULL;
 
-	if (!atapi_enabled) {
-		if (unlikely(dev->class == ATA_DEV_ATAPI))
+	if (!atapi_enabled || (ap->flags & ATA_FLAG_NO_ATAPI)) {
+		if (unlikely(dev->class == ATA_DEV_ATAPI)) {
+			printk(KERN_WARNING "ata%u(%u): WARNING: ATAPI is %s, device ignored.\n",
+			       ap->id, dev->devno, atapi_enabled ? "not supported with this driver" : "disabled");
 			return NULL;
+		}
 	}
 
 	return dev;

drivers/scsi/sata_mv.c

@@ -86,7 +86,8 @@ enum {
 	MV_FLAG_DUAL_HC		= (1 << 30),  /* two SATA Host Controllers */
 	MV_FLAG_IRQ_COALESCE	= (1 << 29),  /* IRQ coalescing capability */
 	MV_COMMON_FLAGS		= (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
-				   ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO),
+				   ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO |
+				   ATA_FLAG_NO_ATAPI),
 	MV_6XXX_FLAGS		= MV_FLAG_IRQ_COALESCE,
 
 	CRQB_FLAG_READ		= (1 << 0),

drivers/scsi/sata_promise.c

@@ -70,6 +70,9 @@ enum {
 	PDC_HAS_PATA		= (1 << 1), /* PDC20375 has PATA */
 
 	PDC_RESET		= (1 << 11), /* HDMA reset */
+
+	PDC_COMMON_FLAGS	= ATA_FLAG_NO_LEGACY | ATA_FLAG_SRST |
+				  ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI,
 };
 
 
@@ -162,8 +165,7 @@ static struct ata_port_info pdc_port_info[] = {
 	/* board_2037x */
 	{
 		.sht		= &pdc_ata_sht,
-		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
-				  ATA_FLAG_SRST | ATA_FLAG_MMIO,
+		.host_flags	= PDC_COMMON_FLAGS | ATA_FLAG_SATA,
 		.pio_mask	= 0x1f, /* pio0-4 */
 		.mwdma_mask	= 0x07, /* mwdma0-2 */
 		.udma_mask	= 0x7f, /* udma0-6 ; FIXME */
@@ -173,8 +175,7 @@ static struct ata_port_info pdc_port_info[] = {
 	/* board_20319 */
 	{
 		.sht		= &pdc_ata_sht,
-		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
-				  ATA_FLAG_SRST | ATA_FLAG_MMIO,
+		.host_flags	= PDC_COMMON_FLAGS | ATA_FLAG_SATA,
 		.pio_mask	= 0x1f, /* pio0-4 */
 		.mwdma_mask	= 0x07, /* mwdma0-2 */
 		.udma_mask	= 0x7f, /* udma0-6 ; FIXME */
@@ -184,8 +185,7 @@ static struct ata_port_info pdc_port_info[] = {
 	/* board_20619 */
 	{
 		.sht		= &pdc_ata_sht,
-		.host_flags	= ATA_FLAG_NO_LEGACY | ATA_FLAG_SRST |
-				  ATA_FLAG_MMIO | ATA_FLAG_SLAVE_POSS,
+		.host_flags	= PDC_COMMON_FLAGS | ATA_FLAG_SLAVE_POSS,
 		.pio_mask	= 0x1f, /* pio0-4 */
 		.mwdma_mask	= 0x07, /* mwdma0-2 */
 		.udma_mask	= 0x7f, /* udma0-6 ; FIXME */

drivers/scsi/sata_sx4.c

@@ -220,7 +220,8 @@ static struct ata_port_info pdc_port_info[] = {
 	{
 		.sht		= &pdc_sata_sht,
 		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
-				  ATA_FLAG_SRST | ATA_FLAG_MMIO,
+				  ATA_FLAG_SRST | ATA_FLAG_MMIO |
+				  ATA_FLAG_NO_ATAPI,
 		.pio_mask	= 0x1f, /* pio0-4 */
 		.mwdma_mask	= 0x07, /* mwdma0-2 */
 		.udma_mask	= 0x7f, /* udma0-6 ; FIXME */

include/linux/libata.h

@@ -122,6 +122,7 @@ enum {
 	ATA_FLAG_NOINTR		= (1 << 9), /* FIXME: Remove this once
 					     * proper HSM is in place. */
 	ATA_FLAG_DEBUGMSG	= (1 << 10),
+	ATA_FLAG_NO_ATAPI	= (1 << 11), /* No ATAPI support */
 
 	ATA_QCFLAG_ACTIVE	= (1 << 1), /* cmd not yet ack'd to scsi lyer */
 	ATA_QCFLAG_SG		= (1 << 3), /* have s/g table? */