This document records the guide of the BSP (board support package) provided by the RT-Thread development team for the STM32F103C8 Blue Pill development board.
This document records the introduction of the BSP (board support package) provided by the RT-Thread development team for the STM32F103C8 Blue Pill development board.
The document is covered in four parts:
...
...
@@ -17,9 +17,9 @@ By reading the ***Quickly Get Started*** section developers can quickly get thei
## Onboard Resources
The "blue pill" is a STM32F103 based development board with Cortex-M3 ARM CPU that runs at 72 MHz, 20 kB of RAM and 64 or 128 kB of flash memory. The microcontroller (MCU) has USB port, two serial ports, 16 bit PWM pins and 12 bit ADC pins. It runs at 3.3V, but some of its pins are 5V tolerant.
The "blue pill" is a STM32F103 based development board with Cortex-M3 ARM CPU that runs at 72 MHz, 20 KB of RAM and 64 or 128 KB of flash memory. The microcontroller (MCU) has a USB port, two serial ports, 16 bit PWM pins and 12 bit ADC pins. It runs at 3.3V, but some of its pins are 5V tolerant.
- MCU：STM32F103C8T6 @72MHz, 64KB FLASH , 20KB RAM
- MCU：STM32F103C8T6 @72MHz, 64KB FLASH , 20KB RAM
- Peripherals
...
...
@@ -27,9 +27,8 @@ The "blue pill" is a STM32F103 based development board with Cortex-M3 ARM CPU th
- Debug IO interface type: SWD / ST-LINK
...
...
@@ -43,17 +42,17 @@ This BSP provides MDK4, MDK5, and IAR projects for developers and it supports th
1) Use a Type-A to Mini-B cable to connect the development board to the PC and turn on the power switch.
2) Use FTDI adapter(USB to UART) to connect the BluePill board's PA9(Tx) and PA10(Rx) pins.
2) Use FTDI adapter(USB to UART) to connect the BluePill board's PA9(Tx) and PA10(Rx) pins.
### Compile and Download
Double-click the `project.uvprojx` file, to open the MDK5 project, compile and download the program to the board.
Double-click the `project.uvprojx` file to open the MDK5 project; compile and download the program to the board.
### Running Results
After the program is successfully downloaded, the system runs automatically. Observe the running results of the LED on the development board, and you will see LED is flashing periodically.
After the program is successfully downloaded, the system runs automatically. Observe the running results of the LED on the development board, and you will see the LED is flashing periodically.
The USB virtual COM port connects to USART1(PA9-Tx, PA10-Rx) by default, and when the corresponding serial port (115200-8-1-N) is opened in the terminal tool, the output information of RT-Thread can be seen when the device is reset:
...
...
@@ -69,9 +68,9 @@ msh >
## **Advanced Features**
This BSP only enables GPIO and USART2 by default. If you need more advanced features such as SPI, I2C, you need to configure the BSP with RT-Thread [ENV tools](https://www.rt-thread.io/download.html?download=Env), as follows:
This BSP only enables GPIO and USART1 by default. If you need more advanced features such as SPI, ADC, or to add software packages, you need to configure the BSP with RT-Thread [ENV tools](https://www.rt-thread.io/download.html?download=Env), as follows:
1. Open the ENV tool under the specific BSP folder;
1. Open the ENV tool under the specific BSP folder, eg: *bsp/stm32/stm32f103-blue-pill*;
2. Enter `menuconfig` command to configure the project, then save and exit;
3. Enter `pkgs --update` command to update the package;
4. Enter `scons --target=mdk4/mdk5/iar` command to regenerate the project.
...
...
@@ -82,10 +81,9 @@ Learn how to use RT-Thread ENV, click [Here](https://github.com/RT-Thread/rtthre
