- 06 4月, 2020 1 次提交
-
-
由 AmadeusGhost 提交于
* ramips: increase HiWiFi HC5962 kernel partition to 4M Increase kernel partition because 2M is insufficient for 4.19 Because the partition changes, previous version of OpenWrt cannot upgrade to this version Signed-off-by: NDENG Qingfang <dengqf6@mail2.sysu.edu.cn> * ramips: use all reserved space for HiWiFi HC5962 Idea was from ad6c6361f9f8 ("ath79: enable all space on Netgear ar9344-based WNDR routers") These stock partitons: "backup", "hw_panic", "overly", firmware_backup", "opt" do not contain any device-specific data and can be used for /overlay, resulting in 121M space Users should erase those partitions with command `mtd erase <partition name>` prior to upgrading to this version Signed-off-by: NDENG Qingfang <dengqf6@mail2.sysu.edu.cn> Co-authored-by: NDENG Qingfang <dengqf6@mail2.sysu.edu.cn>
-
- 15 3月, 2020 1 次提交
-
-
由 AmadeusGhost 提交于
-
- 22 2月, 2020 2 次提交
-
-
由 AmadeusGhost 提交于
This commit sync ramips source code from openwrt master. 1. ramips: gsw_mt7621: disable PORT 5 MAC RX/TX flow control by default 2. ramips: allow to set switchdev by board in ramips_set_preinit_iface 3. kernel: fix typos in KernelPackage description
-
由 LGA1150 提交于
* generic: support mtd-mac-address-ascii It supports formats of both 001122334455 and 00:11:22:33:44:55 Signed-off-by: NYousong Zhou <yszhou4tech@gmail.com> * ramips: add JDCloud Co-authored-by: NYousong Zhou <yszhou4tech@gmail.com>
-
- 08 2月, 2020 1 次提交
-
-
由 AmadeusGhost 提交于
This may affect wireless and network.
-
- 05 2月, 2020 1 次提交
-
-
由 AmadeusGhost 提交于
This commit sync ramips from openwrt master, and revert use caldata.sh so that wireless for some devices can works.
-
- 15 12月, 2019 2 次提交
- 14 12月, 2019 1 次提交
-
-
由 LEAN-ESX 提交于
-
- 11 12月, 2019 1 次提交
-
-
由 AmadeusGhost 提交于
* ramips: XiaoYu-C5 fix to 512MB * Re-add support for XiaoYu-C5
-
- 08 12月, 2019 2 次提交
- 07 12月, 2019 1 次提交
-
-
由 LEAN-ESX 提交于
-
- 24 11月, 2019 1 次提交
-
-
由 LEAN-ESX 提交于
-
- 27 9月, 2019 1 次提交
-
-
由 LEAN-ESX 提交于
-
- 12 9月, 2019 1 次提交
-
-
由 LEAN-ESX 提交于
-
- 14 8月, 2019 1 次提交
-
-
由 ITdesk01 提交于
SoC: MT7621AT RAM: 256MB Flash: 16M SPI Ethernet: 5x GE ports WiFi: 2.4G: MT7615N 5G: MT7615N Flash instruction: 1.Modify the file to linux.bin 2.Set up FTP service 3.Computer settings fixed IP: 192.168.179.50 255.255.255.0 4.Turn on the power and press and hold the reset button until the indicator light is on for about 5 seconds. Signed-off-by: NZhenjian Zhang <itdesk.zhang@gmail.com>
-
- 26 7月, 2019 1 次提交
-
-
由 LEAN-ESX 提交于
-
- 03 5月, 2019 1 次提交
-
-
由 coolsnowwolf 提交于
-
- 01 5月, 2019 1 次提交
-
-
由 coolsnowwolf 提交于
-
- 20 4月, 2019 1 次提交
-
-
由 coolsnowwolf 提交于
-
- 15 4月, 2019 2 次提交
-
-
由 coolsnowwolf 提交于
This reverts commit 9cd0dc0d.
-
由 coolsnowwolf 提交于
-
- 20 2月, 2019 1 次提交
-
-
由 phorcys 提交于
Hardware is the same as mir3g except: ram 256M -> 128M switch lan 2 3 wan 1 -> lan 1 2 wan 4
-
- 08 1月, 2019 1 次提交
-
-
由 a1768623020 提交于
pbr-m1固件大小为32m
-
- 03 1月, 2019 1 次提交
-
-
- 28 12月, 2018 2 次提交
-
-
由 Fsick 提交于
-
由 coolsnowwolf 提交于
This reverts commit 506e55be.
-
- 27 12月, 2018 1 次提交
-
-
由 coolsnowwolf 提交于
-
- 28 11月, 2018 1 次提交
-
-
由 coolsnowwolf 提交于
-
- 21 10月, 2018 1 次提交
-
-
由 coolsnowwolf 提交于
-
- 18 10月, 2018 2 次提交
-
-
由 coolsnowwolf 提交于
-
由 coolsnowwolf 提交于
-
- 17 10月, 2018 1 次提交
-
-
由 coolsnowwolf 提交于
-
- 07 9月, 2018 1 次提交
-
-
由 coolsnowwolf 提交于
-
- 23 8月, 2018 1 次提交
-
-
由 coolsnowwolf 提交于
-
- 15 6月, 2018 1 次提交
-
-
由 coolsnowwolf 提交于
-
- 04 6月, 2018 1 次提交
-
-
由 coolsnowwolf 提交于
-
- 22 5月, 2018 1 次提交
-
-
由 coolsnowwolf 提交于
-
- 23 4月, 2018 1 次提交
-
-
由 coolsnowwolf 提交于
-