drm/i915: Workaround to bump rc6 voltage to 450

BIOS should be setting the minimum voltage for rc6 to be 450mV. Old or
buggy BIOSen may not be doing this, so we correct it for them. Ideally
customers should update the BIOS as only it would know the optimal
values for the platform, so we leave that fact as a DRM_ERROR for the
user to see.

Unfortunately this isn't fixing any of the issues it was targeted to
fix, but it is documented that we must do it.

CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Matt Turner <mattst88@gmail.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: bikeshedded loglevel of the "your bios is broken message" to
debug.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

drivers/gpu/drm/i915/i915_reg.h

@@ -4225,6 +4225,10 @@
 #define   GEN6_READ_OC_PARAMS			0xc
 #define   GEN6_PCODE_WRITE_MIN_FREQ_TABLE	0x8
 #define   GEN6_PCODE_READ_MIN_FREQ_TABLE	0x9
+#define	  GEN6_PCODE_WRITE_RC6VIDS		0x4
+#define	  GEN6_PCODE_READ_RC6VIDS		0x5
+#define   GEN6_ENCODE_RC6_VID(mv)		(((mv) / 5) - 245) < 0 ?: 0
+#define   GEN6_DECODE_RC6_VID(vids)		(((vids) * 5) > 0 ? ((vids) * 5) + 245 : 0)
 #define GEN6_PCODE_DATA				0x138128
 #define   GEN6_PCODE_FREQ_IA_RATIO_SHIFT	8
 

drivers/gpu/drm/i915/intel_pm.c

@@ -2404,7 +2404,7 @@ static void gen6_enable_rps(struct drm_device *dev)
 	struct intel_ring_buffer *ring;
 	u32 rp_state_cap;
 	u32 gt_perf_status;
-	u32 pcu_mbox, rc6_mask = 0;
+	u32 rc6vids, pcu_mbox, rc6_mask = 0;
 	u32 gtfifodbg;
 	int rc6_mode;
 	int i, ret;
@@ -2526,6 +2526,20 @@ static void gen6_enable_rps(struct drm_device *dev)
 	/* enable all PM interrupts */
 	I915_WRITE(GEN6_PMINTRMSK, 0);
 
+	rc6vids = 0;
+	ret = sandybridge_pcode_read(dev_priv, GEN6_PCODE_READ_RC6VIDS, &rc6vids);
+	if (IS_GEN6(dev) && ret) {
+		DRM_DEBUG_DRIVER("Couldn't check for BIOS workaround\n");
+	} else if (IS_GEN6(dev) && (GEN6_DECODE_RC6_VID(rc6vids & 0xff) < 450)) {
+		DRM_DEBUG_DRIVER("You should update your BIOS. Correcting minimum rc6 voltage (%dmV->%dmV)\n",
+			  GEN6_DECODE_RC6_VID(rc6vids & 0xff), 450);
+		rc6vids &= 0xffff00;
+		rc6vids |= GEN6_ENCODE_RC6_VID(450);
+		ret = sandybridge_pcode_write(dev_priv, GEN6_PCODE_WRITE_RC6VIDS, rc6vids);
+		if (ret)
+			DRM_ERROR("Couldn't fix incorrect rc6 voltage\n");
+	}
+
 	gen6_gt_force_wake_put(dev_priv);
 }