- 18 9月, 2018 17 次提交
-
-
由 david-cermak 提交于
* rmt driver initial version * supporting conti mode plus interrupts * using conitnous mode for sending more data * working continous mode * rmt driver cleanup after conti mode * initial version of rmt driver * adding a simple example * adding channel and block locks * modified of rmt interface for simpler/easier usage * adding header sentinels, split interface to common and additional settings * Fixes per code review + support for rx callback mode * renamed internal structures and enums, fixed formatting * cmake support for rmt * refactored tx-conti interrupts to function to make it more readable * added Tx and Rx examples * added license headers * minor updates per review * used struct access, renamed defines, corrected diagram
-
由 hreintke 提交于
* Initial * Implementation * Add to CMakelist.txt * Add example * Add IRAM_ATTR
-
由 hreintke 提交于
-
由 lbernstone 提交于
* First commit of FFat library * Fixed reboot loops if no fat present. Added CMakeLists * Functionalize the partition checks * Cleanup, especially in format * Dont format if mounted. More wording cleanup * 16M ffat should only be on 16M board * Fix some casting issues that trip up the compiler when building as ESP-IDF component
-
由 yelvlab 提交于
* Add BPI-BIT boards connfig * Add BPI-BIT v1.3 boards
-
由 Patrick Van Oosterwijck 提交于
* Add wESP32 support * Add default Ethernet config
-
由 Martin 提交于
Few testers let me know, they were unable with connection to Eduroam network under PEAP+MsCHAPv2 methods. They were trying many modifications. Solution is very absurd. Change board to STA mode manually. One tester from Italy was able to connect to Eduroam network under TTLS + MsCHAPv2 with that sketch too! Sketch was tested and worked almost for all testers with that problem.
-
由 Junxiao Shi 提交于
fixes #1734
-
由 lbernstone 提交于
* Add delay into example to allow print before sleep * Changed to Serial.flush()
-
由 Ifediora Elochukwu C 提交于
-
由 tobozo 提交于
see #1800
-
由 LynXzp 提交于
(removed quotes from last line, and fixed indentation, no text changes)
-
由 Baruch Nissenbaum 提交于
-
由 lewis he 提交于
-
由 Adam Coddington 提交于
Add functionality allowing rxBuffer of HardwareSerial to be changed in size via HardwareSerial::setRxBufferSize. (#1855)
-
由 Jose Carlos Garcia Diaz 提交于
-
由 lbernstone 提交于
* Updated ISSUE_TEMPLATE to try to get better postings * Added line for PSRAM enabled * More complete info request as per @stickbreaker
-
- 27 8月, 2018 1 次提交
-
-
由 copercini 提交于
- Delete queue at end - Close BT connection before end - DeInit SPP
-
- 18 8月, 2018 5 次提交
-
-
由 me-no-dev 提交于
-
由 me-no-dev 提交于
-
由 chuck todd 提交于
The original pins_arduino.h did not correspond to the actual hardware.
-
由 chuck todd 提交于
If the esp32 is reset during a i2c read cycle the slave device may be in control of the SDA line. If the SDA line is held low, the esp32 cannot issue a START or STOP to recover the bus. The previous code did not correctly configure the SCL output pin, and it cycled SCL 9 times with SDA Low. Since the slave device was in a READ cycle, it just continued outputting the bits of the current byte. When the ACK/NAK bit space occurred, The low output value of SDA was interpreted as ACK so the slave device continued with the next byte. It never terminated the READ cycle. This new code will correctly recover from an interrupted READ
-
由 Eric 提交于
add a troubleshooting hint
-
- 16 8月, 2018 1 次提交
-
-
- 14 8月, 2018 5 次提交
-
-
由 Ivan Kravets 提交于
-
由 Martin 提交于
* informations about sketch * Update README.md
-
由 Tokusei Noborio 提交于
-
由 lbernstone 提交于
-
由 chuck todd 提交于
* ReSTART fix, Sequencing fix pr #1665 introduce a problem with ReSTART, when solving this problem I found an interaction between the TxFifo refill, RxFifo empty and CMD[] fill. during certain sequences a dataqueue command would be skipped, this skipping resulted in a mismatch between the contents of the TxFifo and the i2c command sequence. The problem manifested as an ACK error. In addition to this required bug fix I propose: * `Wire.begin()` be changed from a `void` to a `bool` this will allow the reset functionality of `Wire.begin()` to be reported. Currently `Wire.begin()` attempts to reset the i2c Peripheral, but cannot report success/failure. * `Wire.busy()` be added. this `bool` function returns the hardware status of the bus. This status can be use in multi-master environments for application level interleaving of commands, also in single master environment, it can be used to detect a 'hung' bus. With the functional change to `Wire.begin()` this allows app level recover of a hung bus. * `Wire.lastError()` value updated for all errors, previously when interleaving `Wire.endTransmission(false)` and `Wire.readTransmission(false)`, the 128 byte `Wire.write()` buffer was exhausted without generating and error(very exotic). I discovered this error when I created a sequence of directed reads to a EEPROM. Each directed read used 2 bytes of the 128 byte `write()` buffer, so after 64 consecutive ReSTART writes with ReSTART reads, `Wire()` had no room to record the directed address bytes. It generated just a NAK check without setting the EEPROMs internal register address. The succeeding ReSTART read succeeded at incorrect address. * Changes to the HAL layer: ** added `i2cGetStatus()` which returns the i2c peripheral status word, used to detect bus_busy currently ** added `i2cDebug()` programmatic control of debug buffer output ** changed `i2cAddQueue()` to allow data_only queue element this will allow a i2c transaction to use multiple data pointers. ** removed direct access to DumpInts(), DumpI2c() from app, use i2cDebug() to set trigger points * * Update esp32-hal-i2c.c * Update Wire.cpp * ReSTART, Sequencing pr #1665 introduce a problem with ReSTART, when solving this problem I found an interaction between the TxFifo refill, RxFifo empty and CMD[] fill. during certain sequences a dataqueue command would be skipped, this skipping resulted in a mismatch between the contents of the TxFifo and the i2c command sequence. The problem manifested as an ACK error. In addition to this required bug fix I propose: * `Wire.begin()` be changed from a `void` to a `bool` this will allow the reset functionality of `Wire.begin()` to be reported. Currently `Wire.begin()` attempts to reset the i2c Peripheral, but cannot report success/failure. * `Wire.busy()` be added. this `bool` function returns the hardware status of the bus. This status can be use in multi-master environments for application level interleaving of commands, also in single master environment, it can be used to detect a 'hung' bus. With the functional change to `Wire.begin()` this allows app level recover of a hung bus. * `Wire.lastError()` value updated for all errors, previously when interleaving `Wire.endTransmission(false)` and `Wire.readTransmission(false)`, the 128 byte `Wire.write()` buffer was exhausted without generating and error(very exotic). I discovered this error when I created a sequence of directed reads to a EEPROM. Each directed read used 2 bytes of the 128 byte `write()` buffer, so after 64 consecutive ReSTART writes with ReSTART reads, `Wire()` had no room to record the directed address bytes. It generated just a NAK check without setting the EEPROMs internal register address. The succeeding ReSTART read succeeded at incorrect address. * Changes to the HAL layer: ** added `i2cGetStatus()` which returns the i2c peripheral status word, used to detect bus_busy currently ** added `i2cDebug()` programmatic control of debug buffer output ** changed `i2cAddQueue()` to allow data_only queue element this will allow a i2c transaction to use multiple data pointers. ** removed direct access to DumpInts(), DumpI2c() from app, use i2cDebug() to set trigger points * * Forgot DebugFlags Return @andriyadi found this, total brain fade on my part.
-
- 30 7月, 2018 4 次提交
-
-
由 copercini 提交于
-
由 Gei0r 提交于
Because TCP is stream-based, an earlier read can 'take away' the "OK" response from the device, so that a later read doesn't get the message.
-
由 lbernstone 提交于
* Added instructions for installation with boards manager (stolen directly from esp8266) * changed to production link instead of dev * Added to main README. Made mods to images as requested. * Added links for development package * Moved version images to README.md * Just a little change for cleaner look * Cleaned up README.md and boards_manager.md to make installation easier.
-
由 copercini 提交于
-
- 28 7月, 2018 2 次提交
-
-
由 pacucha42 提交于
-
由 WEMOS Electronics 提交于
-
- 26 7月, 2018 4 次提交
-
-
由 lbernstone 提交于
* Added instructions for installation with boards manager (stolen directly from esp8266) * changed to production link instead of dev * Added to main README. Made mods to images as requested. * Added links for development package
-
由 me-no-dev 提交于
-
由 me-no-dev 提交于
-
由 lbernstone 提交于
* Added a define to format the spiffs in SPIFFS_Test.ino * Uncommented the define * Matched define names
-
- 25 7月, 2018 1 次提交
-
-
由 MaValki 提交于
speed up uploading data. Now there is no need to call time consuming client.connected() method.
-