mac80211.h 57.7 KB
Newer Older
1
/*
2 3
 * mac80211 <-> driver interface
 *
4 5
 * Copyright 2002-2005, Devicescape Software, Inc.
 * Copyright 2006-2007	Jiri Benc <jbenc@suse.cz>
6
 * Copyright 2007	Johannes Berg <johannes@sipsolutions.net>
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#ifndef MAC80211_H
#define MAC80211_H

#include <linux/kernel.h>
#include <linux/if_ether.h>
#include <linux/skbuff.h>
#include <linux/wireless.h>
#include <linux/device.h>
#include <linux/ieee80211.h>
#include <net/wireless.h>
#include <net/cfg80211.h>

25 26 27 28 29 30 31 32 33 34 35 36 37
/**
 * DOC: Introduction
 *
 * mac80211 is the Linux stack for 802.11 hardware that implements
 * only partial functionality in hard- or firmware. This document
 * defines the interface between mac80211 and low-level hardware
 * drivers.
 */

/**
 * DOC: Calling mac80211 from interrupts
 *
 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
38 39 40
 * called in hardware interrupt context. The low-level driver must not call any
 * other functions in hardware interrupt context. If there is a need for such
 * call, the low-level driver should first ACK the interrupt and perform the
41 42 43 44 45
 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
 * tasklet function.
 *
 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also
 *	 use the non-irqsafe functions!
46 47
 */

48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73
/**
 * DOC: Warning
 *
 * If you're reading this document and not the header file itself, it will
 * be incomplete because not all documentation has been converted yet.
 */

/**
 * DOC: Frame format
 *
 * As a general rule, when frames are passed between mac80211 and the driver,
 * they start with the IEEE 802.11 header and include the same octets that are
 * sent over the air except for the FCS which should be calculated by the
 * hardware.
 *
 * There are, however, various exceptions to this rule for advanced features:
 *
 * The first exception is for hardware encryption and decryption offload
 * where the IV/ICV may or may not be generated in hardware.
 *
 * Secondly, when the hardware handles fragmentation, the frame handed to
 * the driver from mac80211 is the MSDU, not the MPDU.
 *
 * Finally, for received frames, the driver is able to indicate that it has
 * filled a radiotap header and put that in front of the frame; if it does
 * not do so then mac80211 may add this under certain circumstances.
74 75
 */

76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91
/**
 * struct ieee80211_ht_bss_info - describing BSS's HT characteristics
 *
 * This structure describes most essential parameters needed
 * to describe 802.11n HT characteristics in a BSS
 *
 * @primary_channel: channel number of primery channel
 * @bss_cap: 802.11n's general BSS capabilities (e.g. channel width)
 * @bss_op_mode: 802.11n's BSS operation modes (e.g. HT protection)
 */
struct ieee80211_ht_bss_info {
	u8 primary_channel;
	u8 bss_cap;  /* use IEEE80211_HT_IE_CHA_ */
	u8 bss_op_mode; /* use IEEE80211_HT_IE_ */
};

J
Johannes Berg 已提交
92 93 94 95
/**
 * struct ieee80211_tx_queue_params - transmit queue configuration
 *
 * The information provided in this structure is required for QoS
96
 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
J
Johannes Berg 已提交
97 98 99 100 101
 *
 * @aifs: arbitration interface space [0..255, -1: use default]
 * @cw_min: minimum contention window [will be a value of the form
 *	2^n-1 in the range 1..1023; 0: use default]
 * @cw_max: maximum contention window [like @cw_min]
102
 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
J
Johannes Berg 已提交
103
 */
104
struct ieee80211_tx_queue_params {
105 106 107 108
	s16 aifs;
	u16 cw_min;
	u16 cw_max;
	u16 txop;
109 110
};

J
Johannes Berg 已提交
111 112 113 114 115 116 117
/**
 * struct ieee80211_tx_queue_stats_data - transmit queue statistics
 *
 * @len: number of packets in queue
 * @limit: queue length limit
 * @count: number of frames sent
 */
118
struct ieee80211_tx_queue_stats_data {
J
Johannes Berg 已提交
119 120 121
	unsigned int len;
	unsigned int limit;
	unsigned int count;
122 123
};

J
Johannes Berg 已提交
124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139
/**
 * enum ieee80211_tx_queue - transmit queue number
 *
 * These constants are used with some callbacks that take a
 * queue number to set parameters for a queue.
 *
 * @IEEE80211_TX_QUEUE_DATA0: data queue 0
 * @IEEE80211_TX_QUEUE_DATA1: data queue 1
 * @IEEE80211_TX_QUEUE_DATA2: data queue 2
 * @IEEE80211_TX_QUEUE_DATA3: data queue 3
 * @IEEE80211_TX_QUEUE_DATA4: data queue 4
 * @IEEE80211_TX_QUEUE_SVP: ??
 * @NUM_TX_DATA_QUEUES: number of data queues
 * @IEEE80211_TX_QUEUE_AFTER_BEACON: transmit queue for frames to be
 *	sent after a beacon
 * @IEEE80211_TX_QUEUE_BEACON: transmit queue for beacon frames
140
 * @NUM_TX_DATA_QUEUES_AMPDU: adding more queues for A-MPDU
J
Johannes Berg 已提交
141 142
 */
enum ieee80211_tx_queue {
143 144 145 146 147 148 149 150 151 152 153 154 155
	IEEE80211_TX_QUEUE_DATA0,
	IEEE80211_TX_QUEUE_DATA1,
	IEEE80211_TX_QUEUE_DATA2,
	IEEE80211_TX_QUEUE_DATA3,
	IEEE80211_TX_QUEUE_DATA4,
	IEEE80211_TX_QUEUE_SVP,

	NUM_TX_DATA_QUEUES,

/* due to stupidity in the sub-ioctl userspace interface, the items in
 * this struct need to have fixed values. As soon as it is removed, we can
 * fix these entries. */
	IEEE80211_TX_QUEUE_AFTER_BEACON = 6,
156 157
	IEEE80211_TX_QUEUE_BEACON = 7,
	NUM_TX_DATA_QUEUES_AMPDU = 16
158 159 160
};

struct ieee80211_tx_queue_stats {
161
	struct ieee80211_tx_queue_stats_data data[NUM_TX_DATA_QUEUES_AMPDU];
162 163 164 165 166 167 168 169 170
};

struct ieee80211_low_level_stats {
	unsigned int dot11ACKFailureCount;
	unsigned int dot11RTSFailureCount;
	unsigned int dot11FCSErrorCount;
	unsigned int dot11RTSSuccessCount;
};

171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207
/**
 * enum ieee80211_bss_change - BSS change notification flags
 *
 * These flags are used with the bss_info_changed() callback
 * to indicate which BSS parameter changed.
 *
 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
 *	also implies a change in the AID.
 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
 */
enum ieee80211_bss_change {
	BSS_CHANGED_ASSOC		= 1<<0,
	BSS_CHANGED_ERP_CTS_PROT	= 1<<1,
	BSS_CHANGED_ERP_PREAMBLE	= 1<<2,
};

/**
 * struct ieee80211_bss_conf - holds the BSS's changing parameters
 *
 * This structure keeps information about a BSS (and an association
 * to that BSS) that can change during the lifetime of the BSS.
 *
 * @assoc: association status
 * @aid: association ID number, valid only when @assoc is true
 * @use_cts_prot: use CTS protection
 * @use_short_preamble: use 802.11b short preamble
 */
struct ieee80211_bss_conf {
	/* association related data */
	bool assoc;
	u16 aid;
	/* erp related data */
	bool use_cts_prot;
	bool use_short_preamble;
};

208 209 210 211 212
/* Transmit control fields. This data structure is passed to low-level driver
 * with each TX frame. The low-level driver is responsible for configuring
 * the hardware to use given values (depending on what is supported). */

struct ieee80211_tx_control {
213
	struct ieee80211_vif *vif;
214 215 216 217 218 219 220
	struct ieee80211_rate *tx_rate;

	/* Transmit rate for RTS/CTS frame */
	struct ieee80211_rate *rts_cts_rate;

	/* retry rate for the last retries */
	struct ieee80211_rate *alt_retry_rate;
221 222 223 224 225 226 227 228 229 230 231 232 233 234

#define IEEE80211_TXCTL_REQ_TX_STATUS	(1<<0)/* request TX status callback for
						* this frame */
#define IEEE80211_TXCTL_DO_NOT_ENCRYPT	(1<<1) /* send this frame without
						* encryption; e.g., for EAPOL
						* frames */
#define IEEE80211_TXCTL_USE_RTS_CTS	(1<<2) /* use RTS-CTS before sending
						* frame */
#define IEEE80211_TXCTL_USE_CTS_PROTECT	(1<<3) /* use CTS protection for the
						* frame (e.g., for combined
						* 802.11g / 802.11b networks) */
#define IEEE80211_TXCTL_NO_ACK		(1<<4) /* tell the low level not to
						* wait for an ack */
#define IEEE80211_TXCTL_RATE_CTRL_PROBE	(1<<5)
235 236
#define IEEE80211_TXCTL_CLEAR_PS_FILT	(1<<6) /* clear powersave filter
						* for destination station */
237 238 239
#define IEEE80211_TXCTL_REQUEUE		(1<<7)
#define IEEE80211_TXCTL_FIRST_FRAGMENT	(1<<8) /* this is a first fragment of
						* the frame */
240
#define IEEE80211_TXCTL_SHORT_PREAMBLE	(1<<9)
241 242 243 244
#define IEEE80211_TXCTL_LONG_RETRY_LIMIT (1<<10) /* this frame should be send
						  * using the through
						  * set_retry_limit configured
						  * long retry value */
245
#define IEEE80211_TXCTL_EAPOL_FRAME	(1<<11) /* internal to mac80211 */
246 247
#define IEEE80211_TXCTL_SEND_AFTER_DTIM	(1<<12) /* send this frame after DTIM
						 * beacon */
248 249
#define IEEE80211_TXCTL_AMPDU		(1<<13) /* this frame should be sent
						 * as part of an A-MPDU */
250 251
	u32 flags;			       /* tx control flags defined
						* above */
252 253
	u8 key_idx;		/* keyidx from hw->set_key(), undefined if
				 * IEEE80211_TXCTL_DO_NOT_ENCRYPT is set */
254 255 256
	u8 retry_limit;		/* 1 = only first attempt, 2 = one retry, ..
				 * This could be used when set_retry_limit
				 * is not implemented by the driver */
257 258 259 260 261 262 263 264
	u8 antenna_sel_tx; 	/* 0 = default/diversity, 1 = Ant0, 2 = Ant1 */
	u8 icv_len;		/* length of the ICV/MIC field in octets */
	u8 iv_len;		/* length of the IV field in octets */
	u8 queue;		/* hardware queue to use for this frame;
				 * 0 = highest, hw->queues-1 = lowest */
	int type;	/* internal */
};

265 266 267 268 269 270 271 272 273 274 275 276 277 278

/**
 * enum mac80211_rx_flags - receive flags
 *
 * These flags are used with the @flag member of &struct ieee80211_rx_status.
 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
 *	Use together with %RX_FLAG_MMIC_STRIPPED.
 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
 * @RX_FLAG_RADIOTAP: This frame starts with a radiotap header.
 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
 *	verification has been done by the hardware.
 * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame.
 *	If this flag is set, the stack cannot do any replay detection
 *	hence the driver or hardware will have to do that.
279 280 281 282
 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
 *	the frame.
 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
 *	the frame.
283
 * @RX_FLAG_TSFT: The timestamp passed in the RX status (@mactime field)
B
Bruno Randolf 已提交
284 285
 *	is valid. This is useful in monitor mode and necessary for beacon frames
 *	to enable IBSS merging.
286 287 288 289 290 291 292
 */
enum mac80211_rx_flags {
	RX_FLAG_MMIC_ERROR	= 1<<0,
	RX_FLAG_DECRYPTED	= 1<<1,
	RX_FLAG_RADIOTAP	= 1<<2,
	RX_FLAG_MMIC_STRIPPED	= 1<<3,
	RX_FLAG_IV_STRIPPED	= 1<<4,
293 294
	RX_FLAG_FAILED_FCS_CRC	= 1<<5,
	RX_FLAG_FAILED_PLCP_CRC = 1<<6,
295
	RX_FLAG_TSFT		= 1<<7,
296 297 298 299 300 301 302 303
};

/**
 * struct ieee80211_rx_status - receive status
 *
 * The low-level driver should provide this information (the subset
 * supported by hardware) to the 802.11 code with each received
 * frame.
304 305
 * @mactime: value in microseconds of the 64-bit Time Synchronization Function
 * 	(TSF) timer when the first data symbol (MPDU) arrived at the hardware.
306
 * @band: the active band when this frame was received
307 308 309 310 311
 * @freq: frequency the radio was tuned to when receiving this frame, in MHz
 * @ssi: signal strength when receiving this frame
 * @signal: used as 'qual' in statistics reporting
 * @noise: PHY noise when receiving this frame
 * @antenna: antenna used
312
 * @rate_idx: index of data rate into band's supported rates
313 314
 * @flag: %RX_FLAG_*
 */
315 316
struct ieee80211_rx_status {
	u64 mactime;
317
	enum ieee80211_band band;
318
	int freq;
319
	int ssi;
320
	int signal;
321 322
	int noise;
	int antenna;
323
	int rate_idx;
324 325 326
	int flag;
};

J
Johannes Berg 已提交
327 328 329 330 331 332 333 334
/**
 * enum ieee80211_tx_status_flags - transmit status flags
 *
 * Status flags to indicate various transmit conditions.
 *
 * @IEEE80211_TX_STATUS_TX_FILTERED: The frame was not transmitted
 *	because the destination STA was in powersave mode.
 * @IEEE80211_TX_STATUS_ACK: Frame was acknowledged
335 336
 * @IEEE80211_TX_STATUS_AMPDU: The frame was aggregated, so status
 * 	is for the whole aggregation.
J
Johannes Berg 已提交
337 338 339 340
 */
enum ieee80211_tx_status_flags {
	IEEE80211_TX_STATUS_TX_FILTERED	= 1<<0,
	IEEE80211_TX_STATUS_ACK		= 1<<1,
341
	IEEE80211_TX_STATUS_AMPDU	= 1<<2,
J
Johannes Berg 已提交
342 343 344 345 346 347 348 349 350 351 352
};

/**
 * struct ieee80211_tx_status - transmit status
 *
 * As much information as possible should be provided for each transmitted
 * frame with ieee80211_tx_status().
 *
 * @control: a copy of the &struct ieee80211_tx_control passed to the driver
 *	in the tx() callback.
 * @flags: transmit status flags, defined above
353
 * @retry_count: number of retries
J
Johannes Berg 已提交
354 355
 * @excessive_retries: set to 1 if the frame was retried many times
 *	but not acknowledged
356 357 358 359 360
 * @ampdu_ack_len: number of aggregated frames.
 * 	relevant only if IEEE80211_TX_STATUS_AMPDU was set.
 * @ampdu_ack_map: block ack bit map for the aggregation.
 * 	relevant only if IEEE80211_TX_STATUS_AMPDU was set.
 * @ack_signal: signal strength of the ACK frame
J
Johannes Berg 已提交
361 362 363
 * @queue_length: ?? REMOVE
 * @queue_number: ?? REMOVE
 */
364 365
struct ieee80211_tx_status {
	struct ieee80211_tx_control control;
J
Johannes Berg 已提交
366 367
	u8 flags;
	u8 retry_count;
368 369 370
	bool excessive_retries;
	u8 ampdu_ack_len;
	u64 ampdu_ack_map;
J
Johannes Berg 已提交
371 372
	int ack_signal;
	int queue_length;
373 374 375
	int queue_number;
};

J
Johannes Berg 已提交
376 377 378 379 380 381 382
/**
 * enum ieee80211_conf_flags - configuration flags
 *
 * Flags to define PHY configuration options
 *
 * @IEEE80211_CONF_SHORT_SLOT_TIME: use 802.11g short slot time
 * @IEEE80211_CONF_RADIOTAP: add radiotap header at receive time (if supported)
383
 * @IEEE80211_CONF_SUPPORT_HT_MODE: use 802.11n HT capabilities (if supported)
J
Johannes Berg 已提交
384 385
 */
enum ieee80211_conf_flags {
386 387 388
	IEEE80211_CONF_SHORT_SLOT_TIME	= (1<<0),
	IEEE80211_CONF_RADIOTAP		= (1<<1),
	IEEE80211_CONF_SUPPORT_HT_MODE	= (1<<2),
J
Johannes Berg 已提交
389
};
390 391 392 393 394 395 396

/**
 * struct ieee80211_conf - configuration of the device
 *
 * This struct indicates how the driver shall configure the hardware.
 *
 * @radio_enabled: when zero, driver is required to switch off the radio.
J
Johannes Berg 已提交
397 398 399
 *	TODO make a flag
 * @beacon_int: beacon interval (TODO make interface config)
 * @flags: configuration flags defined above
400 401
 * @power_level: requested transmit power (in dBm)
 * @max_antenna_gain: maximum antenna gain (in dBi)
J
Johannes Berg 已提交
402 403 404
 * @antenna_sel_tx: transmit antenna selection, 0: default/diversity,
 *	1/2: antenna 0/1
 * @antenna_sel_rx: receive antenna selection, like @antenna_sel_tx
405 406
 * @ht_conf: describes current self configuration of 802.11n HT capabilies
 * @ht_bss_conf: describes current BSS configuration of 802.11n HT parameters
407
 * @channel: the channel to tune to
408 409 410 411 412
 */
struct ieee80211_conf {
	int radio_enabled;

	int beacon_int;
J
Johannes Berg 已提交
413
	u32 flags;
414 415
	int power_level;
	int max_antenna_gain;
416 417
	u8 antenna_sel_tx;
	u8 antenna_sel_rx;
418

419 420
	struct ieee80211_channel *channel;

421 422
	struct ieee80211_ht_info ht_conf;
	struct ieee80211_ht_bss_info ht_bss_conf;
423 424 425 426 427
};

/**
 * enum ieee80211_if_types - types of 802.11 network interfaces
 *
428 429
 * @IEEE80211_IF_TYPE_INVALID: invalid interface type, not used
 *	by mac80211 itself
430 431 432 433 434 435 436
 * @IEEE80211_IF_TYPE_AP: interface in AP mode.
 * @IEEE80211_IF_TYPE_MGMT: special interface for communication with hostap
 *	daemon. Drivers should never see this type.
 * @IEEE80211_IF_TYPE_STA: interface in STA (client) mode.
 * @IEEE80211_IF_TYPE_IBSS: interface in IBSS (ad-hoc) mode.
 * @IEEE80211_IF_TYPE_MNTR: interface in monitor (rfmon) mode.
 * @IEEE80211_IF_TYPE_WDS: interface in WDS mode.
437 438
 * @IEEE80211_IF_TYPE_VLAN: VLAN interface bound to an AP, drivers
 *	will never see this type.
J
Johannes Berg 已提交
439
 * @IEEE80211_IF_TYPE_MESH_POINT: 802.11s mesh point
440 441
 */
enum ieee80211_if_types {
442
	IEEE80211_IF_TYPE_INVALID,
443 444 445
	IEEE80211_IF_TYPE_AP,
	IEEE80211_IF_TYPE_STA,
	IEEE80211_IF_TYPE_IBSS,
446
	IEEE80211_IF_TYPE_MESH_POINT,
447 448 449
	IEEE80211_IF_TYPE_MNTR,
	IEEE80211_IF_TYPE_WDS,
	IEEE80211_IF_TYPE_VLAN,
450 451
};

452 453 454 455 456 457
/**
 * struct ieee80211_vif - per-interface data
 *
 * Data in this structure is continually present for driver
 * use during the life of a virtual interface.
 *
458
 * @type: type of this virtual interface
459 460 461 462
 * @drv_priv: data area for driver use, will always be aligned to
 *	sizeof(void *).
 */
struct ieee80211_vif {
463
	enum ieee80211_if_types type;
464 465 466 467
	/* must be last */
	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
};

J
Johannes Berg 已提交
468 469 470 471 472 473 474 475
static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
{
#ifdef CONFIG_MAC80211_MESH
	return vif->type == IEEE80211_IF_TYPE_MESH_POINT;
#endif
	return false;
}

476 477 478
/**
 * struct ieee80211_if_init_conf - initial configuration of an interface
 *
479 480 481
 * @vif: pointer to a driver-use per-interface structure. The pointer
 *	itself is also used for various functions including
 *	ieee80211_beacon_get() and ieee80211_get_buffered_bc().
482 483 484 485 486 487 488 489
 * @type: one of &enum ieee80211_if_types constants. Determines the type of
 *	added/removed interface.
 * @mac_addr: pointer to MAC address of the interface. This pointer is valid
 *	until the interface is removed (i.e. it cannot be used after
 *	remove_interface() callback was called for this interface).
 *
 * This structure is used in add_interface() and remove_interface()
 * callbacks of &struct ieee80211_hw.
490 491 492 493 494 495
 *
 * When you allow multiple interfaces to be added to your PHY, take care
 * that the hardware can actually handle multiple MAC addresses. However,
 * also take care that when there's no interface left with mac_addr != %NULL
 * you remove the MAC address from the device to avoid acknowledging packets
 * in pure monitor mode.
496 497
 */
struct ieee80211_if_init_conf {
498
	enum ieee80211_if_types type;
499
	struct ieee80211_vif *vif;
500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533
	void *mac_addr;
};

/**
 * struct ieee80211_if_conf - configuration of an interface
 *
 * @type: type of the interface. This is always the same as was specified in
 *	&struct ieee80211_if_init_conf. The type of an interface never changes
 *	during the life of the interface; this field is present only for
 *	convenience.
 * @bssid: BSSID of the network we are associated to/creating.
 * @ssid: used (together with @ssid_len) by drivers for hardware that
 *	generate beacons independently. The pointer is valid only during the
 *	config_interface() call, so copy the value somewhere if you need
 *	it.
 * @ssid_len: length of the @ssid field.
 * @beacon: beacon template. Valid only if @host_gen_beacon_template in
 *	&struct ieee80211_hw is set. The driver is responsible of freeing
 *	the sk_buff.
 * @beacon_control: tx_control for the beacon template, this field is only
 *	valid when the @beacon field was set.
 *
 * This structure is passed to the config_interface() callback of
 * &struct ieee80211_hw.
 */
struct ieee80211_if_conf {
	int type;
	u8 *bssid;
	u8 *ssid;
	size_t ssid_len;
	struct sk_buff *beacon;
	struct ieee80211_tx_control *beacon_control;
};

534 535 536 537 538 539
/**
 * enum ieee80211_key_alg - key algorithm
 * @ALG_WEP: WEP40 or WEP104
 * @ALG_TKIP: TKIP
 * @ALG_CCMP: CCMP (AES)
 */
540
enum ieee80211_key_alg {
541 542 543
	ALG_WEP,
	ALG_TKIP,
	ALG_CCMP,
544
};
545

546 547 548 549 550 551 552 553 554 555 556 557 558 559 560

/**
 * enum ieee80211_key_flags - key flags
 *
 * These flags are used for communication about keys between the driver
 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
 *
 * @IEEE80211_KEY_FLAG_WMM_STA: Set by mac80211, this flag indicates
 *	that the STA this key will be used with could be using QoS.
 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
 *	driver to indicate that it requires IV generation for this
 *	particular key.
 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
 *	the driver for a TKIP key if it requires Michael MIC
 *	generation in software.
561
 */
562 563 564 565 566
enum ieee80211_key_flags {
	IEEE80211_KEY_FLAG_WMM_STA	= 1<<0,
	IEEE80211_KEY_FLAG_GENERATE_IV	= 1<<1,
	IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
};
J
Johannes Berg 已提交
567

568 569 570 571 572 573 574 575
/**
 * struct ieee80211_key_conf - key information
 *
 * This key information is given by mac80211 to the driver by
 * the set_key() callback in &struct ieee80211_ops.
 *
 * @hw_key_idx: To be set by the driver, this is the key index the driver
 *	wants to be given when a frame is transmitted and needs to be
576
 *	encrypted in hardware.
577 578 579 580 581 582
 * @alg: The key algorithm.
 * @flags: key flags, see &enum ieee80211_key_flags.
 * @keyidx: the key index (0-3)
 * @keylen: key material length
 * @key: key material
 */
583
struct ieee80211_key_conf {
584
	enum ieee80211_key_alg alg;
585
	u8 hw_key_idx;
J
Johannes Berg 已提交
586 587 588
	u8 flags;
	s8 keyidx;
	u8 keylen;
589 590 591
	u8 key[0];
};

592 593 594 595 596 597 598 599 600
/**
 * enum set_key_cmd - key command
 *
 * Used with the set_key() callback in &struct ieee80211_ops, this
 * indicates whether a key is being removed or added.
 *
 * @SET_KEY: a key is set
 * @DISABLE_KEY: a key must be disabled
 */
601
enum set_key_cmd {
J
Johannes Berg 已提交
602
	SET_KEY, DISABLE_KEY,
603
};
604

605 606 607 608 609 610 611 612 613 614 615 616
/**
 * enum sta_notify_cmd - sta notify command
 *
 * Used with the sta_notify() callback in &struct ieee80211_ops, this
 * indicates addition and removal of a station to station table
 *
 * @STA_NOTIFY_ADD: a station was added to the station table
 * @STA_NOTIFY_REMOVE: a station being removed from the station table
 */
enum sta_notify_cmd {
	STA_NOTIFY_ADD, STA_NOTIFY_REMOVE
};
617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650

/**
 * enum ieee80211_hw_flags - hardware flags
 *
 * These flags are used to indicate hardware capabilities to
 * the stack. Generally, flags here should have their meaning
 * done in a way that the simplest hardware doesn't need setting
 * any particular flags. There are some exceptions to this rule,
 * however, so you are advised to review these flags carefully.
 *
 * @IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE:
 *	The device only needs to be supplied with a beacon template.
 *	If you need the host to generate each beacon then don't use
 *	this flag and call ieee80211_beacon_get() when you need the
 *	next beacon frame. Note that if you set this flag, you must
 *	implement the set_tim() callback for powersave mode to work
 *	properly.
 *	This flag is only relevant for access-point mode.
 *
 * @IEEE80211_HW_RX_INCLUDES_FCS:
 *	Indicates that received frames passed to the stack include
 *	the FCS at the end.
 *
 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
 *	Some wireless LAN chipsets buffer broadcast/multicast frames
 *	for power saving stations in the hardware/firmware and others
 *	rely on the host system for such buffering. This option is used
 *	to configure the IEEE 802.11 upper layer to buffer broadcast and
 *	multicast frames when there are power saving stations so that
 *	the driver can fetch them with ieee80211_get_buffered_bc(). Note
 *	that not setting this flag works properly only when the
 *	%IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is also not set because
 *	otherwise the stack will not know when the DTIM beacon was sent.
 *
651 652 653 654 655 656
 * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
 *	Hardware is not capable of short slot operation on the 2.4 GHz band.
 *
 * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
 *	Hardware is not capable of receiving frames with short preamble on
 *	the 2.4 GHz band.
657 658 659 660 661
 */
enum ieee80211_hw_flags {
	IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE		= 1<<0,
	IEEE80211_HW_RX_INCLUDES_FCS			= 1<<1,
	IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING	= 1<<2,
662 663
	IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE		= 1<<3,
	IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE	= 1<<4,
664 665
};

666 667
/**
 * struct ieee80211_hw - hardware information and state
668 669 670 671 672 673 674
 *
 * This structure contains the configuration and hardware
 * information for an 802.11 PHY.
 *
 * @wiphy: This points to the &struct wiphy allocated for this
 *	802.11 PHY. You must fill in the @perm_addr and @dev
 *	members of this structure using SET_IEEE80211_DEV()
675 676
 *	and SET_IEEE80211_PERM_ADDR(). Additionally, all supported
 *	bands (with channels, bitrates) are registered here.
677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702
 *
 * @conf: &struct ieee80211_conf, device configuration, don't use.
 *
 * @workqueue: single threaded workqueue available for driver use,
 *	allocated by mac80211 on registration and flushed on
 *	unregistration.
 *
 * @priv: pointer to private area that was allocated for driver use
 *	along with this structure.
 *
 * @flags: hardware flags, see &enum ieee80211_hw_flags.
 *
 * @extra_tx_headroom: headroom to reserve in each transmit skb
 *	for use by the driver (e.g. for transmit headers.)
 *
 * @channel_change_time: time (in microseconds) it takes to change channels.
 *
 * @max_rssi: Maximum value for ssi in RX information, use
 *	negative numbers for dBm and 0 to indicate no support.
 *
 * @max_signal: like @max_rssi, but for the signal value.
 *
 * @max_noise: like @max_rssi, but for the noise value.
 *
 * @queues: number of available hardware transmit queues for
 *	data packets. WMM/QoS requires at least four.
703 704 705 706
 *
 * @rate_control_algorithm: rate control algorithm for this hardware.
 *	If unset (NULL), the default algorithm will be used. Must be
 *	set before calling ieee80211_register_hw().
707 708 709
 *
 * @vif_data_size: size (in bytes) of the drv_priv data area
 *	within &struct ieee80211_vif.
710
 */
711 712
struct ieee80211_hw {
	struct ieee80211_conf conf;
713
	struct wiphy *wiphy;
714
	struct workqueue_struct *workqueue;
715
	const char *rate_control_algorithm;
716
	void *priv;
717
	u32 flags;
718 719
	unsigned int extra_tx_headroom;
	int channel_change_time;
720
	int vif_data_size;
721
	u8 queues;
722 723 724 725 726
	s8 max_rssi;
	s8 max_signal;
	s8 max_noise;
};

727 728 729 730 731 732
/**
 * SET_IEEE80211_DEV - set device for 802.11 hardware
 *
 * @hw: the &struct ieee80211_hw to set the device for
 * @dev: the &struct device of this 802.11 device
 */
733 734 735 736 737
static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev)
{
	set_wiphy_dev(hw->wiphy, dev);
}

738 739 740 741 742 743
/**
 * SET_IEEE80211_PERM_ADDR - set the permanenet MAC address for 802.11 hardware
 *
 * @hw: the &struct ieee80211_hw to set the MAC address for
 * @addr: the address to set
 */
744 745 746 747 748
static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr)
{
	memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
}

749 750 751 752 753 754 755 756 757 758 759 760 761 762
/**
 * DOC: Hardware crypto acceleration
 *
 * mac80211 is capable of taking advantage of many hardware
 * acceleration designs for encryption and decryption operations.
 *
 * The set_key() callback in the &struct ieee80211_ops for a given
 * device is called to enable hardware acceleration of encryption and
 * decryption. The callback takes an @address parameter that will be
 * the broadcast address for default keys, the other station's hardware
 * address for individual keys or the zero address for keys that will
 * be used only for transmission.
 * Multiple transmission keys with the same key index may be used when
 * VLANs are configured for an access point.
763
 *
764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786
 * The @local_address parameter will always be set to our own address,
 * this is only relevant if you support multiple local addresses.
 *
 * When transmitting, the TX control data will use the @hw_key_idx
 * selected by the driver by modifying the &struct ieee80211_key_conf
 * pointed to by the @key parameter to the set_key() function.
 *
 * The set_key() call for the %SET_KEY command should return 0 if
 * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be
 * added; if you return 0 then hw_key_idx must be assigned to the
 * hardware key index, you are free to use the full u8 range.
 *
 * When the cmd is %DISABLE_KEY then it must succeed.
 *
 * Note that it is permissible to not decrypt a frame even if a key
 * for it has been uploaded to hardware, the stack will not make any
 * decision based on whether a key has been uploaded or not but rather
 * based on the receive flags.
 *
 * The &struct ieee80211_key_conf structure pointed to by the @key
 * parameter is guaranteed to be valid until another call to set_key()
 * removes it, but it can only be used as a cookie to differentiate
 * keys.
787
 */
788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811

/**
 * DOC: Frame filtering
 *
 * mac80211 requires to see many management frames for proper
 * operation, and users may want to see many more frames when
 * in monitor mode. However, for best CPU usage and power consumption,
 * having as few frames as possible percolate through the stack is
 * desirable. Hence, the hardware should filter as much as possible.
 *
 * To achieve this, mac80211 uses filter flags (see below) to tell
 * the driver's configure_filter() function which frames should be
 * passed to mac80211 and which should be filtered out.
 *
 * The configure_filter() callback is invoked with the parameters
 * @mc_count and @mc_list for the combined multicast address list
 * of all virtual interfaces, @changed_flags telling which flags
 * were changed and @total_flags with the new flag states.
 *
 * If your device has no multicast address filters your driver will
 * need to check both the %FIF_ALLMULTI flag and the @mc_count
 * parameter to see whether multicast frames should be accepted
 * or dropped.
 *
812 813 814 815 816 817 818 819 820 821 822 823
 * All unsupported flags in @total_flags must be cleared.
 * Hardware does not support a flag if it is incapable of _passing_
 * the frame to the stack. Otherwise the driver must ignore
 * the flag, but not clear it.
 * You must _only_ clear the flag (announce no support for the
 * flag to mac80211) if you are not able to pass the packet type
 * to the stack (so the hardware always filters it).
 * So for example, you should clear @FIF_CONTROL, if your hardware
 * always filters control frames. If your hardware always passes
 * control frames to the kernel and is incapable of filtering them,
 * you do _not_ clear the @FIF_CONTROL flag.
 * This rule applies to all other FIF flags as well.
824
 */
825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851 852 853 854 855 856 857

/**
 * enum ieee80211_filter_flags - hardware filter flags
 *
 * These flags determine what the filter in hardware should be
 * programmed to let through and what should not be passed to the
 * stack. It is always safe to pass more frames than requested,
 * but this has negative impact on power consumption.
 *
 * @FIF_PROMISC_IN_BSS: promiscuous mode within your BSS,
 *	think of the BSS as your network segment and then this corresponds
 *	to the regular ethernet device promiscuous mode.
 *
 * @FIF_ALLMULTI: pass all multicast frames, this is used if requested
 *	by the user or if the hardware is not capable of filtering by
 *	multicast address.
 *
 * @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the
 *	%RX_FLAG_FAILED_FCS_CRC for them)
 *
 * @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set
 *	the %RX_FLAG_FAILED_PLCP_CRC for them
 *
 * @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate
 *	to the hardware that it should not filter beacons or probe responses
 *	by BSSID. Filtering them can greatly reduce the amount of processing
 *	mac80211 needs to do and the amount of CPU wakeups, so you should
 *	honour this flag if possible.
 *
 * @FIF_CONTROL: pass control frames, if PROMISC_IN_BSS is not set then
 *	only those addressed to this station
 *
 * @FIF_OTHER_BSS: pass frames destined to other BSSes
858
 */
859 860 861 862 863 864 865 866 867 868
enum ieee80211_filter_flags {
	FIF_PROMISC_IN_BSS	= 1<<0,
	FIF_ALLMULTI		= 1<<1,
	FIF_FCSFAIL		= 1<<2,
	FIF_PLCPFAIL		= 1<<3,
	FIF_BCN_PRBRESP_PROMISC	= 1<<4,
	FIF_CONTROL		= 1<<5,
	FIF_OTHER_BSS		= 1<<6,
};

869 870 871 872 873 874 875
/**
 * enum ieee80211_ampdu_mlme_action - A-MPDU actions
 *
 * These flags are used with the ampdu_action() callback in
 * &struct ieee80211_ops to indicate which action is needed.
 * @IEEE80211_AMPDU_RX_START: start Rx aggregation
 * @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation
876 877
 * @IEEE80211_AMPDU_TX_START: start Tx aggregation
 * @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation
878 879 880 881
 */
enum ieee80211_ampdu_mlme_action {
	IEEE80211_AMPDU_RX_START,
	IEEE80211_AMPDU_RX_STOP,
882 883
	IEEE80211_AMPDU_TX_START,
	IEEE80211_AMPDU_TX_STOP,
884
};
885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940

/**
 * struct ieee80211_ops - callbacks from mac80211 to the driver
 *
 * This structure contains various callbacks that the driver may
 * handle or, in some cases, must handle, for example to configure
 * the hardware to a new channel or to transmit a frame.
 *
 * @tx: Handler that 802.11 module calls for each transmitted frame.
 *	skb contains the buffer starting from the IEEE 802.11 header.
 *	The low-level driver should send the frame out based on
 *	configuration in the TX control data. Must be implemented and
 *	atomic.
 *
 * @start: Called before the first netdevice attached to the hardware
 *	is enabled. This should turn on the hardware and must turn on
 *	frame reception (for possibly enabled monitor interfaces.)
 *	Returns negative error codes, these may be seen in userspace,
 *	or zero.
 *	When the device is started it should not have a MAC address
 *	to avoid acknowledging frames before a non-monitor device
 *	is added.
 *	Must be implemented.
 *
 * @stop: Called after last netdevice attached to the hardware
 *	is disabled. This should turn off the hardware (at least
 *	it must turn off frame reception.)
 *	May be called right after add_interface if that rejects
 *	an interface.
 *	Must be implemented.
 *
 * @add_interface: Called when a netdevice attached to the hardware is
 *	enabled. Because it is not called for monitor mode devices, @open
 *	and @stop must be implemented.
 *	The driver should perform any initialization it needs before
 *	the device can be enabled. The initial configuration for the
 *	interface is given in the conf parameter.
 *	The callback may refuse to add an interface by returning a
 *	negative error code (which will be seen in userspace.)
 *	Must be implemented.
 *
 * @remove_interface: Notifies a driver that an interface is going down.
 *	The @stop callback is called after this if it is the last interface
 *	and no monitor interfaces are present.
 *	When all interfaces are removed, the MAC address in the hardware
 *	must be cleared so the device no longer acknowledges packets,
 *	the mac_addr member of the conf structure is, however, set to the
 *	MAC address of the device going away.
 *	Hence, this callback must be implemented.
 *
 * @config: Handler for configuration requests. IEEE 802.11 code calls this
 *	function to change hardware configuration, e.g., channel.
 *
 * @config_interface: Handler for configuration requests related to interfaces
 *	(e.g. BSSID changes.)
 *
941 942 943 944 945 946 947 948
 * @bss_info_changed: Handler for configuration requests related to BSS
 *	parameters that may vary during BSS's lifespan, and may affect low
 *	level driver (e.g. assoc/disassoc status, erp parameters).
 *	This function should not be used if no BSS has been set, unless
 *	for association indication. The @changed parameter indicates which
 *	of the bss parameters has changed when a call is made. This callback
 *	has to be atomic.
 *
949 950 951 952 953 954 955 956 957 958 959 960 961 962 963
 * @configure_filter: Configure the device's RX filter.
 *	See the section "Frame filtering" for more information.
 *	This callback must be implemented and atomic.
 *
 * @set_tim: Set TIM bit. If the hardware/firmware takes care of beacon
 *	generation (that is, %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is set)
 *	mac80211 calls this function when a TIM bit must be set or cleared
 *	for a given AID. Must be atomic.
 *
 * @set_key: See the section "Hardware crypto acceleration"
 *	This callback can sleep, and is only called between add_interface
 *	and remove_interface calls, i.e. while the interface with the
 *	given local_address is enabled.
 *
 * @hw_scan: Ask the hardware to service the scan request, no need to start
964 965 966
 *	the scan state machine in stack. The scan must honour the channel
 *	configuration done by the regulatory agent in the wiphy's registered
 *	bands.
967 968 969
 *
 * @get_stats: return low-level statistics
 *
970 971 972
 * @get_tkip_seq: If your device implements TKIP encryption in hardware this
 *	callback should be provided to read the TKIP transmit IVs (both IV32
 *	and IV16) for the given key from hardware.
973 974 975 976 977 978 979 980 981
 *
 * @set_rts_threshold: Configuration of RTS threshold (if device needs it)
 *
 * @set_frag_threshold: Configuration of fragmentation threshold. Assign this if
 *	the device does fragmentation by itself; if this method is assigned then
 *	the stack will not do fragmentation.
 *
 * @set_retry_limit: Configuration of retry limits (if device needs it)
 *
982 983
 * @sta_notify: Notifies low level driver about addition or removal
 *	of assocaited station or AP.
984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006
 *
 * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
 *	bursting) for a hardware TX queue. The @queue parameter uses the
 *	%IEEE80211_TX_QUEUE_* constants. Must be atomic.
 *
 * @get_tx_stats: Get statistics of the current TX queue status. This is used
 *	to get number of currently queued packets (queue length), maximum queue
 *	size (limit), and total number of packets sent using each TX queue
 *	(count). This information is used for WMM to find out which TX
 *	queues have room for more packets and by hostapd to provide
 *	statistics about the current queueing state to external programs.
 *
 * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
 *	this is only used for IBSS mode debugging and, as such, is not a
 *	required function. Must be atomic.
 *
 * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize
 *	with other STAs in the IBSS. This is only used in IBSS mode. This
 *	function is optional if the firmware/hardware takes full care of
 *	TSF synchronization.
 *
 * @beacon_update: Setup beacon data for IBSS beacons. Unlike access point,
 *	IBSS uses a fixed beacon frame which is configured using this
1007 1008 1009 1010 1011 1012 1013 1014
 *	function.
 *	If the driver returns success (0) from this callback, it owns
 *	the skb. That means the driver is responsible to kfree_skb() it.
 *	The control structure is not dynamically allocated. That means the
 *	driver does not own the pointer and if it needs it somewhere
 *	outside of the context of this function, it must copy it
 *	somewhere else.
 *	This handler is required only for IBSS mode.
1015 1016 1017 1018
 *
 * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us.
 *	This is needed only for IBSS mode and the result of this function is
 *	used to determine whether to reply to Probe Requests.
1019 1020
 *
 * @conf_ht: Configures low level driver with 802.11n HT data. Must be atomic.
1021 1022 1023 1024 1025
 *
 * @ampdu_action: Perform a certain A-MPDU action
 * 	The RA/TID combination determines the destination and TID we want
 * 	the ampdu action to be performed for. The action is defined through
 * 	ieee80211_ampdu_mlme_action. Starting sequence number (@ssn)
1026 1027
 * 	is the first frame we expect to perform the action on. notice
 * 	that TX/RX_STOP can pass NULL for this parameter.
1028
 */
1029 1030 1031
struct ieee80211_ops {
	int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb,
		  struct ieee80211_tx_control *control);
1032 1033
	int (*start)(struct ieee80211_hw *hw);
	void (*stop)(struct ieee80211_hw *hw);
1034 1035 1036 1037 1038 1039
	int (*add_interface)(struct ieee80211_hw *hw,
			     struct ieee80211_if_init_conf *conf);
	void (*remove_interface)(struct ieee80211_hw *hw,
				 struct ieee80211_if_init_conf *conf);
	int (*config)(struct ieee80211_hw *hw, struct ieee80211_conf *conf);
	int (*config_interface)(struct ieee80211_hw *hw,
1040 1041
				struct ieee80211_vif *vif,
				struct ieee80211_if_conf *conf);
1042 1043 1044 1045
	void (*bss_info_changed)(struct ieee80211_hw *hw,
				 struct ieee80211_vif *vif,
				 struct ieee80211_bss_conf *info,
				 u32 changed);
1046 1047 1048 1049
	void (*configure_filter)(struct ieee80211_hw *hw,
				 unsigned int changed_flags,
				 unsigned int *total_flags,
				 int mc_count, struct dev_addr_list *mc_list);
1050
	int (*set_tim)(struct ieee80211_hw *hw, int aid, int set);
1051
	int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd,
J
Johannes Berg 已提交
1052 1053
		       const u8 *local_address, const u8 *address,
		       struct ieee80211_key_conf *key);
1054 1055 1056
	int (*hw_scan)(struct ieee80211_hw *hw, u8 *ssid, size_t len);
	int (*get_stats)(struct ieee80211_hw *hw,
			 struct ieee80211_low_level_stats *stats);
1057 1058
	void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx,
			     u32 *iv32, u16 *iv16);
1059 1060 1061 1062
	int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);
	int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value);
	int (*set_retry_limit)(struct ieee80211_hw *hw,
			       u32 short_retry, u32 long_retr);
1063
	void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
1064
			enum sta_notify_cmd, const u8 *addr);
1065 1066 1067 1068 1069 1070 1071 1072 1073 1074
	int (*conf_tx)(struct ieee80211_hw *hw, int queue,
		       const struct ieee80211_tx_queue_params *params);
	int (*get_tx_stats)(struct ieee80211_hw *hw,
			    struct ieee80211_tx_queue_stats *stats);
	u64 (*get_tsf)(struct ieee80211_hw *hw);
	void (*reset_tsf)(struct ieee80211_hw *hw);
	int (*beacon_update)(struct ieee80211_hw *hw,
			     struct sk_buff *skb,
			     struct ieee80211_tx_control *control);
	int (*tx_last_beacon)(struct ieee80211_hw *hw);
1075
	int (*conf_ht)(struct ieee80211_hw *hw, struct ieee80211_conf *conf);
1076 1077
	int (*ampdu_action)(struct ieee80211_hw *hw,
			    enum ieee80211_ampdu_mlme_action action,
1078
			    const u8 *addr, u16 tid, u16 *ssn);
1079 1080
};

1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091
/**
 * ieee80211_alloc_hw -  Allocate a new hardware device
 *
 * This must be called once for each hardware device. The returned pointer
 * must be used to refer to this device when calling other functions.
 * mac80211 allocates a private data area for the driver pointed to by
 * @priv in &struct ieee80211_hw, the size of this area is given as
 * @priv_data_len.
 *
 * @priv_data_len: length of private data
 * @ops: callbacks for this device
1092 1093 1094 1095
 */
struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len,
					const struct ieee80211_ops *ops);

1096 1097 1098
/**
 * ieee80211_register_hw - Register hardware device
 *
J
Johannes Berg 已提交
1099 1100 1101
 * You must call this function before any other functions in
 * mac80211. Note that before a hardware can be registered, you
 * need to fill the contained wiphy's information.
1102 1103 1104
 *
 * @hw: the device to register as returned by ieee80211_alloc_hw()
 */
1105 1106 1107 1108 1109
int ieee80211_register_hw(struct ieee80211_hw *hw);

#ifdef CONFIG_MAC80211_LEDS
extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
1110
extern char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw);
I
Ivo van Doorn 已提交
1111
extern char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw);
1112
#endif
1113 1114 1115 1116 1117 1118 1119 1120 1121 1122
/**
 * ieee80211_get_tx_led_name - get name of TX LED
 *
 * mac80211 creates a transmit LED trigger for each wireless hardware
 * that can be used to drive LEDs if your driver registers a LED device.
 * This function returns the name (or %NULL if not configured for LEDs)
 * of the trigger so you can automatically link the LED device.
 *
 * @hw: the hardware to get the LED trigger name for
 */
1123 1124 1125 1126 1127 1128 1129 1130 1131
static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw)
{
#ifdef CONFIG_MAC80211_LEDS
	return __ieee80211_get_tx_led_name(hw);
#else
	return NULL;
#endif
}

1132 1133 1134 1135 1136 1137 1138 1139 1140 1141
/**
 * ieee80211_get_rx_led_name - get name of RX LED
 *
 * mac80211 creates a receive LED trigger for each wireless hardware
 * that can be used to drive LEDs if your driver registers a LED device.
 * This function returns the name (or %NULL if not configured for LEDs)
 * of the trigger so you can automatically link the LED device.
 *
 * @hw: the hardware to get the LED trigger name for
 */
1142 1143 1144 1145 1146 1147 1148 1149 1150
static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw)
{
#ifdef CONFIG_MAC80211_LEDS
	return __ieee80211_get_rx_led_name(hw);
#else
	return NULL;
#endif
}

I
Ivo van Doorn 已提交
1151 1152 1153 1154 1155 1156 1157 1158 1159 1160
/**
 * ieee80211_get_assoc_led_name - get name of association LED
 *
 * mac80211 creates a association LED trigger for each wireless hardware
 * that can be used to drive LEDs if your driver registers a LED device.
 * This function returns the name (or %NULL if not configured for LEDs)
 * of the trigger so you can automatically link the LED device.
 *
 * @hw: the hardware to get the LED trigger name for
 */
1161 1162 1163 1164 1165 1166 1167 1168 1169
static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw)
{
#ifdef CONFIG_MAC80211_LEDS
	return __ieee80211_get_assoc_led_name(hw);
#else
	return NULL;
#endif
}

I
Ivo van Doorn 已提交
1170 1171 1172 1173 1174 1175 1176 1177 1178 1179 1180 1181 1182 1183 1184 1185 1186 1187
/**
 * ieee80211_get_radio_led_name - get name of radio LED
 *
 * mac80211 creates a radio change LED trigger for each wireless hardware
 * that can be used to drive LEDs if your driver registers a LED device.
 * This function returns the name (or %NULL if not configured for LEDs)
 * of the trigger so you can automatically link the LED device.
 *
 * @hw: the hardware to get the LED trigger name for
 */
static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw)
{
#ifdef CONFIG_MAC80211_LEDS
	return __ieee80211_get_radio_led_name(hw);
#else
	return NULL;
#endif
}
1188

1189 1190 1191 1192 1193 1194 1195 1196
/**
 * ieee80211_unregister_hw - Unregister a hardware device
 *
 * This function instructs mac80211 to free allocated resources
 * and unregister netdevices from the networking subsystem.
 *
 * @hw: the hardware to unregister
 */
1197 1198
void ieee80211_unregister_hw(struct ieee80211_hw *hw);

1199 1200 1201 1202 1203 1204 1205 1206 1207
/**
 * ieee80211_free_hw - free hardware descriptor
 *
 * This function frees everything that was allocated, including the
 * private data for the driver. You must call ieee80211_unregister_hw()
 * before calling this function
 *
 * @hw: the hardware to free
 */
1208 1209
void ieee80211_free_hw(struct ieee80211_hw *hw);

1210
/* trick to avoid symbol clashes with the ieee80211 subsystem */
1211 1212
void __ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb,
		    struct ieee80211_rx_status *status);
1213 1214 1215 1216 1217 1218 1219 1220

/**
 * ieee80211_rx - receive frame
 *
 * Use this function to hand received frames to mac80211. The receive
 * buffer in @skb must start with an IEEE 802.11 header or a radiotap
 * header if %RX_FLAG_RADIOTAP is set in the @status flags.
 *
1221 1222 1223 1224
 * This function may not be called in IRQ context. Calls to this function
 * for a single hardware must be synchronized against each other. Calls
 * to this function and ieee80211_rx_irqsafe() may not be mixed for a
 * single hardware.
1225 1226 1227 1228 1229 1230 1231 1232 1233 1234 1235 1236 1237 1238 1239 1240
 *
 * @hw: the hardware this frame came in on
 * @skb: the buffer to receive, owned by mac80211 after this call
 * @status: status of this frame; the status pointer need not be valid
 *	after this function returns
 */
static inline void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb,
				struct ieee80211_rx_status *status)
{
	__ieee80211_rx(hw, skb, status);
}

/**
 * ieee80211_rx_irqsafe - receive frame
 *
 * Like ieee80211_rx() but can be called in IRQ context
1241 1242 1243 1244
 * (internally defers to a tasklet.)
 *
 * Calls to this function and ieee80211_rx() may not be mixed for a
 * single hardware.
1245 1246 1247 1248 1249 1250 1251
 *
 * @hw: the hardware this frame came in on
 * @skb: the buffer to receive, owned by mac80211 after this call
 * @status: status of this frame; the status pointer need not be valid
 *	after this function returns and is not freed by mac80211,
 *	it is recommended that it points to a stack area
 */
1252 1253 1254 1255
void ieee80211_rx_irqsafe(struct ieee80211_hw *hw,
			  struct sk_buff *skb,
			  struct ieee80211_rx_status *status);

1256 1257 1258 1259 1260 1261 1262
/**
 * ieee80211_tx_status - transmit status callback
 *
 * Call this function for all transmitted frames after they have been
 * transmitted. It is permissible to not call this function for
 * multicast frames but this can affect statistics.
 *
1263 1264 1265 1266 1267
 * This function may not be called in IRQ context. Calls to this function
 * for a single hardware must be synchronized against each other. Calls
 * to this function and ieee80211_tx_status_irqsafe() may not be mixed
 * for a single hardware.
 *
1268 1269 1270 1271 1272 1273
 * @hw: the hardware the frame was transmitted by
 * @skb: the frame that was transmitted, owned by mac80211 after this call
 * @status: status information for this frame; the status pointer need not
 *	be valid after this function returns and is not freed by mac80211,
 *	it is recommended that it points to a stack area
 */
1274 1275 1276
void ieee80211_tx_status(struct ieee80211_hw *hw,
			 struct sk_buff *skb,
			 struct ieee80211_tx_status *status);
1277 1278 1279 1280 1281 1282 1283 1284 1285 1286 1287 1288 1289 1290 1291 1292

/**
 * ieee80211_tx_status_irqsafe - irq-safe transmit status callback
 *
 * Like ieee80211_tx_status() but can be called in IRQ context
 * (internally defers to a tasklet.)
 *
 * Calls to this function and ieee80211_tx_status() may not be mixed for a
 * single hardware.
 *
 * @hw: the hardware the frame was transmitted by
 * @skb: the frame that was transmitted, owned by mac80211 after this call
 * @status: status information for this frame; the status pointer need not
 *	be valid after this function returns and is not freed by mac80211,
 *	it is recommended that it points to a stack area
 */
1293 1294 1295 1296 1297 1298 1299
void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
				 struct sk_buff *skb,
				 struct ieee80211_tx_status *status);

/**
 * ieee80211_beacon_get - beacon generation function
 * @hw: pointer obtained from ieee80211_alloc_hw().
1300
 * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
1301 1302 1303 1304 1305 1306 1307 1308 1309 1310
 * @control: will be filled with information needed to send this beacon.
 *
 * If the beacon frames are generated by the host system (i.e., not in
 * hardware/firmware), the low-level driver uses this function to receive
 * the next beacon frame from the 802.11 code. The low-level is responsible
 * for calling this function before beacon data is needed (e.g., based on
 * hardware interrupt). Returned skb is used only once and low-level driver
 * is responsible of freeing it.
 */
struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
1311
				     struct ieee80211_vif *vif,
1312 1313 1314 1315 1316
				     struct ieee80211_tx_control *control);

/**
 * ieee80211_rts_get - RTS frame generation function
 * @hw: pointer obtained from ieee80211_alloc_hw().
1317
 * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
1318 1319 1320 1321 1322 1323 1324 1325 1326 1327
 * @frame: pointer to the frame that is going to be protected by the RTS.
 * @frame_len: the frame length (in octets).
 * @frame_txctl: &struct ieee80211_tx_control of the frame.
 * @rts: The buffer where to store the RTS frame.
 *
 * If the RTS frames are generated by the host system (i.e., not in
 * hardware/firmware), the low-level driver uses this function to receive
 * the next RTS frame from the 802.11 code. The low-level is responsible
 * for calling this function before and RTS frame is needed.
 */
1328
void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
1329 1330 1331 1332 1333 1334 1335
		       const void *frame, size_t frame_len,
		       const struct ieee80211_tx_control *frame_txctl,
		       struct ieee80211_rts *rts);

/**
 * ieee80211_rts_duration - Get the duration field for an RTS frame
 * @hw: pointer obtained from ieee80211_alloc_hw().
1336
 * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
1337 1338 1339 1340 1341 1342 1343
 * @frame_len: the length of the frame that is going to be protected by the RTS.
 * @frame_txctl: &struct ieee80211_tx_control of the frame.
 *
 * If the RTS is generated in firmware, but the host system must provide
 * the duration field, the low-level driver uses this function to receive
 * the duration field value in little-endian byteorder.
 */
1344 1345
__le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
			      struct ieee80211_vif *vif, size_t frame_len,
1346 1347 1348 1349 1350
			      const struct ieee80211_tx_control *frame_txctl);

/**
 * ieee80211_ctstoself_get - CTS-to-self frame generation function
 * @hw: pointer obtained from ieee80211_alloc_hw().
1351
 * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
1352 1353 1354 1355 1356 1357 1358 1359 1360 1361
 * @frame: pointer to the frame that is going to be protected by the CTS-to-self.
 * @frame_len: the frame length (in octets).
 * @frame_txctl: &struct ieee80211_tx_control of the frame.
 * @cts: The buffer where to store the CTS-to-self frame.
 *
 * If the CTS-to-self frames are generated by the host system (i.e., not in
 * hardware/firmware), the low-level driver uses this function to receive
 * the next CTS-to-self frame from the 802.11 code. The low-level is responsible
 * for calling this function before and CTS-to-self frame is needed.
 */
1362 1363
void ieee80211_ctstoself_get(struct ieee80211_hw *hw,
			     struct ieee80211_vif *vif,
1364 1365 1366 1367 1368 1369 1370
			     const void *frame, size_t frame_len,
			     const struct ieee80211_tx_control *frame_txctl,
			     struct ieee80211_cts *cts);

/**
 * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame
 * @hw: pointer obtained from ieee80211_alloc_hw().
1371
 * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
1372 1373 1374 1375 1376 1377 1378
 * @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
 * @frame_txctl: &struct ieee80211_tx_control of the frame.
 *
 * If the CTS-to-self is generated in firmware, but the host system must provide
 * the duration field, the low-level driver uses this function to receive
 * the duration field value in little-endian byteorder.
 */
1379 1380
__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
				    struct ieee80211_vif *vif,
1381 1382 1383 1384 1385 1386
				    size_t frame_len,
				    const struct ieee80211_tx_control *frame_txctl);

/**
 * ieee80211_generic_frame_duration - Calculate the duration field for a frame
 * @hw: pointer obtained from ieee80211_alloc_hw().
1387
 * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
1388
 * @frame_len: the length of the frame.
1389
 * @rate: the rate at which the frame is going to be transmitted.
1390 1391 1392 1393
 *
 * Calculate the duration field of some generic frame, given its
 * length and transmission rate (in 100kbps).
 */
1394 1395
__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
					struct ieee80211_vif *vif,
1396
					size_t frame_len,
1397
					struct ieee80211_rate *rate);
1398 1399 1400 1401

/**
 * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
 * @hw: pointer as obtained from ieee80211_alloc_hw().
1402
 * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
1403 1404 1405 1406 1407 1408 1409 1410 1411 1412 1413 1414 1415 1416 1417 1418 1419 1420
 * @control: will be filled with information needed to send returned frame.
 *
 * Function for accessing buffered broadcast and multicast frames. If
 * hardware/firmware does not implement buffering of broadcast/multicast
 * frames when power saving is used, 802.11 code buffers them in the host
 * memory. The low-level driver uses this function to fetch next buffered
 * frame. In most cases, this is used when generating beacon frame. This
 * function returns a pointer to the next buffered skb or NULL if no more
 * buffered frames are available.
 *
 * Note: buffered frames are returned only after DTIM beacon frame was
 * generated with ieee80211_beacon_get() and the low-level driver must thus
 * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns
 * NULL if the previous generated beacon was not DTIM, so the low-level driver
 * does not need to check for DTIM beacons separately and should be able to
 * use common code for all beacons.
 */
struct sk_buff *
1421
ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
1422 1423
			  struct ieee80211_tx_control *control);

1424 1425 1426 1427
/**
 * ieee80211_get_hdrlen_from_skb - get header length from data
 *
 * Given an skb with a raw 802.11 header at the data pointer this function
1428 1429 1430
 * returns the 802.11 header length in bytes (not including encryption
 * headers). If the data in the sk_buff is too short to contain a valid 802.11
 * header the function returns 0.
1431 1432
 *
 * @skb: the frame
1433 1434 1435
 */
int ieee80211_get_hdrlen_from_skb(const struct sk_buff *skb);

1436 1437 1438 1439 1440 1441 1442 1443
/**
 * ieee80211_get_hdrlen - get header length from frame control
 *
 * This function returns the 802.11 header length in bytes (not including
 * encryption headers.)
 *
 * @fc: the frame control field (in CPU endianness)
 */
1444 1445 1446 1447 1448 1449 1450 1451 1452 1453 1454 1455 1456 1457 1458 1459 1460 1461 1462 1463 1464 1465 1466 1467 1468 1469 1470 1471 1472 1473 1474 1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485 1486 1487
int ieee80211_get_hdrlen(u16 fc);

/**
 * ieee80211_wake_queue - wake specific queue
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 * @queue: queue number (counted from zero).
 *
 * Drivers should use this function instead of netif_wake_queue.
 */
void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue);

/**
 * ieee80211_stop_queue - stop specific queue
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 * @queue: queue number (counted from zero).
 *
 * Drivers should use this function instead of netif_stop_queue.
 */
void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue);

/**
 * ieee80211_start_queues - start all queues
 * @hw: pointer to as obtained from ieee80211_alloc_hw().
 *
 * Drivers should use this function instead of netif_start_queue.
 */
void ieee80211_start_queues(struct ieee80211_hw *hw);

/**
 * ieee80211_stop_queues - stop all queues
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 *
 * Drivers should use this function instead of netif_stop_queue.
 */
void ieee80211_stop_queues(struct ieee80211_hw *hw);

/**
 * ieee80211_wake_queues - wake all queues
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 *
 * Drivers should use this function instead of netif_wake_queue.
 */
void ieee80211_wake_queues(struct ieee80211_hw *hw);

1488 1489 1490 1491 1492 1493 1494 1495 1496
/**
 * ieee80211_scan_completed - completed hardware scan
 *
 * When hardware scan offload is used (i.e. the hw_scan() callback is
 * assigned) this function needs to be called by the driver to notify
 * mac80211 that the scan finished.
 *
 * @hw: the hardware that finished the scan
 */
1497 1498
void ieee80211_scan_completed(struct ieee80211_hw *hw);

1499 1500 1501 1502 1503 1504 1505
/**
 * ieee80211_iterate_active_interfaces - iterate active interfaces
 *
 * This function iterates over the interfaces associated with a given
 * hardware that are currently active and calls the callback for them.
 *
 * @hw: the hardware struct of which the interfaces should be iterated over
1506
 * @iterator: the iterator function to call, cannot sleep
1507 1508 1509 1510
 * @data: first argument of the iterator function
 */
void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw,
					 void (*iterator)(void *data, u8 *mac,
1511
						struct ieee80211_vif *vif),
1512 1513
					 void *data);

1514 1515 1516 1517 1518 1519 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538 1539 1540 1541 1542 1543 1544 1545 1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561 1562 1563 1564 1565 1566 1567 1568 1569 1570 1571 1572 1573 1574 1575 1576 1577 1578 1579 1580 1581 1582 1583 1584 1585 1586 1587 1588 1589 1590
/**
 * ieee80211_start_tx_ba_session - Start a tx Block Ack session.
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 * @ra: receiver address of the BA session recipient
 * @tid: the TID to BA on.
 * @return: success if addBA request was sent, failure otherwise
 *
 * Although mac80211/low level driver/user space application can estimate
 * the need to start aggregation on a certain RA/TID, the session level
 * will be managed by the mac80211.
 */
int ieee80211_start_tx_ba_session(struct ieee80211_hw *hw, u8 *ra, u16 tid);

/**
 * ieee80211_start_tx_ba_cb - low level driver ready to aggregate.
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 * @ra: receiver address of the BA session recipient.
 * @tid: the TID to BA on.
 *
 * This function must be called by low level driver once it has
 * finished with preparations for the BA session.
 */
void ieee80211_start_tx_ba_cb(struct ieee80211_hw *hw, u8 *ra, u16 tid);

/**
 * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate.
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 * @ra: receiver address of the BA session recipient.
 * @tid: the TID to BA on.
 *
 * This function must be called by low level driver once it has
 * finished with preparations for the BA session.
 * This version of the function is irq safe.
 */
void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra,
				      u16 tid);

/**
 * ieee80211_stop_tx_ba_session - Stop a Block Ack session.
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 * @ra: receiver address of the BA session recipient
 * @tid: the TID to stop BA.
 * @initiator: if indicates initiator DELBA frame will be sent.
 * @return: error if no sta with matching da found, success otherwise
 *
 * Although mac80211/low level driver/user space application can estimate
 * the need to stop aggregation on a certain RA/TID, the session level
 * will be managed by the mac80211.
 */
int ieee80211_stop_tx_ba_session(struct ieee80211_hw *hw,
				 u8 *ra, u16 tid,
				 enum ieee80211_back_parties initiator);

/**
 * ieee80211_stop_tx_ba_cb - low level driver ready to stop aggregate.
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 * @ra: receiver address of the BA session recipient.
 * @tid: the desired TID to BA on.
 *
 * This function must be called by low level driver once it has
 * finished with preparations for the BA session tear down.
 */
void ieee80211_stop_tx_ba_cb(struct ieee80211_hw *hw, u8 *ra, u8 tid);

/**
 * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate.
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 * @ra: receiver address of the BA session recipient.
 * @tid: the desired TID to BA on.
 *
 * This function must be called by low level driver once it has
 * finished with preparations for the BA session tear down.
 * This version of the function is irq safe.
 */
void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra,
				     u16 tid);

1591
#endif /* MAC80211_H */