提交 234a56c8 编写于 作者: L Linus Torvalds

Merge tag 'hwmon-for-linus-v4.2' of...

Merge tag 'hwmon-for-linus-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:

 - new driver for Microchip TC74

 - support for ncpXXwf104 added to ntc_thermistor driver

 - minor cleanup

* tag 'hwmon-for-linus-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: add driver for Microchip TC74
  hwmon: (ntc_thermistor) Improve precision of resistance calculation
  hwmon: (ntc_thermistor) fix iio raw to microvolts conversion
  hwmon: (atxp1) Drop auto-detection
  hwmon: (atxp1) Drop FSF mailing address
  hwmon: Allow compile test of GPIO consumers if !GPIOLIB
  hwmon: (sht15) Constify platform_device_id
  hwmon: (max197) Constify platform_device_id
  hwmon: (ntc_thermistor) Add support for ncpXXwf104
......@@ -9,6 +9,7 @@ Requires node properties:
"murata,ncp21wb473"
"murata,ncp03wb473"
"murata,ncp15wl333"
"murata,ncp03wf104"
/* Usage of vendor name "ntc" is deprecated */
<DEPRECATED> "ntc,ncp15wb473"
......
......@@ -2,8 +2,10 @@ Kernel driver ntc_thermistor
=================
Supported thermistors from Murata:
* Murata NTC Thermistors NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473, NCP15WL333
Prefixes: 'ncp15wb473', 'ncp18wb473', 'ncp21wb473', 'ncp03wb473', 'ncp15wl333'
* Murata NTC Thermistors NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473,
NCP15WL333, NCP03WF104
Prefixes: 'ncp15wb473', 'ncp18wb473', 'ncp21wb473', 'ncp03wb473',
'ncp15wl333', 'ncp03wf104'
Datasheet: Publicly available at Murata
Supported thermistors from EPCOS:
......
Kernel driver tc74
====================
Supported chips:
* Microchip TC74
Prefix: 'tc74'
Datasheet: Publicly available at Microchip website.
Description
-----------
Driver supports the above part.
The tc74 has an 8-bit sensor, with 1 degree centigrade resolution
and +- 2 degrees centigrade accuracy.
Notes
-----
Currently entering low power standby mode is not supported.
......@@ -509,7 +509,7 @@ config SENSORS_G762
config SENSORS_GPIO_FAN
tristate "GPIO fan"
depends on GPIOLIB
depends on GPIOLIB || COMPILE_TEST
depends on THERMAL || THERMAL=n
help
If you say yes here you get support for fans connected to GPIO lines.
......@@ -1106,8 +1106,8 @@ config SENSORS_NTC_THERMISTOR
send notifications about the temperature.
Currently, this driver supports
NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473, and NCP15WL333
from Murata and B57330V2103 from EPCOS.
NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473, NCP15WL333,
and NCP03WF104 from Murata and B57330V2103 from EPCOS.
This driver can also be built as a module. If so, the module
will be called ntc-thermistor.
......@@ -1186,7 +1186,7 @@ config SENSORS_PWM_FAN
config SENSORS_SHT15
tristate "Sensiron humidity and temperature sensors. SHT15 and compat."
depends on GPIOLIB
depends on GPIOLIB || COMPILE_TEST
help
If you say yes here you get support for the Sensiron SHT10, SHT11,
SHT15, SHT71, SHT75 humidity and temperature sensors.
......@@ -1452,6 +1452,16 @@ config SENSORS_INA2XX
This driver can also be built as a module. If so, the module
will be called ina2xx.
config SENSORS_TC74
tristate "Microchip TC74"
depends on I2C
help
If you say yes here you get support for Microchip TC74 single
input temperature sensor chips.
This driver can also be built as a module. If so, the module
will be called tc74.
config SENSORS_THMC50
tristate "Texas Instruments THMC50 / Analog Devices ADM1022"
depends on I2C
......
......@@ -140,6 +140,7 @@ obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc47b397.o
obj-$(CONFIG_SENSORS_SMSC47M1) += smsc47m1.o
obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o
obj-$(CONFIG_SENSORS_AMC6821) += amc6821.o
obj-$(CONFIG_SENSORS_TC74) += tc74.o
obj-$(CONFIG_SENSORS_THMC50) += thmc50.o
obj-$(CONFIG_SENSORS_TMP102) += tmp102.o
obj-$(CONFIG_SENSORS_TMP103) += tmp103.o
......
......@@ -12,10 +12,9 @@
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
* The ATXP1 can reside on I2C addresses 0x37 or 0x4e. The chip is
* not auto-detected by the driver and must be instantiated explicitly.
* See Documentation/i2c/instantiating-devices for more information.
*/
#include <linux/kernel.h>
......@@ -43,8 +42,6 @@ MODULE_AUTHOR("Sebastian Witt <se.witt@gmx.net>");
#define ATXP1_VIDMASK 0x1f
#define ATXP1_GPIO1MASK 0x0f
static const unsigned short normal_i2c[] = { 0x37, 0x4e, I2C_CLIENT_END };
struct atxp1_data {
struct i2c_client *client;
struct mutex update_lock;
......@@ -259,48 +256,6 @@ static struct attribute *atxp1_attrs[] = {
};
ATTRIBUTE_GROUPS(atxp1);
/* Return 0 if detection is successful, -ENODEV otherwise */
static int atxp1_detect(struct i2c_client *new_client,
struct i2c_board_info *info)
{
struct i2c_adapter *adapter = new_client->adapter;
u8 temp;
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
return -ENODEV;
/* Detect ATXP1, checking if vendor ID registers are all zero */
if (!((i2c_smbus_read_byte_data(new_client, 0x3e) == 0) &&
(i2c_smbus_read_byte_data(new_client, 0x3f) == 0) &&
(i2c_smbus_read_byte_data(new_client, 0xfe) == 0) &&
(i2c_smbus_read_byte_data(new_client, 0xff) == 0)))
return -ENODEV;
/*
* No vendor ID, now checking if registers 0x10,0x11 (non-existent)
* showing the same as register 0x00
*/
temp = i2c_smbus_read_byte_data(new_client, 0x00);
if (!((i2c_smbus_read_byte_data(new_client, 0x10) == temp) &&
(i2c_smbus_read_byte_data(new_client, 0x11) == temp)))
return -ENODEV;
/* Get VRM */
temp = vid_which_vrm();
if ((temp != 90) && (temp != 91)) {
dev_err(&adapter->dev, "atxp1: Not supporting VRM %d.%d\n",
temp / 10, temp % 10);
return -ENODEV;
}
strlcpy(info->type, "atxp1", I2C_NAME_SIZE);
return 0;
}
static int atxp1_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
......@@ -314,6 +269,11 @@ static int atxp1_probe(struct i2c_client *client,
/* Get VRM */
data->vrm = vid_which_vrm();
if (data->vrm != 90 && data->vrm != 91) {
dev_err(dev, "atxp1: Not supporting VRM %d.%d\n",
data->vrm / 10, data->vrm % 10);
return -ENODEV;
}
data->client = client;
mutex_init(&data->update_lock);
......@@ -342,8 +302,6 @@ static struct i2c_driver atxp1_driver = {
},
.probe = atxp1_probe,
.id_table = atxp1_id,
.detect = atxp1_detect,
.address_list = normal_i2c,
};
module_i2c_driver(atxp1_driver);
......@@ -324,7 +324,7 @@ static int max197_remove(struct platform_device *pdev)
return 0;
}
static struct platform_device_id max197_device_ids[] = {
static const struct platform_device_id max197_device_ids[] = {
{ "max197", max197 },
{ "max199", max199 },
{ }
......
......@@ -53,6 +53,7 @@ static const struct platform_device_id ntc_thermistor_id[] = {
{ "ncp03wb473", TYPE_NCPXXWB473 },
{ "ncp15wl333", TYPE_NCPXXWL333 },
{ "b57330v2103", TYPE_B57330V2103},
{ "ncp03wf104", TYPE_NCPXXWF104 },
{ },
};
......@@ -135,6 +136,43 @@ static const struct ntc_compensation ncpXXwl333[] = {
{ .temp_c = 125, .ohm = 707 },
};
static const struct ntc_compensation ncpXXwf104[] = {
{ .temp_c = -40, .ohm = 4397119 },
{ .temp_c = -35, .ohm = 3088599 },
{ .temp_c = -30, .ohm = 2197225 },
{ .temp_c = -25, .ohm = 1581881 },
{ .temp_c = -20, .ohm = 1151037 },
{ .temp_c = -15, .ohm = 846579 },
{ .temp_c = -10, .ohm = 628988 },
{ .temp_c = -5, .ohm = 471632 },
{ .temp_c = 0, .ohm = 357012 },
{ .temp_c = 5, .ohm = 272500 },
{ .temp_c = 10, .ohm = 209710 },
{ .temp_c = 15, .ohm = 162651 },
{ .temp_c = 20, .ohm = 127080 },
{ .temp_c = 25, .ohm = 100000 },
{ .temp_c = 30, .ohm = 79222 },
{ .temp_c = 35, .ohm = 63167 },
{ .temp_c = 40, .ohm = 50677 },
{ .temp_c = 45, .ohm = 40904 },
{ .temp_c = 50, .ohm = 33195 },
{ .temp_c = 55, .ohm = 27091 },
{ .temp_c = 60, .ohm = 22224 },
{ .temp_c = 65, .ohm = 18323 },
{ .temp_c = 70, .ohm = 15184 },
{ .temp_c = 75, .ohm = 12635 },
{ .temp_c = 80, .ohm = 10566 },
{ .temp_c = 85, .ohm = 8873 },
{ .temp_c = 90, .ohm = 7481 },
{ .temp_c = 95, .ohm = 6337 },
{ .temp_c = 100, .ohm = 5384 },
{ .temp_c = 105, .ohm = 4594 },
{ .temp_c = 110, .ohm = 3934 },
{ .temp_c = 115, .ohm = 3380 },
{ .temp_c = 120, .ohm = 2916 },
{ .temp_c = 125, .ohm = 2522 },
};
/*
* The following compensation table is from the specification of EPCOS NTC
* Thermistors Datasheet
......@@ -190,20 +228,21 @@ struct ntc_data {
static int ntc_adc_iio_read(struct ntc_thermistor_platform_data *pdata)
{
struct iio_channel *channel = pdata->chan;
s64 result;
int val, ret;
int raw, uv, ret;
ret = iio_read_channel_raw(channel, &val);
ret = iio_read_channel_raw(channel, &raw);
if (ret < 0) {
pr_err("read channel() error: %d\n", ret);
return ret;
}
/* unit: mV */
result = pdata->pullup_uv * (s64) val;
result >>= 12;
ret = iio_convert_raw_to_processed(channel, raw, &uv, 1000);
if (ret < 0) {
/* Assume 12 bit ADC with vref at pullup_uv */
uv = (pdata->pullup_uv * (s64)raw) >> 12;
}
return (int)result;
return uv;
}
static const struct of_device_id ntc_match[] = {
......@@ -219,6 +258,8 @@ static const struct of_device_id ntc_match[] = {
.data = &ntc_thermistor_id[4] },
{ .compatible = "epcos,b57330v2103",
.data = &ntc_thermistor_id[5]},
{ .compatible = "murata,ncp03wf104",
.data = &ntc_thermistor_id[6] },
/* Usage of vendor name "ntc" is deprecated */
{ .compatible = "ntc,ncp15wb473",
......@@ -309,30 +350,27 @@ static inline u64 div64_u64_safe(u64 dividend, u64 divisor)
static int get_ohm_of_thermistor(struct ntc_data *data, unsigned int uv)
{
struct ntc_thermistor_platform_data *pdata = data->pdata;
u64 mv = uv / 1000;
u64 pmv = pdata->pullup_uv / 1000;
u32 puv = pdata->pullup_uv;
u64 n, puo, pdo;
puo = pdata->pullup_ohm;
pdo = pdata->pulldown_ohm;
if (mv == 0) {
if (pdata->connect == NTC_CONNECTED_POSITIVE)
return INT_MAX;
return 0;
}
if (mv >= pmv)
if (uv == 0)
return (pdata->connect == NTC_CONNECTED_POSITIVE) ?
INT_MAX : 0;
if (uv >= puv)
return (pdata->connect == NTC_CONNECTED_POSITIVE) ?
0 : INT_MAX;
if (pdata->connect == NTC_CONNECTED_POSITIVE && puo == 0)
n = div64_u64_safe(pdo * (pmv - mv), mv);
n = div_u64(pdo * (puv - uv), uv);
else if (pdata->connect == NTC_CONNECTED_GROUND && pdo == 0)
n = div64_u64_safe(puo * mv, pmv - mv);
n = div_u64(puo * uv, puv - uv);
else if (pdata->connect == NTC_CONNECTED_POSITIVE)
n = div64_u64_safe(pdo * puo * (pmv - mv),
puo * mv - pdo * (pmv - mv));
n = div64_u64_safe(pdo * puo * (puv - uv),
puo * uv - pdo * (puv - uv));
else
n = div64_u64_safe(pdo * puo * mv, pdo * (pmv - mv) - puo * mv);
n = div64_u64_safe(pdo * puo * uv, pdo * (puv - uv) - puo * uv);
if (n > INT_MAX)
n = INT_MAX;
......@@ -567,6 +605,10 @@ static int ntc_thermistor_probe(struct platform_device *pdev)
data->comp = b57330v2103;
data->n_comp = ARRAY_SIZE(b57330v2103);
break;
case TYPE_NCPXXWF104:
data->comp = ncpXXwf104;
data->n_comp = ARRAY_SIZE(ncpXXwf104);
break;
default:
dev_err(&pdev->dev, "Unknown device type: %lu(%s)\n",
pdev_id->driver_data, pdev_id->name);
......
......@@ -1074,7 +1074,7 @@ static int sht15_remove(struct platform_device *pdev)
return 0;
}
static struct platform_device_id sht15_device_ids[] = {
static const struct platform_device_id sht15_device_ids[] = {
{ "sht10", sht10 },
{ "sht11", sht11 },
{ "sht15", sht15 },
......
/*
* An hwmon driver for the Microchip TC74
*
* Copyright 2015 Maciej Szmigiero <mail@maciej.szmigiero.name>
*
* Based on ad7414.c:
* Copyright 2006 Stefan Roese, DENX Software Engineering
* Copyright 2008 Sean MacLennan, PIKA Technologies
* Copyright 2008 Frank Edelhaeuser, Spansion Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#include <linux/bitops.h>
#include <linux/err.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/i2c.h>
#include <linux/jiffies.h>
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/slab.h>
#include <linux/sysfs.h>
/* TC74 registers */
#define TC74_REG_TEMP 0x00
#define TC74_REG_CONFIG 0x01
struct tc74_data {
struct i2c_client *client;
struct mutex lock; /* atomic read data updates */
bool valid; /* validity of fields below */
unsigned long next_update; /* In jiffies */
s8 temp_input; /* Temp value in dC */
};
static int tc74_update_device(struct device *dev)
{
struct tc74_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
int ret;
ret = mutex_lock_interruptible(&data->lock);
if (ret)
return ret;
if (time_after(jiffies, data->next_update) || !data->valid) {
s32 value;
value = i2c_smbus_read_byte_data(client, TC74_REG_CONFIG);
if (value < 0) {
dev_dbg(&client->dev, "TC74_REG_CONFIG read err %d\n",
(int)value);
ret = value;
goto ret_unlock;
}
if (!(value & BIT(6))) {
/* not ready yet */
ret = -EAGAIN;
goto ret_unlock;
}
value = i2c_smbus_read_byte_data(client, TC74_REG_TEMP);
if (value < 0) {
dev_dbg(&client->dev, "TC74_REG_TEMP read err %d\n",
(int)value);
ret = value;
goto ret_unlock;
}
data->temp_input = value;
data->next_update = jiffies + HZ / 4;
data->valid = true;
}
ret_unlock:
mutex_unlock(&data->lock);
return ret;
}
static ssize_t show_temp_input(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct tc74_data *data = dev_get_drvdata(dev);
int ret;
ret = tc74_update_device(dev);
if (ret)
return ret;
return sprintf(buf, "%d\n", data->temp_input * 1000);
}
static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp_input, NULL, 0);
static struct attribute *tc74_attrs[] = {
&sensor_dev_attr_temp1_input.dev_attr.attr,
NULL
};
ATTRIBUTE_GROUPS(tc74);
static int tc74_probe(struct i2c_client *client,
const struct i2c_device_id *dev_id)
{
struct device *dev = &client->dev;
struct tc74_data *data;
struct device *hwmon_dev;
s32 conf;
if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA))
return -EOPNOTSUPP;
data = devm_kzalloc(dev, sizeof(struct tc74_data), GFP_KERNEL);
if (!data)
return -ENOMEM;
data->client = client;
mutex_init(&data->lock);
/* Make sure the chip is powered up. */
conf = i2c_smbus_read_byte_data(client, TC74_REG_CONFIG);
if (conf < 0) {
dev_err(dev, "unable to read config register\n");
return conf;
}
if (conf & 0x3f) {
dev_err(dev, "invalid config register value\n");
return -ENODEV;
}
if (conf & BIT(7)) {
s32 ret;
conf &= ~BIT(7);
ret = i2c_smbus_write_byte_data(client, TC74_REG_CONFIG, conf);
if (ret)
dev_warn(dev, "unable to disable STANDBY\n");
}
hwmon_dev = devm_hwmon_device_register_with_groups(dev,
client->name,
data, tc74_groups);
return PTR_ERR_OR_ZERO(hwmon_dev);
}
static const struct i2c_device_id tc74_id[] = {
{ "tc74", 0 },
{}
};
MODULE_DEVICE_TABLE(i2c, tc74_id);
static struct i2c_driver tc74_driver = {
.driver = {
.name = "tc74",
},
.probe = tc74_probe,
.id_table = tc74_id,
};
module_i2c_driver(tc74_driver);
MODULE_AUTHOR("Maciej Szmigiero <mail@maciej.szmigiero.name>");
MODULE_DESCRIPTION("TC74 driver");
MODULE_LICENSE("GPL");
......@@ -27,6 +27,7 @@ enum ntc_thermistor_type {
TYPE_NCPXXWB473,
TYPE_NCPXXWL333,
TYPE_B57330V2103,
TYPE_NCPXXWF104,
};
struct ntc_thermistor_platform_data {
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册