Kconfig

menu "Hardware Drivers Config"

config SOC_SERIES_GD32F20x
    bool
    default y

config SOC_GD32205R
    bool
    select SOC_SERIES_GD32F20x
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y
	
menu "Onboard Peripheral Drivers"

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART0
                bool "Enable UART0"
                default n

            config BSP_UART0_RX_USING_DMA
                bool "Enable UART0 RX DMA"
                depends on BSP_USING_UART0 
                select RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART1
                bool "Enable UART1"
                default y

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 
                select RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART2
                bool "Enable UART2"
                default n

            config BSP_UART2_RX_USING_DMA
                bool "Enable UART2 RX DMA"
                depends on BSP_USING_UART2 
                select RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART3
                bool "Enable UART3"
                default n

            config BSP_UART3_RX_USING_DMA
                bool "Enable UART3 RX DMA"
                depends on BSP_USING_UART3 
                select RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART4
                bool "Enable UART4"
                default n

            config BSP_UART4_RX_USING_DMA
                bool "Enable UART4 RX DMA"
                depends on BSP_USING_UART4 
                select RT_SERIAL_USING_DMA
                default n
        endif

    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1 BUS"
                default n

            config BSP_SPI1_TX_USING_DMA
                bool "Enable SPI1 TX DMA"
                depends on BSP_USING_SPI1
                default n
                
            config BSP_SPI1_RX_USING_DMA
                bool "Enable SPI1 RX DMA"
                depends on BSP_USING_SPI1
                select BSP_SPI1_TX_USING_DMA
                default n
        endif

    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            config BSP_I2C1_SCL_PIN
                int "i2c1 scl pin number"
                range 1 216
                default 24
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 1 216
                default 25
        endif
    source "../libraries/gd32_drivers/Kconfig"
    
endmenu

menu "Board extended module Drivers"

endmenu
 
endmenu