Kconfig

menu "Hardware Drivers Config"

config SOC_STM32F469NI
    bool
    select SOC_SERIES_STM32F4
    default y

menu "Onboard Peripheral Drivers"
    config BSP_USING_SDRAM
        bool "Enable SDRAM"
        select BSP_USING_FMC
        default n

    config BSP_USING_LCD_MIPI
        bool
        default n
        
    config BSP_USING_LCD_OTM8009A
        bool "Enable LCD OTM8009A"
        select BSP_USING_SDRAM
        select BSP_USING_LTDC
        select BSP_USING_LCD_MIPI
        default n
        
    config BSP_USING_QSPI_FLASH
        bool "Enable QSPI FLASH (N25Q128A qspi1)"
        select BSP_USING_QSPI
        select RT_USING_SFUD
        select RT_SFUD_USING_QSPI
        select PKG_USING_FAL
        select FAL_USING_SFUD_PORT
        default n
        
    config BSP_MOUNT_QSPI_WITH_LFS
        bool "Mount QSPI flash to / with little fs"
        depends on BSP_USING_QSPI_FLASH
        select PKG_USING_LITTLEFS
        select RT_USING_MTD_NOR
        select RT_USING_DFS
        default y
        
    config BSP_USING_SDCARD
        bool "Enable SDCARD (sdio)"
        select BSP_USING_SDIO
        select RT_USING_DFS
        select RT_USING_DFS_ELMFAT
        select RT_USING_PIN
        default n
    if BSP_USING_SDCARD
    config SDIO_MAX_FREQ
        int "sdio max freq"
        range 0 24000000
        default 24000000
    endif
        
    config BSP_USING_TOUCH
        bool "Enable TOUCH"
        select BSP_USING_I2C1
        default n
        if BSP_USING_TOUCH
            config BSP_TOUCH_INT_PIN
                int "Touch interrupt pin"
                default 149
            config BSP_I2C_NAME
                string "I2C Bus Name"
                default "i2c1"
        endif
endmenu

menu "On-chip Peripheral Drivers"
    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        select RT_USING_SERIAL
        default y
        if BSP_USING_UART
            config BSP_USING_UART3
                bool "Enable UART3"
                default y

            config BSP_UART3_RX_USING_DMA
                bool "Enable UART3 RX DMA"
                depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
                default n
        endif
        
    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        default n
        if BSP_USING_I2C1
            comment "Notice: PB8 --> 24; PB9 --> 25" 
            config BSP_I2C1_SCL_PIN
                int "I2C1 scl pin number"
                range 1 176
                default 24
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 1 176
                default 25
        endif

    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        select RT_USING_SPI
        default n
        if BSP_USING_SPI  
            config BSP_USING_SPI3
                bool "Enable SPI3 BUS"
                default n        

            config BSP_SPI3_TX_USING_DMA
                bool "Enable SPI3 TX DMA"
                depends on BSP_USING_SPI3
                default n
                
            config BSP_SPI3_RX_USING_DMA
                bool "Enable SPI3 RX DMA"
                depends on BSP_USING_SPI3
                select BSP_SPI3_TX_USING_DMA
                default n  
        endif
    
    config BSP_USING_QSPI
        bool "Enable QSPI BUS"
        select RT_USING_QSPI
        select RT_USING_SPI
        default n

    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n

    config BSP_USING_FMC
        bool "Enable FMC"
        default n
        
    config BSP_USING_SDIO
        bool "Enable SDIO"
        select RT_USING_SDIO
        select RT_USING_DFS
        default n

    config BSP_USING_USBD_FS
        bool "Enable OTGFS as USB device"
        select RT_USING_USB_DEVICE
        default n

    config BSP_USING_LTDC
        bool "Enable LTDC"
        default n
    source "../libraries/HAL_Drivers/Kconfig.crypto"
    
endmenu

menu "Board extended module Drivers"

endmenu
 
endmenu