提交 3f518509 编写于 作者: M Marcin Wojtas 提交者: David S. Miller

ethernet: Add new driver for Marvell Armada 375 network unit

This commit adds a new network driver for the network controller in Marvell
Armada 375 SoC.

Given the controller is very different from the ones in the other Marvell
SoCs that use the mv643xx_eth (Kirkwood, Orion, Discovery) and mvneta
(Armada 370/38x/XP) drivers, a new driver is needed.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
[Ezequiel: coding style cleanup]
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 b6428817
* Marvell Armada 375 Ethernet Controller (PPv2)
Required properties:
- compatible: should be "marvell,armada-375-pp2"
- reg: addresses and length of the register sets for the device.
Must contain the following register sets:
- common controller registers
- LMS registers
In addition, at least one port register set is required.
- clocks: a pointer to the reference clocks for this device, consequently:
- main controller clock
- GOP clock
- clock-names: names of used clocks, must be "pp_clk" and "gop_clk".
The ethernet ports are represented by subnodes. At least one port is
required.
Required properties (port):
- interrupts: interrupt for the port
- port-id: should be '0' or '1' for ethernet ports, and '2' for the
loopback port
- phy-mode: See ethernet.txt file in the same directory
Optional properties (port):
- marvell,loopback: port is loopback mode
- phy: a phandle to a phy node defining the PHY address (as the reg
property, a single integer). Note: if this property isn't present,
then fixed link is assumed, and the 'fixed-link' property is
mandatory.
Example:
ethernet@f0000 {
compatible = "marvell,armada-375-pp2";
reg = <0xf0000 0xa000>,
<0xc0000 0x3060>,
<0xc4000 0x100>,
<0xc5000 0x100>;
clocks = <&gateclk 3>, <&gateclk 19>;
clock-names = "pp_clk", "gop_clk";
status = "okay";
eth0: eth0@c4000 {
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
port-id = <0>;
status = "okay";
phy = <&phy0>;
phy-mode = "gmii";
};
eth1: eth1@c5000 {
interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
port-id = <1>;
status = "okay";
phy = <&phy3>;
phy-mode = "gmii";
};
};
...@@ -54,6 +54,14 @@ config MVNETA ...@@ -54,6 +54,14 @@ config MVNETA
driver, which should be used for the older Marvell SoCs driver, which should be used for the older Marvell SoCs
(Dove, Orion, Discovery, Kirkwood). (Dove, Orion, Discovery, Kirkwood).
config MVPP2
tristate "Marvell Armada 375 network interface support"
depends on MACH_ARMADA_375
select MVMDIO
---help---
This driver supports the network interface units in the
Marvell ARMADA 375 SoC.
config PXA168_ETH config PXA168_ETH
tristate "Marvell pxa168 ethernet support" tristate "Marvell pxa168 ethernet support"
depends on CPU_PXA168 depends on CPU_PXA168
......
...@@ -5,6 +5,7 @@ ...@@ -5,6 +5,7 @@
obj-$(CONFIG_MVMDIO) += mvmdio.o obj-$(CONFIG_MVMDIO) += mvmdio.o
obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o
obj-$(CONFIG_MVNETA) += mvneta.o obj-$(CONFIG_MVNETA) += mvneta.o
obj-$(CONFIG_MVPP2) += mvpp2.o
obj-$(CONFIG_PXA168_ETH) += pxa168_eth.o obj-$(CONFIG_PXA168_ETH) += pxa168_eth.o
obj-$(CONFIG_SKGE) += skge.o obj-$(CONFIG_SKGE) += skge.o
obj-$(CONFIG_SKY2) += sky2.o obj-$(CONFIG_SKY2) += sky2.o
此差异已折叠。
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册