- 07 5月, 2017 1 次提交
-
-
由 Me No Dev 提交于
* Update IDF to 65acd99 * Update platformio and arduino build paths and libs * Update esptool binaries
-
- 06 5月, 2017 5 次提交
- 05 5月, 2017 3 次提交
-
-
由 WEMOS Electronics 提交于
* Add ESP.getChipId() function to get ESP32's ChipID. * change getChipId() to getEfuseMac()
-
由 Severin Smith 提交于
It appears that the configurations for `ck_out_edge` were inverted for `SPI_MODE2` and `SPI_MODE3`. You can check the technical reference manual on page 76, table 23 "Clock Polarity and Phase, and Corresponding SPI Register Values for SPI Master". I've check with my oscilloscope that the current configuration is wrong and this fix corrects the issue.
-
由 tzxespressio 提交于
-
- 28 4月, 2017 1 次提交
-
-
由 Martin Sloup 提交于
-
- 22 4月, 2017 4 次提交
-
-
由 Ahmed Talaat 提交于
fixing github url.
-
由 Me No Dev 提交于
-
由 me-no-dev 提交于
-
由 Me No Dev 提交于
Remove missing column so github can beautify the contents
-
- 13 4月, 2017 4 次提交
- 11 4月, 2017 1 次提交
-
-
由 Me No Dev 提交于
Fixes: https://github.com/espressif/arduino-esp32/issues/304 Thanks @jliegner :)
-
- 04 4月, 2017 7 次提交
- 31 3月, 2017 2 次提交
-
-
由 robin 提交于
-
由 copercini 提交于
* Support self signed certificates Fix for https://github.com/espressif/arduino-esp32/issues/265 mbedtls_ssl_conf_authmode was defined before mbedtls_ssl_config_defaults causing several bugs when no CA certificate is defined. * Implement Arduino's log facility Replace printf by ESP log handling * Remove \n from debug messages log_ doesn't need \n to break line.
-
- 26 3月, 2017 2 次提交
-
-
由 me-no-dev 提交于
Should Fix: https://github.com/espressif/arduino-esp32/issues/234
-
由 me-no-dev 提交于
Thanks @marcmerlin and @MartyMacGyver
-
- 24 3月, 2017 1 次提交
-
-
- 22 3月, 2017 1 次提交
-
-
由 me-no-dev 提交于
-
- 20 3月, 2017 5 次提交
-
-
-
-
由 copercini 提交于
Actually WiFiMulti is not working due some functions haven't equal comportment of ESP8266 Replace status == WL_DISCONNECTED => status != WL_CONNECTED Replace scanComplete() => scanNetworks() Maybe is more interesting, for keep the maximum compatibility, investigate why WL_DISCONNECTED and scanComplete() doesn't works in this case instead of just replace by this pull request.
-
由 me-no-dev 提交于
Closes: https://github.com/espressif/arduino-esp32/pull/267
-
由 me-no-dev 提交于
The card seems to need a bit of a nudge at boot to properly mount sometimes. Fixes: https://github.com/espressif/arduino-esp32/issues/272
-
- 19 3月, 2017 2 次提交
-
-
由 me-no-dev 提交于
-
- 14 3月, 2017 1 次提交
-
-
由 copercini 提交于
It's look more a practical guide "how to use SD lib"
-