Skip to content

R
rt-thread

人间散章 / rt-thread
与 Fork 源项目一致

Fork自 RT-Thread / rt-thread

通知 1
Star 1
Fork 0
R
rt-thread

体验新版 GitCode，发现更多精彩内容 >>

提交 d6ff0fc0 编写于 作者: W WangQiang
浏览文件
操作

增加了imxrt1064-nxp-evk的BSP的以太网功能

上级 13044b1e
隐藏空白更改
内联 并排
Showing with 1028 addition and 126 deletion
bsp/imxrt/imxrt1064-nxp-evk/applications/main.c
浏览文件 @ d6ff0fc0
......@@ -18,6 +18,7 @@
int main(void)
{
#ifndef PHY_USING_KSZ8081
/* set LED0 pin mode to output */
rt_pin_mode(LED0_PIN, PIN_MODE_OUTPUT);
......@@ -28,6 +29,7 @@ int main(void)
rt_pin_write(LED0_PIN, PIN_LOW);
rt_thread_mdelay(500);
}
#endif
}
void reboot(void)
......
bsp/imxrt/imxrt1064-nxp-evk/board/Kconfig
浏览文件 @ d6ff0fc0
......@@ -37,7 +37,28 @@ menu "On-chip Peripheral Drivers"
endmenu
menu "Onboard Peripheral Drivers"
config BSP_USING_SDRAM
bool "Enable SDRAM"
default n
menuconfig BSP_USING_ETH
bool "Enable Ethernet"
select PHY_USING_KSZ8081
select RT_USING_NETDEV
default n
if BSP_USING_ETH
config PHY_USING_KSZ8081
bool "i.MX RT1064EVK uses ksz8081 phy"
default y
config FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE
bool "Enable the PHY ksz8081 RMII50M mode"
depends on PHY_USING_KSZ8081
default y
endif
endmenu
menu "Board extended module Drivers"
......
bsp/imxrt/imxrt1064-nxp-evk/board/MCUX_Config/clock_config.c
浏览文件 @ d6ff0fc0
/*
* Copyright 2018 NXP
* All rights reserved.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
/*
* How to setup clock using clock driver functions:
*
......@@ -15,15 +22,15 @@
/* TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
!!GlobalInfo
product: Clocks v5.0
product: Clocks v4.1
processor: MIMXRT1064xxxxA
package_id: MIMXRT1064DVL6A
mcu_data: ksdk2_0
processor_version: 5.0.1
processor_version: 0.0.0
board: MIMXRT1064-EVK
* BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/
#include "clock_config.h"
#include "fsl_iomuxc.h"
/*******************************************************************************
* Definitions
......@@ -57,35 +64,23 @@ outputs:
- {id: CLK_1M.outFreq, value: 1 MHz}
- {id: CLK_24M.outFreq, value: 24 MHz}
- {id: CSI_CLK_ROOT.outFreq, value: 12 MHz}
- {id: ENET1_TX_CLK.outFreq, value: 2.4 MHz}
- {id: ENET2_125M_CLK.outFreq, value: 1.2 MHz}
- {id: ENET2_TX_CLK.outFreq, value: 1.2 MHz}
- {id: ENET_125M_CLK.outFreq, value: 2.4 MHz}
- {id: ENET_25M_REF_CLK.outFreq, value: 1.2 MHz}
- {id: FLEXIO1_CLK_ROOT.outFreq, value: 30 MHz}
- {id: FLEXIO2_CLK_ROOT.outFreq, value: 30 MHz}
- {id: FLEXSPI2_CLK_ROOT.outFreq, value: 264 MHz}
- {id: FLEXSPI2_CLK_ROOT.outFreq, value: 2880/11 MHz}
- {id: FLEXSPI_CLK_ROOT.outFreq, value: 2880/11 MHz}
- {id: GPT1_ipg_clk_highfreq.outFreq, value: 75 MHz}
- {id: GPT2_ipg_clk_highfreq.outFreq, value: 75 MHz}
- {id: IPG_CLK_ROOT.outFreq, value: 150 MHz}
- {id: LCDIF_CLK_ROOT.outFreq, value: 67.5/7 MHz}
- {id: LCDIF_CLK_ROOT.outFreq, value: 67.5 MHz}
- {id: LPI2C_CLK_ROOT.outFreq, value: 60 MHz}
- {id: LPSPI_CLK_ROOT.outFreq, value: 105.6 MHz}
- {id: LVDS1_CLK.outFreq, value: 1.2 GHz}
- {id: MQS_MCLK.outFreq, value: 1080/17 MHz}
- {id: PERCLK_CLK_ROOT.outFreq, value: 75 MHz}
- {id: PLL7_MAIN_CLK.outFreq, value: 24 MHz}
- {id: SAI1_CLK_ROOT.outFreq, value: 1080/17 MHz}
- {id: SAI1_MCLK1.outFreq, value: 1080/17 MHz}
- {id: SAI1_MCLK2.outFreq, value: 1080/17 MHz}
- {id: SAI1_MCLK3.outFreq, value: 30 MHz}
- {id: SAI2_CLK_ROOT.outFreq, value: 1080/17 MHz}
- {id: SAI2_MCLK1.outFreq, value: 1080/17 MHz}
- {id: SAI2_MCLK3.outFreq, value: 30 MHz}
- {id: SAI3_CLK_ROOT.outFreq, value: 1080/17 MHz}
- {id: SAI3_MCLK1.outFreq, value: 1080/17 MHz}
- {id: SAI3_MCLK3.outFreq, value: 30 MHz}
- {id: SEMC_CLK_ROOT.outFreq, value: 75 MHz}
- {id: SPDIF0_CLK_ROOT.outFreq, value: 30 MHz}
- {id: TRACE_CLK_ROOT.outFreq, value: 352/3 MHz}
......@@ -95,10 +90,10 @@ outputs:
settings:
- {id: CCM.AHB_PODF.scale, value: '1', locked: true}
- {id: CCM.ARM_PODF.scale, value: '2', locked: true}
- {id: CCM.FLEXSPI2_PODF.scale, value: '1', locked: true}
- {id: CCM.FLEXSPI2_SEL.sel, value: CCM_ANALOG.PLL3_PFD0_CLK}
- {id: CCM.FLEXSPI_PODF.scale, value: '1', locked: true}
- {id: CCM.FLEXSPI_SEL.sel, value: CCM_ANALOG.PLL3_PFD0_CLK}
- {id: CCM.LCDIF_PODF.scale, value: '8', locked: true}
- {id: CCM.LCDIF_PRED.scale, value: '7', locked: true}
- {id: CCM.LPSPI_PODF.scale, value: '5', locked: true}
- {id: CCM.PERCLK_PODF.scale, value: '2', locked: true}
- {id: CCM.SEMC_PODF.scale, value: '8'}
......@@ -107,6 +102,7 @@ settings:
- {id: CCM_ANALOG.PLL1_PREDIV.scale, value: '1', locked: true}
- {id: CCM_ANALOG.PLL1_VDIV.scale, value: '50', locked: true}
- {id: CCM_ANALOG.PLL2.denom, value: '1', locked: true}
- {id: CCM_ANALOG.PLL2.div, value: '22'}
- {id: CCM_ANALOG.PLL2.num, value: '0', locked: true}
- {id: CCM_ANALOG.PLL2_BYPASS.sel, value: CCM_ANALOG.PLL2_OUT_CLK}
- {id: CCM_ANALOG.PLL2_PFD0_BYPASS.sel, value: CCM_ANALOG.PLL2_PFD0}
......@@ -182,6 +178,77 @@ void BOARD_BootClockRUN(void)
while (DCDC_REG0_STS_DC_OK_MASK != (DCDC_REG0_STS_DC_OK_MASK & DCDC->REG0))
{
}
/* Init ARM PLL. */
CLOCK_InitArmPll(&armPllConfig_BOARD_BootClockRUN);
/* In SDK projects, SDRAM (configured by SEMC) will be initialized in either debug script or dcd.
* With this macro SKIP_SYSCLK_INIT, system pll (selected to be SEMC source clock in SDK projects) will be left unchanged.
* Note: If another clock source is selected for SEMC, user may want to avoid changing that clock as well.*/
#ifndef SKIP_SYSCLK_INIT
/* Init System PLL. */
CLOCK_InitSysPll(&sysPllConfig_BOARD_BootClockRUN);
/* Init System pfd0. */
CLOCK_InitSysPfd(kCLOCK_Pfd0, 27);
/* Init System pfd1. */
CLOCK_InitSysPfd(kCLOCK_Pfd1, 16);
/* Init System pfd2. */
CLOCK_InitSysPfd(kCLOCK_Pfd2, 24);
/* Init System pfd3. */
CLOCK_InitSysPfd(kCLOCK_Pfd3, 16);
#endif
/* In SDK projects, external flash (configured by FLEXSPI2) will be initialized by dcd.
* With this macro XIP_EXTERNAL_FLASH, usb1 pll (selected to be FLEXSPI2 clock source in SDK projects) will be left unchanged.
* Note: If another clock source is selected for FLEXSPI2, user may want to avoid changing that clock as well.*/
#if !(defined(XIP_EXTERNAL_FLASH) && (XIP_EXTERNAL_FLASH == 1))
/* Init Usb1 PLL. */
CLOCK_InitUsb1Pll(&usb1PllConfig_BOARD_BootClockRUN);
/* Init Usb1 pfd0. */
CLOCK_InitUsb1Pfd(kCLOCK_Pfd0, 33);
/* Init Usb1 pfd1. */
CLOCK_InitUsb1Pfd(kCLOCK_Pfd1, 16);
/* Init Usb1 pfd2. */
CLOCK_InitUsb1Pfd(kCLOCK_Pfd2, 17);
/* Init Usb1 pfd3. */
CLOCK_InitUsb1Pfd(kCLOCK_Pfd3, 19);
/* Disable Usb1 PLL output for USBPHY1. */
CCM_ANALOG->PLL_USB1 &= ~CCM_ANALOG_PLL_USB1_EN_USB_CLKS_MASK;
#endif
/* DeInit Audio PLL. */
CLOCK_DeinitAudioPll();
/* Bypass Audio PLL. */
CLOCK_SetPllBypass(CCM_ANALOG, kCLOCK_PllAudio, 1);
/* Set divider for Audio PLL. */
CCM_ANALOG->MISC2 &= ~CCM_ANALOG_MISC2_AUDIO_DIV_LSB_MASK;
CCM_ANALOG->MISC2 &= ~CCM_ANALOG_MISC2_AUDIO_DIV_MSB_MASK;
/* Enable Audio PLL output. */
CCM_ANALOG->PLL_AUDIO |= CCM_ANALOG_PLL_AUDIO_ENABLE_MASK;
/* DeInit Video PLL. */
CLOCK_DeinitVideoPll();
/* Bypass Video PLL. */
CCM_ANALOG->PLL_VIDEO |= CCM_ANALOG_PLL_VIDEO_BYPASS_MASK;
/* Set divider for Video PLL. */
CCM_ANALOG->MISC2 = (CCM_ANALOG->MISC2 & (~CCM_ANALOG_MISC2_VIDEO_DIV_MASK)) | CCM_ANALOG_MISC2_VIDEO_DIV(0);
/* Enable Video PLL output. */
CCM_ANALOG->PLL_VIDEO |= CCM_ANALOG_PLL_VIDEO_ENABLE_MASK;
/* DeInit Enet PLL. */
CLOCK_DeinitEnetPll();
/* Bypass Enet PLL. */
CLOCK_SetPllBypass(CCM_ANALOG, kCLOCK_PllEnet, 1);
/* Set Enet output divider. */
CCM_ANALOG->PLL_ENET = (CCM_ANALOG->PLL_ENET & (~CCM_ANALOG_PLL_ENET_DIV_SELECT_MASK)) | CCM_ANALOG_PLL_ENET_DIV_SELECT(1);
/* Enable Enet output. */
CCM_ANALOG->PLL_ENET |= CCM_ANALOG_PLL_ENET_ENABLE_MASK;
/* Set Enet2 output divider. */
CCM_ANALOG->PLL_ENET = (CCM_ANALOG->PLL_ENET & (~CCM_ANALOG_PLL_ENET_ENET2_DIV_SELECT_MASK)) | CCM_ANALOG_PLL_ENET_ENET2_DIV_SELECT(0);
/* Enable Enet2 output. */
CCM_ANALOG->PLL_ENET |= CCM_ANALOG_PLL_ENET_ENET2_REF_EN_MASK;
/* Enable Enet25M output. */
CCM_ANALOG->PLL_ENET |= CCM_ANALOG_PLL_ENET_ENET_25M_REF_EN_MASK;
/* DeInit Usb2 PLL. */
CLOCK_DeinitUsb2Pll();
/* Bypass Usb2 PLL. */
CLOCK_SetPllBypass(CCM_ANALOG, kCLOCK_PllUsb2, 1);
/* Enable Usb2 PLL output. */
CCM_ANALOG->PLL_USB2 |= CCM_ANALOG_PLL_USB2_ENABLE_MASK;
/* Set AHB_PODF. */
CLOCK_SetDiv(kCLOCK_AhbDiv, 0);
/* Disable IPG clock gate. */
......@@ -193,8 +260,14 @@ void BOARD_BootClockRUN(void)
CLOCK_SetDiv(kCLOCK_IpgDiv, 3);
/* Set ARM_PODF. */
CLOCK_SetDiv(kCLOCK_ArmDiv, 1);
/* Set preperiph clock source. */
CLOCK_SetMux(kCLOCK_PrePeriphMux, 3);
/* Set periph clock source. */
CLOCK_SetMux(kCLOCK_PeriphMux, 0);
/* Set PERIPH_CLK2_PODF. */
CLOCK_SetDiv(kCLOCK_PeriphClk2Div, 0);
/* Set periph clock2 clock source. */
CLOCK_SetMux(kCLOCK_PeriphClk2Mux, 0);
/* Disable PERCLK clock gate. */
CLOCK_DisableClock(kCLOCK_Gpt1);
CLOCK_DisableClock(kCLOCK_Gpt1S);
......@@ -203,6 +276,8 @@ void BOARD_BootClockRUN(void)
CLOCK_DisableClock(kCLOCK_Pit);
/* Set PERCLK_PODF. */
CLOCK_SetDiv(kCLOCK_PerclkDiv, 1);
/* Set per clock source. */
CLOCK_SetMux(kCLOCK_PerclkMux, 0);
/* Disable USDHC1 clock gate. */
CLOCK_DisableClock(kCLOCK_Usdhc1);
/* Set USDHC1_PODF. */
......@@ -241,9 +316,9 @@ void BOARD_BootClockRUN(void)
/* Disable Flexspi2 clock gate. */
CLOCK_DisableClock(kCLOCK_FlexSpi2);
/* Set FLEXSPI2_PODF. */
CLOCK_SetDiv(kCLOCK_Flexspi2Div, 1);
CLOCK_SetDiv(kCLOCK_Flexspi2Div, 0);
/* Set Flexspi2 clock source. */
CLOCK_SetMux(kCLOCK_Flexspi2Mux, 3);
CLOCK_SetMux(kCLOCK_Flexspi2Mux, 1);
#endif
/* Disable CSI clock gate. */
CLOCK_DisableClock(kCLOCK_Csi);
......@@ -325,9 +400,9 @@ void BOARD_BootClockRUN(void)
/* Disable LCDIF clock gate. */
CLOCK_DisableClock(kCLOCK_LcdPixel);
/* Set LCDIF_PRED. */
CLOCK_SetDiv(kCLOCK_LcdifPreDiv, 6);
CLOCK_SetDiv(kCLOCK_LcdifPreDiv, 1);
/* Set LCDIF_CLK_PODF. */
CLOCK_SetDiv(kCLOCK_LcdifDiv, 7);
CLOCK_SetDiv(kCLOCK_LcdifDiv, 3);
/* Set Lcdif pre clock source. */
CLOCK_SetMux(kCLOCK_LcdifPreMux, 5);
/* Disable SPDIF clock gate. */
......@@ -356,85 +431,6 @@ void BOARD_BootClockRUN(void)
CLOCK_SetMux(kCLOCK_Flexio2Mux, 3);
/* Set Pll3 sw clock source. */
CLOCK_SetMux(kCLOCK_Pll3SwMux, 0);
/* Init ARM PLL. */
CLOCK_InitArmPll(&armPllConfig_BOARD_BootClockRUN);
/* In SDK projects, SDRAM (configured by SEMC) will be initialized in either debug script or dcd.
* With this macro SKIP_SYSCLK_INIT, system pll (selected to be SEMC source clock in SDK projects) will be left unchanged.
* Note: If another clock source is selected for SEMC, user may want to avoid changing that clock as well.*/
#ifndef SKIP_SYSCLK_INIT
/* Init System PLL. */
CLOCK_InitSysPll(&sysPllConfig_BOARD_BootClockRUN);
/* Init System pfd0. */
CLOCK_InitSysPfd(kCLOCK_Pfd0, 27);
/* Init System pfd1. */
CLOCK_InitSysPfd(kCLOCK_Pfd1, 16);
/* Init System pfd2. */
CLOCK_InitSysPfd(kCLOCK_Pfd2, 24);
/* Init System pfd3. */
CLOCK_InitSysPfd(kCLOCK_Pfd3, 16);
#endif
/* In SDK projects, external flash (configured by FLEXSPI2) will be initialized by dcd.
* With this macro XIP_EXTERNAL_FLASH, usb1 pll (selected to be FLEXSPI2 clock source in SDK projects) will be left unchanged.
* Note: If another clock source is selected for FLEXSPI2, user may want to avoid changing that clock as well.*/
#if !(defined(XIP_EXTERNAL_FLASH) && (XIP_EXTERNAL_FLASH == 1))
/* Init Usb1 PLL. */
CLOCK_InitUsb1Pll(&usb1PllConfig_BOARD_BootClockRUN);
/* Init Usb1 pfd0. */
CLOCK_InitUsb1Pfd(kCLOCK_Pfd0, 33);
/* Init Usb1 pfd1. */
CLOCK_InitUsb1Pfd(kCLOCK_Pfd1, 16);
/* Init Usb1 pfd2. */
CLOCK_InitUsb1Pfd(kCLOCK_Pfd2, 17);
/* Init Usb1 pfd3. */
CLOCK_InitUsb1Pfd(kCLOCK_Pfd3, 19);
/* Disable Usb1 PLL output for USBPHY1. */
CCM_ANALOG->PLL_USB1 &= ~CCM_ANALOG_PLL_USB1_EN_USB_CLKS_MASK;
#endif
/* DeInit Audio PLL. */
CLOCK_DeinitAudioPll();
/* Bypass Audio PLL. */
CLOCK_SetPllBypass(CCM_ANALOG, kCLOCK_PllAudio, 1);
/* Set divider for Audio PLL. */
CCM_ANALOG->MISC2 &= ~CCM_ANALOG_MISC2_AUDIO_DIV_LSB_MASK;
CCM_ANALOG->MISC2 &= ~CCM_ANALOG_MISC2_AUDIO_DIV_MSB_MASK;
/* Enable Audio PLL output. */
CCM_ANALOG->PLL_AUDIO |= CCM_ANALOG_PLL_AUDIO_ENABLE_MASK;
/* DeInit Video PLL. */
CLOCK_DeinitVideoPll();
/* Bypass Video PLL. */
CCM_ANALOG->PLL_VIDEO |= CCM_ANALOG_PLL_VIDEO_BYPASS_MASK;
/* Set divider for Video PLL. */
CCM_ANALOG->MISC2 = (CCM_ANALOG->MISC2 & (~CCM_ANALOG_MISC2_VIDEO_DIV_MASK)) | CCM_ANALOG_MISC2_VIDEO_DIV(0);
/* Enable Video PLL output. */
CCM_ANALOG->PLL_VIDEO |= CCM_ANALOG_PLL_VIDEO_ENABLE_MASK;
/* DeInit Enet PLL. */
CLOCK_DeinitEnetPll();
/* Bypass Enet PLL. */
CLOCK_SetPllBypass(CCM_ANALOG, kCLOCK_PllEnet, 1);
/* Set Enet output divider. */
CCM_ANALOG->PLL_ENET = (CCM_ANALOG->PLL_ENET & (~CCM_ANALOG_PLL_ENET_DIV_SELECT_MASK)) | CCM_ANALOG_PLL_ENET_DIV_SELECT(1);
/* Enable Enet output. */
CCM_ANALOG->PLL_ENET |= CCM_ANALOG_PLL_ENET_ENABLE_MASK;
/* Set Enet2 output divider. */
CCM_ANALOG->PLL_ENET = (CCM_ANALOG->PLL_ENET & (~CCM_ANALOG_PLL_ENET_ENET2_DIV_SELECT_MASK)) | CCM_ANALOG_PLL_ENET_ENET2_DIV_SELECT(0);
/* Enable Enet2 output. */
CCM_ANALOG->PLL_ENET |= CCM_ANALOG_PLL_ENET_ENET2_REF_EN_MASK;
/* Enable Enet25M output. */
CCM_ANALOG->PLL_ENET |= CCM_ANALOG_PLL_ENET_ENET_25M_REF_EN_MASK;
/* DeInit Usb2 PLL. */
CLOCK_DeinitUsb2Pll();
/* Bypass Usb2 PLL. */
CLOCK_SetPllBypass(CCM_ANALOG, kCLOCK_PllUsb2, 1);
/* Enable Usb2 PLL output. */
CCM_ANALOG->PLL_USB2 |= CCM_ANALOG_PLL_USB2_ENABLE_MASK;
/* Set preperiph clock source. */
CLOCK_SetMux(kCLOCK_PrePeriphMux, 3);
/* Set periph clock source. */
CLOCK_SetMux(kCLOCK_PeriphMux, 0);
/* Set periph clock2 clock source. */
CLOCK_SetMux(kCLOCK_PeriphClk2Mux, 0);
/* Set per clock source. */
CLOCK_SetMux(kCLOCK_PerclkMux, 0);
/* Set lvds1 clock source. */
CCM_ANALOG->MISC1 = (CCM_ANALOG->MISC1 & (~CCM_ANALOG_MISC1_LVDS1_CLK_SEL_MASK)) | CCM_ANALOG_MISC1_LVDS1_CLK_SEL(0);
/* Set clock out1 divider. */
......@@ -451,26 +447,6 @@ void BOARD_BootClockRUN(void)
CCM->CCOSR &= ~CCM_CCOSR_CLKO1_EN_MASK;
/* Disable clock out2. */
CCM->CCOSR &= ~CCM_CCOSR_CLKO2_EN_MASK;
/* Set SAI1 MCLK1 clock source. */
IOMUXC_SetSaiMClkClockSource(IOMUXC_GPR, kIOMUXC_GPR_SAI1MClk1Sel, 0);
/* Set SAI1 MCLK2 clock source. */
IOMUXC_SetSaiMClkClockSource(IOMUXC_GPR, kIOMUXC_GPR_SAI1MClk2Sel, 0);
/* Set SAI1 MCLK3 clock source. */
IOMUXC_SetSaiMClkClockSource(IOMUXC_GPR, kIOMUXC_GPR_SAI1MClk3Sel, 0);
/* Set SAI2 MCLK3 clock source. */
IOMUXC_SetSaiMClkClockSource(IOMUXC_GPR, kIOMUXC_GPR_SAI2MClk3Sel, 0);
/* Set SAI3 MCLK3 clock source. */
IOMUXC_SetSaiMClkClockSource(IOMUXC_GPR, kIOMUXC_GPR_SAI3MClk3Sel, 0);
/* Set MQS configuration. */
IOMUXC_MQSConfig(IOMUXC_GPR,kIOMUXC_MqsPwmOverSampleRate32, 0);
/* Set ENET1 Tx clock source. */
IOMUXC_EnableMode(IOMUXC_GPR, kIOMUXC_GPR_ENET1RefClkMode, false);
/* Set ENET2 Tx clock source. */
IOMUXC_EnableMode(IOMUXC_GPR, IOMUXC_GPR_GPR1_ENET2_CLK_SEL_MASK, false);
/* Set GPT1 High frequency reference clock source. */
IOMUXC_GPR->GPR5 &= ~IOMUXC_GPR_GPR5_VREF_1M_CLK_GPT1_MASK;
/* Set GPT2 High frequency reference clock source. */
IOMUXC_GPR->GPR5 &= ~IOMUXC_GPR_GPR5_VREF_1M_CLK_GPT2_MASK;
/* Set SystemCoreClock variable. */
SystemCoreClock = BOARD_BOOTCLOCKRUN_CORE_CLOCK;
}
......
bsp/imxrt/imxrt1064-nxp-evk/board/SConscript
浏览文件 @ d6ff0fc0
......@@ -13,7 +13,11 @@ MCUX_Config/pin_mux.c
CPPPATH = [cwd,cwd + '/MCUX_Config',cwd + '/ports']
CPPDEFINES = ['CPU_MIMXRT1064DVL6A', 'STD=C99', 'SKIP_SYSCLK_INIT', 'EVK_MCIMXRM', 'FSL_SDK_ENABLE_DRIVER_CACHE_CONTROL','XIP_EXTERNAL_FLASH=1', 'XIP_BOOT_HEADER_ENABLE=1']
CPPDEFINES = ['CPU_MIMXRT1064DVL6A', 'SKIP_SYSCLK_INIT', 'EVK_MCIMXRM', 'FSL_SDK_ENABLE_DRIVER_CACHE_CONTROL=1','XIP_EXTERNAL_FLASH=1', 'XIP_BOOT_HEADER_ENABLE=1', 'XIP_BOOT_HEADER_DCD_ENABLE=1']
if GetDepend(['PHY_USING_KSZ8081']):
src += Glob('ports/phyksz8081/fsl_phy.c')
CPPPATH += [cwd + '/ports/phyksz8081']
if rtconfig.CROSS_TOOL == 'keil':
CPPDEFINES.append('__FPU_PRESENT=1')
......
bsp/imxrt/imxrt1064-nxp-evk/board/board.c
浏览文件 @ d6ff0fc0
......@@ -12,6 +12,8 @@
#include <rtthread.h>
#include "board.h"
#include "pin_mux.h"
#include "fsl_iomuxc.h"
#include "fsl_gpio.h"
#ifdef BSP_USING_DMA
#include "fsl_dmamux.h"
......@@ -109,6 +111,325 @@ void imxrt_dma_init(void)
EDMA_Init(DMA0, &config);
}
#endif
#ifdef BSP_USING_LPUART
void imxrt_uart_pins_init(void)
{
#ifdef BSP_USING_LPUART1
IOMUXC_SetPinMux(
IOMUXC_GPIO_AD_B0_12_LPUART1_TX, /* GPIO_AD_B0_12 is configured as LPUART1_TX */
0U); /* Software Input On Field: Input Path is determined by functionality */
IOMUXC_SetPinMux(
IOMUXC_GPIO_AD_B0_13_LPUART1_RX, /* GPIO_AD_B0_13 is configured as LPUART1_RX */
0U); /* Software Input On Field: Input Path is determined by functionality */
IOMUXC_SetPinConfig(
IOMUXC_GPIO_AD_B0_12_LPUART1_TX, /* GPIO_AD_B0_12 PAD functional properties : */
0x10B0u); /* Slew Rate Field: Slow Slew Rate
Drive Strength Field: R0/6
Speed Field: medium(100MHz)
Open Drain Enable Field: Open Drain Disabled
Pull / Keep Enable Field: Pull/Keeper Enabled
Pull / Keep Select Field: Keeper
Pull Up / Down Config. Field: 100K Ohm Pull Down
Hyst. Enable Field: Hysteresis Disabled */
IOMUXC_SetPinConfig(
IOMUXC_GPIO_AD_B0_13_LPUART1_RX, /* GPIO_AD_B0_13 PAD functional properties : */
0x10B0u); /* Slew Rate Field: Slow Slew Rate
Drive Strength Field: R0/6
Speed Field: medium(100MHz)
Open Drain Enable Field: Open Drain Disabled
Pull / Keep Enable Field: Pull/Keeper Enabled
Pull / Keep Select Field: Keeper
Pull Up / Down Config. Field: 100K Ohm Pull Down
Hyst. Enable Field: Hysteresis Disabled */
#endif
#ifdef BSP_USING_LPUART2
IOMUXC_SetPinMux(
IOMUXC_GPIO_AD_B1_02_LPUART2_TX,
0U);
IOMUXC_SetPinMux(
IOMUXC_GPIO_AD_B1_03_LPUART2_RX,
0U);
IOMUXC_SetPinConfig(
IOMUXC_GPIO_AD_B1_02_LPUART2_TX,
0x10B0u);
IOMUXC_SetPinConfig(
IOMUXC_GPIO_AD_B1_03_LPUART2_RX,
0x10B0u);
#endif
#ifdef BSP_USING_LPUART3
IOMUXC_SetPinMux(
IOMUXC_GPIO_AD_B1_06_LPUART3_TX,
0U);
IOMUXC_SetPinMux(
IOMUXC_GPIO_AD_B1_07_LPUART3_RX,
0U);
IOMUXC_SetPinConfig(
IOMUXC_GPIO_AD_B1_06_LPUART3_TX,
0x10B0u);
IOMUXC_SetPinConfig(
IOMUXC_GPIO_AD_B1_07_LPUART3_RX,
0x10B0u);
#endif
#ifdef BSP_USING_LPUART4
IOMUXC_SetPinMux(
IOMUXC_GPIO_B1_00_LPUART4_TX,
0U);
IOMUXC_SetPinMux(
IOMUXC_GPIO_B1_01_LPUART4_RX,
0U);
IOMUXC_SetPinConfig(
IOMUXC_GPIO_B1_00_LPUART4_TX,
0x10B0u);
IOMUXC_SetPinConfig(
IOMUXC_GPIO_B1_01_LPUART4_RX,
0x10B0u);
#endif
#ifdef BSP_USING_LPUART5
IOMUXC_SetPinMux(
IOMUXC_GPIO_B1_12_LPUART5_TX,
0U);
IOMUXC_SetPinMux(
IOMUXC_GPIO_B1_13_LPUART5_RX,
0U);
IOMUXC_SetPinConfig(
IOMUXC_GPIO_B1_12_LPUART5_TX,
0x10B0u);
IOMUXC_SetPinConfig(
IOMUXC_GPIO_B1_13_LPUART5_RX,
0x10B0u);
#endif
#ifdef BSP_USING_LPUART6
IOMUXC_SetPinMux(
IOMUXC_GPIO_AD_B0_02_LPUART6_TX,
0U);
IOMUXC_SetPinMux(
IOMUXC_GPIO_AD_B0_03_LPUART6_RX,
0U);
IOMUXC_SetPinConfig(
IOMUXC_GPIO_AD_B0_02_LPUART6_TX,
0x10B0u);
IOMUXC_SetPinConfig(
IOMUXC_GPIO_AD_B0_03_LPUART6_RX,
0x10B0u);
#endif
#ifdef BSP_USING_LPUART7
IOMUXC_SetPinMux(
IOMUXC_GPIO_EMC_31_LPUART7_TX,
0U);
IOMUXC_SetPinMux(
IOMUXC_GPIO_EMC_32_LPUART7_RX,
0U);
IOMUXC_SetPinConfig(
IOMUXC_GPIO_EMC_31_LPUART7_TX,
0x10B0u);
IOMUXC_SetPinConfig(
IOMUXC_GPIO_EMC_32_LPUART7_RX,
0x10B0u);
#endif
#ifdef BSP_USING_LPUART8
IOMUXC_SetPinMux(
IOMUXC_GPIO_AD_B1_10_LPUART8_TX,
0U);
IOMUXC_SetPinMux(
IOMUXC_GPIO_AD_B1_11_LPUART8_RX,
0U);
IOMUXC_SetPinConfig(
IOMUXC_GPIO_AD_B1_10_LPUART8_TX,
0x10B0u);
IOMUXC_SetPinConfig(
IOMUXC_GPIO_AD_B1_11_LPUART8_RX,
0x10B0u);
#endif
}
#endif /* BSP_USING_LPUART */
#ifdef BSP_USING_ETH
void imxrt_enet_pins_init(void)
{
CLOCK_EnableClock(kCLOCK_Iomuxc); /* iomuxc clock (iomuxc_clk_enable): 0x03u */
IOMUXC_SetPinMux(
IOMUXC_GPIO_AD_B0_09_GPIO1_IO09, /* GPIO_AD_B0_09 is configured as GPIO1_IO09 */
0U); /* Software Input On Field: Input Path is determined by functionality */
IOMUXC_SetPinMux(
IOMUXC_GPIO_AD_B0_10_GPIO1_IO10, /* GPIO_AD_B0_10 is configured as GPIO1_IO10 */
0U);
IOMUXC_SetPinMux(
IOMUXC_GPIO_B1_04_ENET_RX_DATA00, /* GPIO_B1_04 is configured as ENET_RX_DATA00 */
0U); /* Software Input On Field: Input Path is determined by functionality */
IOMUXC_SetPinMux(
IOMUXC_GPIO_B1_05_ENET_RX_DATA01, /* GPIO_B1_05 is configured as ENET_RX_DATA01 */
0U); /* Software Input On Field: Input Path is determined by functionality */
IOMUXC_SetPinMux(
IOMUXC_GPIO_B1_06_ENET_RX_EN, /* GPIO_B1_06 is configured as ENET_RX_EN */
0U); /* Software Input On Field: Input Path is determined by functionality */
IOMUXC_SetPinMux(
IOMUXC_GPIO_B1_07_ENET_TX_DATA00, /* GPIO_B1_07 is configured as ENET_TX_DATA00 */
0U); /* Software Input On Field: Input Path is determined by functionality */
IOMUXC_SetPinMux(
IOMUXC_GPIO_B1_08_ENET_TX_DATA01, /* GPIO_B1_08 is configured as ENET_TX_DATA01 */
0U); /* Software Input On Field: Input Path is determined by functionality */
IOMUXC_SetPinMux(
IOMUXC_GPIO_B1_09_ENET_TX_EN, /* GPIO_B1_09 is configured as ENET_TX_EN */
0U); /* Software Input On Field: Input Path is determined by functionality */
IOMUXC_SetPinMux(
IOMUXC_GPIO_B1_10_ENET_REF_CLK, /* GPIO_B1_10 is configured as ENET_REF_CLK */
1U); /* Software Input On Field: Force input path of pad GPIO_B1_10 */
IOMUXC_SetPinMux(
IOMUXC_GPIO_B1_11_ENET_RX_ER, /* GPIO_B1_11 is configured as ENET_RX_ER */
0U); /* Software Input On Field: Input Path is determined by functionality */
IOMUXC_SetPinMux(
IOMUXC_GPIO_EMC_40_ENET_MDC, /* GPIO_EMC_40 is configured as ENET_MDC */
0U); /* Software Input On Field: Input Path is determined by functionality */
IOMUXC_SetPinMux(
IOMUXC_GPIO_EMC_41_ENET_MDIO, /* GPIO_EMC_41 is configured as ENET_MDIO */
0U); /* Software Input On Field: Input Path is determined by functionality */
IOMUXC_SetPinConfig(
IOMUXC_GPIO_AD_B0_09_GPIO1_IO09, /* GPIO_AD_B0_09 PAD functional properties : */
0xB0A9u); /* Slew Rate Field: Fast Slew Rate
Drive Strength Field: R0/5
Speed Field: medium(100MHz)
Open Drain Enable Field: Open Drain Disabled
Pull / Keep Enable Field: Pull/Keeper Enabled
Pull / Keep Select Field: Pull
Pull Up / Down Config. Field: 100K Ohm Pull Up
Hyst. Enable Field: Hysteresis Disabled */
IOMUXC_SetPinConfig(
IOMUXC_GPIO_AD_B0_10_GPIO1_IO10, /* GPIO_AD_B0_10 PAD functional properties : */
0xB0A9u); /* Slew Rate Field: Fast Slew Rate
Drive Strength Field: R0/5
Speed Field: medium(100MHz)
Open Drain Enable Field: Open Drain Disabled
Pull / Keep Enable Field: Pull/Keeper Enabled
Pull / Keep Select Field: Pull
Pull Up / Down Config. Field: 100K Ohm Pull Up
Hyst. Enable Field: Hysteresis Disabled */
IOMUXC_SetPinConfig(
IOMUXC_GPIO_B1_04_ENET_RX_DATA00, /* GPIO_B1_04 PAD functional properties : */
0xB0E9u); /* Slew Rate Field: Fast Slew Rate
Drive Strength Field: R0/5
Speed Field: max(200MHz)
Open Drain Enable Field: Open Drain Disabled
Pull / Keep Enable Field: Pull/Keeper Enabled
Pull / Keep Select Field: Pull
Pull Up / Down Config. Field: 100K Ohm Pull Up
Hyst. Enable Field: Hysteresis Disabled */
IOMUXC_SetPinConfig(
IOMUXC_GPIO_B1_05_ENET_RX_DATA01, /* GPIO_B1_05 PAD functional properties : */
0xB0E9u); /* Slew Rate Field: Fast Slew Rate
Drive Strength Field: R0/5
Speed Field: max(200MHz)
Open Drain Enable Field: Open Drain Disabled
Pull / Keep Enable Field: Pull/Keeper Enabled
Pull / Keep Select Field: Pull
Pull Up / Down Config. Field: 100K Ohm Pull Up
Hyst. Enable Field: Hysteresis Disabled */
IOMUXC_SetPinConfig(
IOMUXC_GPIO_B1_06_ENET_RX_EN, /* GPIO_B1_06 PAD functional properties : */
0xB0E9u); /* Slew Rate Field: Fast Slew Rate
Drive Strength Field: R0/5
Speed Field: max(200MHz)
Open Drain Enable Field: Open Drain Disabled
Pull / Keep Enable Field: Pull/Keeper Enabled
Pull / Keep Select Field: Pull
Pull Up / Down Config. Field: 100K Ohm Pull Up
Hyst. Enable Field: Hysteresis Disabled */
IOMUXC_SetPinConfig(
IOMUXC_GPIO_B1_07_ENET_TX_DATA00, /* GPIO_B1_07 PAD functional properties : */
0xB0E9u); /* Slew Rate Field: Fast Slew Rate
Drive Strength Field: R0/5
Speed Field: max(200MHz)
Open Drain Enable Field: Open Drain Disabled
Pull / Keep Enable Field: Pull/Keeper Enabled
Pull / Keep Select Field: Pull
Pull Up / Down Config. Field: 100K Ohm Pull Up
Hyst. Enable Field: Hysteresis Disabled */
IOMUXC_SetPinConfig(
IOMUXC_GPIO_B1_08_ENET_TX_DATA01, /* GPIO_B1_08 PAD functional properties : */
0xB0E9u); /* Slew Rate Field: Fast Slew Rate
Drive Strength Field: R0/5
Speed Field: max(200MHz)
Open Drain Enable Field: Open Drain Disabled
Pull / Keep Enable Field: Pull/Keeper Enabled
Pull / Keep Select Field: Pull
Pull Up / Down Config. Field: 100K Ohm Pull Up
Hyst. Enable Field: Hysteresis Disabled */
IOMUXC_SetPinConfig(
IOMUXC_GPIO_B1_09_ENET_TX_EN, /* GPIO_B1_09 PAD functional properties : */
0xB0E9u); /* Slew Rate Field: Fast Slew Rate
Drive Strength Field: R0/5
Speed Field: max(200MHz)
Open Drain Enable Field: Open Drain Disabled
Pull / Keep Enable Field: Pull/Keeper Enabled
Pull / Keep Select Field: Pull
Pull Up / Down Config. Field: 100K Ohm Pull Up
Hyst. Enable Field: Hysteresis Disabled */
IOMUXC_SetPinConfig(
IOMUXC_GPIO_B1_10_ENET_REF_CLK, /* GPIO_B1_10 PAD functional properties : */
0x31u); /* Slew Rate Field: Fast Slew Rate
Drive Strength Field: R0/6
Speed Field: low(50MHz)
Open Drain Enable Field: Open Drain Disabled
Pull / Keep Enable Field: Pull/Keeper Disabled
Pull / Keep Select Field: Keeper
Pull Up / Down Config. Field: 100K Ohm Pull Down
Hyst. Enable Field: Hysteresis Disabled */
IOMUXC_SetPinConfig(
IOMUXC_GPIO_B1_11_ENET_RX_ER, /* GPIO_B1_11 PAD functional properties : */
0xB0E9u); /* Slew Rate Field: Fast Slew Rate
Drive Strength Field: R0/5
Speed Field: max(200MHz)
Open Drain Enable Field: Open Drain Disabled
Pull / Keep Enable Field: Pull/Keeper Enabled
Pull / Keep Select Field: Pull
Pull Up / Down Config. Field: 100K Ohm Pull Up
Hyst. Enable Field: Hysteresis Disabled */
IOMUXC_SetPinConfig(
IOMUXC_GPIO_EMC_40_ENET_MDC, /* GPIO_EMC_40 PAD functional properties : */
0xB0E9u); /* Slew Rate Field: Fast Slew Rate
Drive Strength Field: R0/5
Speed Field: max(200MHz)
Open Drain Enable Field: Open Drain Disabled
Pull / Keep Enable Field: Pull/Keeper Enabled
Pull / Keep Select Field: Pull
Pull Up / Down Config. Field: 100K Ohm Pull Up
Hyst. Enable Field: Hysteresis Disabled */
IOMUXC_SetPinConfig(
IOMUXC_GPIO_EMC_41_ENET_MDIO, /* GPIO_EMC_41 PAD functional properties : */
0xB829u); /* Slew Rate Field: Fast Slew Rate
Drive Strength Field: R0/5
Speed Field: low(50MHz)
Open Drain Enable Field: Open Drain Enabled
Pull / Keep Enable Field: Pull/Keeper Enabled
Pull / Keep Select Field: Pull
Pull Up / Down Config. Field: 100K Ohm Pull Up
Hyst. Enable Field: Hysteresis Disabled */
}
void imxrt_enet_phy_reset_by_gpio(void)
{
gpio_pin_config_t gpio_config = {kGPIO_DigitalOutput, 0, kGPIO_NoIntmode};
GPIO_PinInit(GPIO1, 9, &gpio_config);
GPIO_PinInit(GPIO1, 10, &gpio_config);
/* pull up the ENET_INT before RESET. */
GPIO_WritePinOutput(GPIO1, 10, 1);
GPIO_WritePinOutput(GPIO1, 9, 0);
rt_thread_delay(100);
GPIO_WritePinOutput(GPIO1, 9, 1);
}
#endif /* BSP_USING_ETH */
/**
* This function will initial rt1050 board.
*/
......@@ -121,6 +442,14 @@ void rt_hw_board_init()
NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_4);
SysTick_Config(SystemCoreClock / RT_TICK_PER_SECOND);
#ifdef BSP_USING_LPUART
imxrt_uart_pins_init();
#endif
#ifdef BSP_USING_ETH
imxrt_enet_pins_init();
#endif
#ifdef BSP_USING_DMA
imxrt_dma_init();
#endif
......
bsp/imxrt/imxrt1064-nxp-evk/board/board.h
浏览文件 @ d6ff0fc0
......@@ -45,5 +45,11 @@ extern int heap_end;
void rt_hw_board_init(void);
#ifdef BSP_USING_ETH
void imxrt_enet_pins_init(void);
void imxrt_enet_phy_reset_by_gpio(void);
#define PHY_ADDRESS 0x02u
#endif
#endif
bsp/imxrt/imxrt1064-nxp-evk/board/ports/phyksz8081/fsl_phy.c 0 → 100644
浏览文件 @ d6ff0fc0
/*
* Copyright (c) 2015, Freescale Semiconductor, Inc.
* Copyright 2016-2017 NXP
* All rights reserved.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
#include "fsl_phy.h"
#include <rtthread.h>
/*******************************************************************************
* Definitions
******************************************************************************/
/*! @brief Defines the timeout macro. */
#define PHY_TIMEOUT_COUNT 0x3FFFFFFU
/*******************************************************************************
* Prototypes
******************************************************************************/
/*!
* @brief Get the ENET instance from peripheral base address.
*
* @param base ENET peripheral base address.
* @return ENET instance.
*/
extern uint32_t ENET_GetInstance(ENET_Type *base);
/*******************************************************************************
* Variables
******************************************************************************/
#if !(defined(FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) && FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL)
/*! @brief Pointers to enet clocks for each instance. */
extern clock_ip_name_t s_enetClock[FSL_FEATURE_SOC_ENET_COUNT];
#endif /* FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL */
/*******************************************************************************
* Code
******************************************************************************/
status_t PHY_Init(ENET_Type *base, uint32_t phyAddr, uint32_t srcClock_Hz)
{
uint32_t bssReg;
uint32_t counter = PHY_TIMEOUT_COUNT;
uint32_t idReg = 0;
status_t result = kStatus_Success;
uint32_t instance = ENET_GetInstance(base);
uint32_t timeDelay;
uint32_t ctlReg = 0;
#if !(defined(FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) && FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL)
/* Set SMI first. */
CLOCK_EnableClock(s_enetClock[instance]);
#endif /* FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL */
ENET_SetSMI(base, srcClock_Hz, false);
/* Initialization after PHY stars to work. */
while ((idReg != PHY_CONTROL_ID1) && (counter != 0))
{
PHY_Read(base, phyAddr, PHY_ID1_REG, &idReg);
counter --;
}
if (!counter)
{
return kStatus_Fail;
}
/* Reset PHY. */
counter = PHY_TIMEOUT_COUNT;
result = PHY_Write(base, phyAddr, PHY_BASICCONTROL_REG, PHY_BCTL_RESET_MASK);
if (result == kStatus_Success)
{
#if defined(FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE)
uint32_t data = 0;
result = PHY_Read(base, phyAddr, PHY_CONTROL2_REG, &data);
if ( result != kStatus_Success)
{
return result;
}
result = PHY_Write(base, phyAddr, PHY_CONTROL2_REG, (data | PHY_CTL2_REFCLK_SELECT_MASK));
if (result != kStatus_Success)
{
return result;
}
#endif /* FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE */
/* Set the negotiation. */
result = PHY_Write(base, phyAddr, PHY_AUTONEG_ADVERTISE_REG,
(PHY_100BASETX_FULLDUPLEX_MASK | PHY_100BASETX_HALFDUPLEX_MASK |
PHY_10BASETX_FULLDUPLEX_MASK | PHY_10BASETX_HALFDUPLEX_MASK | 0x1U));
if (result == kStatus_Success)
{
result = PHY_Write(base, phyAddr, PHY_BASICCONTROL_REG,
(PHY_BCTL_AUTONEG_MASK | PHY_BCTL_RESTART_AUTONEG_MASK));
if (result == kStatus_Success)
{
/* Check auto negotiation complete. */
while (counter --)
{
result = PHY_Read(base, phyAddr, PHY_BASICSTATUS_REG, &bssReg);
if ( result == kStatus_Success)
{
PHY_Read(base, phyAddr, PHY_CONTROL1_REG, &ctlReg);
if (((bssReg & PHY_BSTATUS_AUTONEGCOMP_MASK) != 0) && (ctlReg & PHY_LINK_READY_MASK))
{
/* Wait a moment for Phy status stable. */
for (timeDelay = 0; timeDelay < PHY_TIMEOUT_COUNT; timeDelay ++)
{
__ASM("nop");
}
break;
}
}
if (!counter)
{
return kStatus_PHY_AutoNegotiateFail;
}
}
}
}
}
return result;
}
status_t PHY_Write(ENET_Type *base, uint32_t phyAddr, uint32_t phyReg, uint32_t data)
{
uint32_t counter;
/* Clear the SMI interrupt event. */
ENET_ClearInterruptStatus(base, ENET_EIR_MII_MASK);
/* Starts a SMI write command. */
ENET_StartSMIWrite(base, phyAddr, phyReg, kENET_MiiWriteValidFrame, data);
/* Wait for SMI complete. */
for (counter = PHY_TIMEOUT_COUNT; counter > 0; counter--)
{
if (ENET_GetInterruptStatus(base) & ENET_EIR_MII_MASK)
{
break;
}
}
/* Check for timeout. */
if (!counter)
{
return kStatus_PHY_SMIVisitTimeout;
}
/* Clear MII interrupt event. */
ENET_ClearInterruptStatus(base, ENET_EIR_MII_MASK);
return kStatus_Success;
}
status_t PHY_Read(ENET_Type *base, uint32_t phyAddr, uint32_t phyReg, uint32_t *dataPtr)
{
assert(dataPtr);
uint32_t counter;
/* Clear the MII interrupt event. */
ENET_ClearInterruptStatus(base, ENET_EIR_MII_MASK);
/* Starts a SMI read command operation. */
ENET_StartSMIRead(base, phyAddr, phyReg, kENET_MiiReadValidFrame);
/* Wait for MII complete. */
for (counter = PHY_TIMEOUT_COUNT; counter > 0; counter--)
{
if (ENET_GetInterruptStatus(base) & ENET_EIR_MII_MASK)
{
break;
}
}
/* Check for timeout. */
if (!counter)
{
return kStatus_PHY_SMIVisitTimeout;
}
/* Get data from MII register. */
*dataPtr = ENET_ReadSMIData(base);
/* Clear MII interrupt event. */
ENET_ClearInterruptStatus(base, ENET_EIR_MII_MASK);
return kStatus_Success;
}
status_t PHY_EnableLoopback(ENET_Type *base, uint32_t phyAddr, phy_loop_t mode, phy_speed_t speed, bool enable)
{
status_t result;
uint32_t data = 0;
/* Set the loop mode. */
if (enable)
{
if (mode == kPHY_LocalLoop)
{
if (speed == kPHY_Speed100M)
{
data = PHY_BCTL_SPEED_100M_MASK | PHY_BCTL_DUPLEX_MASK | PHY_BCTL_LOOP_MASK;
}
else
{
data = PHY_BCTL_DUPLEX_MASK | PHY_BCTL_LOOP_MASK;
}
return PHY_Write(base, phyAddr, PHY_BASICCONTROL_REG, data);
}
else
{
/* First read the current status in control register. */
result = PHY_Read(base, phyAddr, PHY_CONTROL2_REG, &data);
if (result == kStatus_Success)
{
return PHY_Write(base, phyAddr, PHY_CONTROL2_REG, (data | PHY_CTL2_REMOTELOOP_MASK));
}
}
}
else
{
/* Disable the loop mode. */
if (mode == kPHY_LocalLoop)
{
/* First read the current status in control register. */
result = PHY_Read(base, phyAddr, PHY_BASICCONTROL_REG, &data);
if (result == kStatus_Success)
{
data &= ~PHY_BCTL_LOOP_MASK;
return PHY_Write(base, phyAddr, PHY_BASICCONTROL_REG, (data | PHY_BCTL_RESTART_AUTONEG_MASK));
}
}
else
{
/* First read the current status in control one register. */
result = PHY_Read(base, phyAddr, PHY_CONTROL2_REG, &data);
if (result == kStatus_Success)
{
return PHY_Write(base, phyAddr, PHY_CONTROL2_REG, (data & ~PHY_CTL2_REMOTELOOP_MASK));
}
}
}
return result;
}
status_t PHY_GetLinkStatus(ENET_Type *base, uint32_t phyAddr, bool *status)
{
assert(status);
status_t result = kStatus_Success;
uint32_t data;
/* Read the basic status register. */
result = PHY_Read(base, phyAddr, PHY_BASICSTATUS_REG, &data);
if (result == kStatus_Success)
{
if (!(PHY_BSTATUS_LINKSTATUS_MASK & data))
{
/* link down. */
*status = false;
}
else
{
/* link up. */
*status = true;
}
}
return result;
}
status_t PHY_GetLinkSpeedDuplex(ENET_Type *base, uint32_t phyAddr, phy_speed_t *speed, phy_duplex_t *duplex)
{
assert(duplex);
status_t result = kStatus_Success;
uint32_t data, ctlReg;
/* Read the control two register. */
result = PHY_Read(base, phyAddr, PHY_CONTROL1_REG, &ctlReg);
if (result == kStatus_Success)
{
data = ctlReg & PHY_CTL1_SPEEDUPLX_MASK;
if ((PHY_CTL1_10FULLDUPLEX_MASK == data) || (PHY_CTL1_100FULLDUPLEX_MASK == data))
{
/* Full duplex. */
*duplex = kPHY_FullDuplex;
}
else
{
/* Half duplex. */
*duplex = kPHY_HalfDuplex;
}
data = ctlReg & PHY_CTL1_SPEEDUPLX_MASK;
if ((PHY_CTL1_100HALFDUPLEX_MASK == data) || (PHY_CTL1_100FULLDUPLEX_MASK == data))
{
/* 100M speed. */
*speed = kPHY_Speed100M;
}
else
{ /* 10M speed. */
*speed = kPHY_Speed10M;
}
}
return result;
}
bsp/imxrt/imxrt1064-nxp-evk/board/ports/phyksz8081/fsl_phy.h 0 → 100644
浏览文件 @ d6ff0fc0
/*
* Copyright (c) 2015, Freescale Semiconductor, Inc.
* Copyright 2016-2017 NXP
* All rights reserved.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
#ifndef _FSL_PHY_H_
#define _FSL_PHY_H_
#include "fsl_enet.h"
/*!
* @addtogroup phy_driver
* @{
*/
/*******************************************************************************
* Definitions
******************************************************************************/
/*! @brief PHY driver version */
#define FSL_PHY_DRIVER_VERSION (MAKE_VERSION(2, 0, 0)) /*!< Version 2.0.0. */
/*! @brief Defines the PHY registers. */
#define PHY_BASICCONTROL_REG 0x00U /*!< The PHY basic control register. */
#define PHY_BASICSTATUS_REG 0x01U /*!< The PHY basic status register. */
#define PHY_ID1_REG 0x02U /*!< The PHY ID one register. */
#define PHY_ID2_REG 0x03U /*!< The PHY ID two register. */
#define PHY_AUTONEG_ADVERTISE_REG 0x04U /*!< The PHY auto-negotiate advertise register. */
#define PHY_CONTROL1_REG 0x1EU /*!< The PHY control one register. */
#define PHY_CONTROL2_REG 0x1FU /*!< The PHY control two register. */
#define PHY_CONTROL_ID1 0x22U /*!< The PHY ID1*/
/*! @brief Defines the mask flag in basic control register. */
#define PHY_BCTL_DUPLEX_MASK 0x0100U /*!< The PHY duplex bit mask. */
#define PHY_BCTL_RESTART_AUTONEG_MASK 0x0200U /*!< The PHY restart auto negotiation mask. */
#define PHY_BCTL_AUTONEG_MASK 0x1000U /*!< The PHY auto negotiation bit mask. */
#define PHY_BCTL_SPEED_MASK 0x2000U /*!< The PHY speed bit mask. */
#define PHY_BCTL_LOOP_MASK 0x4000U /*!< The PHY loop bit mask. */
#define PHY_BCTL_RESET_MASK 0x8000U /*!< The PHY reset bit mask. */
#define PHY_BCTL_SPEED_100M_MASK 0x2000U /*!< The PHY 100M speed mask. */
/*!@brief Defines the mask flag of operation mode in control two register*/
#define PHY_CTL2_REMOTELOOP_MASK 0x0004U /*!< The PHY remote loopback mask. */
#define PHY_CTL2_REFCLK_SELECT_MASK 0x0080U /*!< The PHY RMII reference clock select. */
#define PHY_CTL1_10HALFDUPLEX_MASK 0x0001U /*!< The PHY 10M half duplex mask. */
#define PHY_CTL1_100HALFDUPLEX_MASK 0x0002U /*!< The PHY 100M half duplex mask. */
#define PHY_CTL1_10FULLDUPLEX_MASK 0x0005U /*!< The PHY 10M full duplex mask. */
#define PHY_CTL1_100FULLDUPLEX_MASK 0x0006U /*!< The PHY 100M full duplex mask. */
#define PHY_CTL1_SPEEDUPLX_MASK 0x0007U /*!< The PHY speed and duplex mask. */
#define PHY_CTL1_ENERGYDETECT_MASK 0x10U /*!< The PHY signal present on rx differential pair. */
#define PHY_CTL1_LINKUP_MASK 0x100U /*!< The PHY link up. */
#define PHY_LINK_READY_MASK (PHY_CTL1_ENERGYDETECT_MASK | PHY_CTL1_LINKUP_MASK)
/*! @brief Defines the mask flag in basic status register. */
#define PHY_BSTATUS_LINKSTATUS_MASK 0x0004U /*!< The PHY link status mask. */
#define PHY_BSTATUS_AUTONEGABLE_MASK 0x0008U /*!< The PHY auto-negotiation ability mask. */
#define PHY_BSTATUS_AUTONEGCOMP_MASK 0x0020U /*!< The PHY auto-negotiation complete mask. */
/*! @brief Defines the mask flag in PHY auto-negotiation advertise register. */
#define PHY_100BaseT4_ABILITY_MASK 0x200U /*!< The PHY have the T4 ability. */
#define PHY_100BASETX_FULLDUPLEX_MASK 0x100U /*!< The PHY has the 100M full duplex ability.*/
#define PHY_100BASETX_HALFDUPLEX_MASK 0x080U /*!< The PHY has the 100M full duplex ability.*/
#define PHY_10BASETX_FULLDUPLEX_MASK 0x040U /*!< The PHY has the 10M full duplex ability.*/
#define PHY_10BASETX_HALFDUPLEX_MASK 0x020U /*!< The PHY has the 10M full duplex ability.*/
/*! @brief Defines the PHY status. */
enum _phy_status
{
kStatus_PHY_SMIVisitTimeout = MAKE_STATUS(kStatusGroup_PHY, 1), /*!< ENET PHY SMI visit timeout. */
kStatus_PHY_AutoNegotiateFail = MAKE_STATUS(kStatusGroup_PHY, 2) /*!< ENET PHY AutoNegotiate Fail. */
};
/*! @brief Defines the PHY link speed. This is align with the speed for ENET MAC. */
typedef enum _phy_speed
{
kPHY_Speed10M = 0U, /*!< ENET PHY 10M speed. */
kPHY_Speed100M /*!< ENET PHY 100M speed. */
} phy_speed_t;
/*! @brief Defines the PHY link duplex. */
typedef enum _phy_duplex
{
kPHY_HalfDuplex = 0U, /*!< ENET PHY half duplex. */
kPHY_FullDuplex /*!< ENET PHY full duplex. */
} phy_duplex_t;
/*! @brief Defines the PHY loopback mode. */
typedef enum _phy_loop
{
kPHY_LocalLoop = 0U, /*!< ENET PHY local loopback. */
kPHY_RemoteLoop /*!< ENET PHY remote loopback. */
} phy_loop_t;
/*******************************************************************************
* API
******************************************************************************/
#if defined(__cplusplus)
extern "C" {
#endif
/*!
* @name PHY Driver
* @{
*/
/*!
* @brief Initializes PHY.
*
* This function initialize the SMI interface and initialize PHY.
* The SMI is the MII management interface between PHY and MAC, which should be
* firstly initialized before any other operation for PHY. The PHY initialize with auto-negotiation.
*
* @param base ENET peripheral base address.
* @param phyAddr The PHY address.
* @param srcClock_Hz The module clock frequency - system clock for MII management interface - SMI.
* @retval kStatus_Success PHY initialize success
* @retval kStatus_PHY_SMIVisitTimeout PHY SMI visit time out
* @retval kStatus_PHY_AutoNegotiateFail PHY auto negotiate fail
*/
status_t PHY_Init(ENET_Type *base, uint32_t phyAddr, uint32_t srcClock_Hz);
/*!
* @brief PHY Write function. This function write data over the SMI to
* the specified PHY register. This function is called by all PHY interfaces.
*
* @param base ENET peripheral base address.
* @param phyAddr The PHY address.
* @param phyReg The PHY register.
* @param data The data written to the PHY register.
* @retval kStatus_Success PHY write success
* @retval kStatus_PHY_SMIVisitTimeout PHY SMI visit time out
*/
status_t PHY_Write(ENET_Type *base, uint32_t phyAddr, uint32_t phyReg, uint32_t data);
/*!
* @brief PHY Read function. This interface read data over the SMI from the
* specified PHY register. This function is called by all PHY interfaces.
*
* @param base ENET peripheral base address.
* @param phyAddr The PHY address.
* @param phyReg The PHY register.
* @param dataPtr The address to store the data read from the PHY register.
* @retval kStatus_Success PHY read success
* @retval kStatus_PHY_SMIVisitTimeout PHY SMI visit time out
*/
status_t PHY_Read(ENET_Type *base, uint32_t phyAddr, uint32_t phyReg, uint32_t *dataPtr);
/*!
* @brief Enables/disables PHY loopback.
*
* @param base ENET peripheral base address.
* @param phyAddr The PHY address.
* @param mode The loopback mode to be enabled, please see "phy_loop_t".
* the two loopback mode should not be both set. when one loopback mode is set
* the other one should be disabled.
* @param speed PHY speed for loopback mode.
* @param enable True to enable, false to disable.
* @retval kStatus_Success PHY loopback success
* @retval kStatus_PHY_SMIVisitTimeout PHY SMI visit time out
*/
status_t PHY_EnableLoopback(ENET_Type *base, uint32_t phyAddr, phy_loop_t mode, phy_speed_t speed, bool enable);
/*!
* @brief Gets the PHY link status.
*
* @param base ENET peripheral base address.
* @param phyAddr The PHY address.
* @param status The link up or down status of the PHY.
* - true the link is up.
* - false the link is down.
* @retval kStatus_Success PHY get link status success
* @retval kStatus_PHY_SMIVisitTimeout PHY SMI visit time out
*/
status_t PHY_GetLinkStatus(ENET_Type *base, uint32_t phyAddr, bool *status);
/*!
* @brief Gets the PHY link speed and duplex.
*
* @param base ENET peripheral base address.
* @param phyAddr The PHY address.
* @param speed The address of PHY link speed.
* @param duplex The link duplex of PHY.
* @retval kStatus_Success PHY get link speed and duplex success
* @retval kStatus_PHY_SMIVisitTimeout PHY SMI visit time out
*/
status_t PHY_GetLinkSpeedDuplex(ENET_Type *base, uint32_t phyAddr, phy_speed_t *speed, phy_duplex_t *duplex);
/* @} */
#if defined(__cplusplus)
}
#endif
/*! @}*/
#endif /* _FSL_PHY_H_ */
bsp/imxrt/imxrt1064-nxp-evk/board/ports/sdram_port.h 0 → 100644
浏览文件 @ d6ff0fc0
/*
* Copyright (c) 2006-2018, RT-Thread Development Team
*
* SPDX-License-Identifier: Apache-2.0
*
* Change Logs:
* Date Author Notes
* 2018-12-05 zylx The first version for STM32F4xx
* 2019-4-25 misonyo port to IMXRT
*/
#ifndef SDRAM_PORT_H__
#define SDRAM_PORT_H__
/* parameters for sdram peripheral */
#define SDRAM_BANK_ADDR ((uint32_t)0x80000000U)
/* region#0/1/2/3: kSEMC_SDRAM_CS0/1/2/3 */
#define SDRAM_REGION kSEMC_SDRAM_CS0
/* CS pin: kSEMC_MUXCSX0/1/2/3 */
#define SDRAM_CS_PIN kSEMC_MUXCSX0
/* size(kbyte):32MB = 32*1024*1KBytes */
#define SDRAM_SIZE ((uint32_t)0x8000)
/* data width: kSEMC_PortSize8Bit,kSEMC_PortSize16Bit */
#define SDRAM_DATA_WIDTH kSEMC_PortSize16Bit
/* column bit numbers: kSEMC_SdramColunm_9/10/11/12bit */
#define SDRAM_COLUMN_BITS kSEMC_SdramColunm_9bit
/* cas latency clock number: kSEMC_LatencyOne/Two/Three */
#define SDRAM_CAS_LATENCY kSEMC_LatencyThree
/* Timing configuration for W9825G6KH */
/* TRP:precharge to active command time (ns) */
#define SDRAM_TRP 18
/* TRCD:active to read/write command delay time (ns) */
#define SDRAM_TRCD 18
/* The time between two refresh commands,Use the maximum of the (Trfc , Txsr).(ns) */
#define SDRAM_REFRESH_RECOVERY 67
/* TWR:write recovery time (ns). */
#define SDRAM_TWR 12
/* TRAS:active to precharge command time (ns). */
#define SDRAM_TRAS 42
/* TRC time (ns). */
#define SDRAM_TRC 60
/* active to active time (ns). */
#define SDRAM_ACT2ACT 60
/* refresh time (ns). 64ms */
#define SDRAM_REFRESH_ROW 64 * 1000000 / 8192
#endif /* SDRAM_PORT_H__ */
bsp/imxrt/imxrt1064-nxp-evk/rtconfig.py
浏览文件 @ d6ff0fc0
......@@ -48,7 +48,7 @@ if PLATFORM == 'gcc':
DEVICE = ' -mcpu=' + CPU + ' -mthumb -mfpu=fpv5-d16 -mfloat-abi=hard -ffunction-sections -fdata-sections'
CFLAGS = DEVICE + ' -Wall -D__FPU_PRESENT -eentry'
AFLAGS = ' -c' + DEVICE + ' -x assembler-with-cpp -Wa,-mimplicit-it=thumb -D__START=entry'
LFLAGS = DEVICE + ' -lm -lgcc -lc' + ' -nostartfiles -Wl,--gc-sections,-Map=rtthread.map,-cref,-u,Reset_Handler -T board/linker_scripts/link.lds'
LFLAGS = DEVICE + ' -lm -lgcc -lc' + ' -nostartfiles -Wl,--gc-sections,-Map=rtthread.map,-cref,-u,Reset_Handler -T board/linker_scripts/link.lds -Xlinker -print-memory-usage'
CPATH = ''
LPATH = ''
......@@ -57,8 +57,8 @@ if PLATFORM == 'gcc':
AFLAGS += ' -D__STARTUP_CLEAR_BSS'
if BUILD == 'debug':
CFLAGS += ' -gdwarf-2'
AFLAGS += ' -gdwarf-2'
CFLAGS += ' -g'
AFLAGS += ' -g'
CFLAGS += ' -O0'
else:
CFLAGS += ' -O2 -Os'
......
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或