fix some format issues;

bsp/stm32/stm32f410-st-nucleo/README.md

@@ -20,7 +20,7 @@
 
 ![board](figures/board.png)
 
-该开发板常用 ** 板载资源 ** 如下：
+该开发板常用 **板载资源** 如下：
 
 - MCU：STM32F410RBT6，主频 84MHz，128KB FLASH ，32KB RAM。
 - 常用外设
@@ -91,7 +91,7 @@ msh >
 
 4. 输入 `scons --target=mdk4/mdk5/iar` 命令重新生成工程。
 
-本章节更多详细的介绍请参考 [STM32 系列 BSP 外设驱动使用教程](../docs/STM32 系列 BSP 外设驱动使用教程. md)。
+本章节更多详细的介绍请参考 [STM32 系列 BSP 外设驱动使用教程](../docs/STM32系列BSP外设驱动使用教程.md)。
 
 ## 注意事项
 

bsp/stm32/stm32f410-st-nucleo/board/Kconfig

@@ -42,95 +42,6 @@ menu "On-chip Peripheral Drivers"
                 default n
 
         endif
-
-    menuconfig BSP_USING_I2C1
-        bool "Enable I2C1 BUS (software simulation)"
-        default n
-        select RT_USING_I2C
-        select RT_USING_I2C_BITOPS
-        select RT_USING_PIN
-        if BSP_USING_I2C1
-            comment "Notice: PB8 --> 24; PB9 --> 25" 
-            config BSP_I2C1_SCL_PIN
-                int "i2c1 scl pin number"
-                range 0 80
-                default 24
-            config BSP_I2C1_SDA_PIN
-                int "I2C1 sda pin number"
-                range 0 80
-                default 25
-        endif
-
-    menuconfig BSP_USING_SPI
-        bool "Enable SPI BUS"
-        default n
-        select RT_USING_SPI
-        if BSP_USING_SPI
-            config BSP_USING_SPI1
-                bool "Enable SPI1 BUS"
-                default n
-
-            config BSP_SPI1_TX_USING_DMA
-                bool "Enable SPI1 TX DMA"
-                depends on BSP_USING_SPI1
-                default n
-                
-            config BSP_SPI1_RX_USING_DMA
-                bool "Enable SPI1 RX DMA"
-                depends on BSP_USING_SPI1
-                select BSP_SPI1_TX_USING_DMA
-                default n
-        endif
-
-    menuconfig BSP_USING_PWM
-        bool "Enable pwm"
-        default n
-        select RT_USING_PWM
-        if BSP_USING_PWM
-        menuconfig BSP_USING_PWM3
-            bool "Enable timer3 output pwm"
-            default n
-            if BSP_USING_PWM3
-                config BSP_USING_PWM3_CH1
-                    bool "Enable PWM3 channel1 (PA6)"
-                    default n
-
-                config BSP_USING_PWM3_CH2
-                    bool "Enable PWM3 channel2 (PA7)"
-                    default n
-
-                config BSP_USING_PWM3_CH3
-                    bool "Enable PWM3 channel3 (PB0)"
-                    default n
-
-                config BSP_USING_PWM3_CH4
-                    bool "Enable PWM3 channel4 (PB1)"
-                    default n
-            endif
-        endif
-
-    menuconfig BSP_USING_ONCHIP_RTC
-        bool "Enable RTC"
-        select RT_USING_RTC
-        select RT_USING_LIBC
-        default n
-        if BSP_USING_ONCHIP_RTC
-            choice
-                prompt "Select clock source"
-                default BSP_RTC_USING_LSE
-
-                config BSP_RTC_USING_LSE
-                    bool "RTC USING LSE"
-
-                config BSP_RTC_USING_LSI
-                    bool "RTC USING LSI"
-            endchoice
-        endif
-
-    config BSP_USING_ON_CHIP_FLASH
-        bool "Enable on-chip FLASH"
-        default n
-    source "../libraries/HAL_Drivers/Kconfig"
     
 endmenu
 

bsp/stm32/stm32f410-st-nucleo/board/SConscript

@@ -34,4 +34,4 @@ elif rtconfig.CROSS_TOOL == 'iar':
 CPPDEFINES = ['STM32F410Rx']
 group = DefineGroup('Drivers', src, depend = [''], CPPPATH = path, CPPDEFINES = CPPDEFINES)
 
-Return('group')
\ No newline at end of file
+Return('group')

bsp/stm32/stm32f410-st-nucleo/board/board.c

@@ -5,7 +5,7 @@
  *
  * Change Logs:
  * Date           Author       Notes
- * 2020-03-07     tanglj86   first version
+ * 2020-03-07     tanglj86     first version
  */
 
 #include "board.h"

bsp/stm32/stm32f410-st-nucleo/board/board.h

@@ -5,7 +5,7 @@
  *
  * Change Logs:
  * Date           Author       Notes
- * 2020-03-07     tanglj86   first version
+ * 2020-03-07     tanglj86     first version
  */
 
 #ifndef __BOARD_H__