- 11 7月, 2007 10 次提交
-
-
由 Michal Schmidt 提交于
Don't turn the radio on until the interface is up. This saves some power in case the driver is loaded but the card is not used. Signed-off-by: NMichal Schmidt <mschmidt@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Michal Schmidt 提交于
Callers of enable_MAC() shouldn't have to worry about the bits in the response's status word (and most of them don't). The return value is sufficient information. Signed-off-by: NMichal Schmidt <mschmidt@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Michal Schmidt 提交于
Matteo Croce reported Aironet initialization failures. They were caused by a race in airo. airo finds a free interface name, then initializes the card and finally registers the interface. Another device may get the same name in the meantime. The reason airo gets its name early is to use it in informative printks and to name the resources it requests. The printks will be just fine without the interface name and the resources can use the driver's name - that's what other network drivers do anyway. One of the talkative functions is setup_card(). It is called once before registration and can be called later again. Let's have an empty dev->name during the first call, so it doesn't print the ugly "airo(eth%d)" message. Signed-off-by: NMichal Schmidt <mschmidt@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Michal Schmidt 提交于
airo's kernel thread and the IRQ handler are needed only when the interface is up. Signed-off-by: NMichal Schmidt <mschmidt@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Michal Schmidt 提交于
Fix an assymetry between pci_{enable,disable}_device. airo did not disable the PCI device when unloading the module. This caused suspend failures after modprobe -r airo && modprobe airo. Signed-off-by: NMichal Schmidt <mschmidt@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stephen Hemminger 提交于
Similar patch to ipw2200. Round the timer used for RF kill switch off to 1 second boundary to save power. Build tested only, don't have this hardware. Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stephen Hemminger 提交于
Make the ipw2200 driver polling of rf kill switch occur on second boundaries to reduce power. Making all the wakeup's in the system occur together reduces power, and keeps CPU in idle longer. Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Michael Wu 提交于
I failed to notice that a u16 was being passed to the hardware. This fixes it. Thanks to Kasper F. Brandt for finding this! Signed-off-by: NMichael Wu <flamingice@sourmilk.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
... by removing an ill-conceived, useless line. Discovered by coverity. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Robert P. J. Day 提交于
Remove a header file that was ostensibly "removed" before, in commit 3ce40232. Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 10 7月, 2007 30 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (31 commits) firewire: fw-sbp2: fix DMA mapping of management ORBs firewire: fw-sbp2: fix DMA mapping of command ORBs firewire: fw-sbp2: fix DMA mapping of S/G tables firewire: fw-sbp2: add a boundary check firewire: fw-sbp2: correctly align page tables firewire: fw-sbp2: memset wants string.h firewire: fw-sbp2: use correct speed in sbp2_agent_reset firewire: fw-sbp2: correctly dereference by container_of firewire: Document userspace ioctl interface. firewire: fw-sbp2: implement nonexclusive login firewire: fw-sbp2: let SCSI shutdown commands through before logout firewire: fw-sbp2: implement max sectors limit for some old bridges firewire: simplify a struct type firewire: support S100B...S400B and link slower than PHY firewire: optimize gap count with 1394b leaf nodes firewire: remove unused macro firewire: missing newline in printk firewire: fw-sbp2: remove unused struct member ieee1394: remove old isochronous ABI ieee1394: sbp2: change some module parameters from int to bool ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: HID: handle cases of volume knobs generating relative values HID: Logitech keyboard 0xc311 needs reset leds quirk HID: support for logitech cordless desktop LX500 special mapping HID: fix autocentering of PID devices HID: separate quirks for report descriptor fixup HID: Add NOGET quirk for all NCR devices HID: support for Petalynx Maxter remote control HID: fix mismatch between hid-input HUT find/search mapping and the HUT HID: support for Gameron dual psx adaptor USB HID: avoid flush_scheduled_work() HID: Use menuconfig objects HID: force hid-input for Microsoft SideWinder GameVoice device HID: input mapping for Chicony KU-0418 tactical pad HID: make debugging output runtime-configurable
-
由 Linus Torvalds 提交于
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (75 commits) Ethernet driver for EISA only SNI RM200/RM400 machines Extract chip specific code out of lasi_82596.c ehea: Whitespace cleanup pasemi_mac: Fix TX interrupt threshold spidernet: Replace literal with const r8169: perform RX config change after mac filtering r8169: mac address change support r8169: display some extra debug information during startup r8169: add endianess annotations to [RT]xDesc r8169: align the IP header when there is no DMA constraint r8169: add bit description for the TxPoll register r8169: cleanup r8169: remove the media option r8169: small 8101 comment r8169: confusion between hardware and IP header alignment r8169: merge with version 8.001.00 of Realtek's r8168 driver r8169: merge with version 6.001.00 of Realtek's r8169 driver r8169: prettify mac_version r8169: populate the hw_start handler for the 8110 r8169: populate the hw_start handler for the 8168 ...
-
由 Stefan Richter 提交于
The CPU must not touch the buffer after it was DMA-mapped. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: NKristian Høgsberg <krh@redhat.com>
-
由 Stefan Richter 提交于
The CPU must not touch the buffer after it was DMA-mapped. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: NKristian Høgsberg <krh@redhat.com>
-
由 Stefan Richter 提交于
- The CPU must not touch the buffer after it was DMA-mapped. - The size argument of dma_unmap_single(...page_table...) was bogus. - Move a comment closer to the code to which it refers to. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: NKristian Høgsberg <krh@redhat.com>
-
由 Stefan Richter 提交于
Add rudimentary check for the case that the page table overflows due to merging of s/g elements by the IOMMU. This would have lead to overwriting of arbitrary memory. After this change I expect that an offending command will be unsuccessfully retried until the scsi_device is taken offline by SCSI core. It's a border case and not worth to implement a recovery strategy. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Acked-by: NKristian Høgsberg <krh@redhat.com>
-
由 Stefan Richter 提交于
This is required per SBP-2 clause 5.2. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Acked-by: NKristian Høgsberg <krh@redhat.com>
-
由 Stefan Richter 提交于
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Acked-by: NKristian Høgsberg <krh@redhat.com>
-
由 Stefan Richter 提交于
noticed by Jay Fenlason Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Acked-by: NKristian Høgsberg <krh@redhat.com>
-
由 Jay Fenlason 提交于
Replace a cast with a container_of(). As long as nobody reorders the structure elements, they do the same thing, but container_of() is more readable. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added complete_command_orb) Acked-by: NKristian Høgsberg <krh@redhat.com>
-
由 Kristian Høgsberg 提交于
The isochronous packet format is still not documented, but this is a good first step. Signed-off-by: NKristian Høgsberg <krh@redhat.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (format, wording)
-
由 Stefan Richter 提交于
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: NKristian Høgsberg <krh@redhat.com>
-
由 Stefan Richter 提交于
This affects of course only the "soft shutdown" case, e.g. "modprobe -r firewire-sbp2", while it doesn't matter for hot unplug. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: NKristian Høgsberg <krh@redhat.com>
-
由 Stefan Richter 提交于
This currently only affects one bridge in the hardwired blacklist. I don't own one of those, hence haven't tested it. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
-
由 Stefan Richter 提交于
cleanup after "firewire: support S100B...S400B and link slower than PHY" Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: NKristian Høgsberg <krh@redhat.com>
-
由 Stefan Richter 提交于
Use a speed probe to determine the speed over 1394b buses and of nodes which report a link speed less than their PHY speed. Log the effective maximum speed of newly created nodes in dmesg. Also, read the config ROM (except bus info block) at the maximum speed rather than S100. This isn't a real optimization though because we still only use quadlet read requests for the entire ROM. The patch also adds support for S1600 and S3200, although such hardware does not exist yet. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: NKristian Høgsberg <krh@redhat.com>
-
由 Stefan Richter 提交于
Table-based gap count optimization cannot be used if 1394b repeater PHYs are present. But it does work with 1394b leaf nodes. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: NKristian Høgsberg <krh@redhat.com>
-
由 Stefan Richter 提交于
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
-
由 Stefan Richter 提交于
Also remove some errno printouts which will be shown by infrastructure code anyway. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
-
由 Stefan Richter 提交于
cleanup after support of single-buffer requests was dropped Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
-
由 Stefan Richter 提交于
Based on patch "the scheduled removal of RAW1394_REQ_ISO_{SEND,LISTEN}" from Adrian Bunk, November 20 2006. This patch also removes the underlying facilities in ohci1394 and disables them in pcilynx. That is, hpsb_host_driver.devctl() and hpsb_host_driver.transmit_packet() are no longer used for iso reception and transmission. Since video1394 and dv1394 only work with ohci1394 and raw1394's rawiso interface has never been implemented in pcilynx, pcilynx is now no longer useful for isochronous applications. raw1394 will still handle the request types but will complete the requests with errors that indicate API version conflicts. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
-
由 Stefan Richter 提交于
This is upwards compatible, except that integer values other than 0 or 1 are no longer accepted. But values like "Y", "N", "no", "nnoooh!" work now. Also, improve a comment on the serialize_io parameter and make the ORB_SET_EXCLUSIVE macro ultra-safe. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
-
由 Stefan Richter 提交于
Association of a host device with a node on NUMA machines optimizes allocations of skbs given from the networking stack to eth1394. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
-
由 Stefan Richter 提交于
After ieee1394 was converted away from class_device like the networking subsystem was already in 2.6.21, eth1394's device may point to the fw-host device as its parent again like in 2.6.20. This affects userspace tools which examine the sysfs representation of eth1394's device. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
-
由 Stefan Richter 提交于
Remove the global nodemgr_serialize mutex which enclosed most of the host thread event loop. This allows for parallelism between several host adapter cards. Properly serialize the driver hooks .update(), .suspend(), .resume(), and .remove() by means of device->sem. These hooks can be called from outside the host threads' contexts. Get() and put() the device.driver when calling its hooks. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
-
由 Kay Sievers 提交于
Here is a straightforward conversion to "struct device". The "struct class_device" will be removed from the kernel. It seems to work fine for me with and without CONFIG_SYSFS_DEPRECATED set. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
-
由 Stefan Richter 提交于
I was told that only i386 aligns 64 bit integers at 4 bytes boundaries while all other architectures (32 bit architectures with 64 bit siblings) align it on 8 bytes boundaries. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
-
由 Stefan Richter 提交于
Pointed out by Arnd Bergmann: PPC32 aligns this at 64bit, IA32 packs it. A kernel-wide available __compat_u64 which is 4-byte aligned on AMD64 and IA64 would be nicer though. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
-
由 Petr Vandrovec 提交于
Add compat_ioctl. Although all structures are more or less same, raw1394_iso_packets got pointer inside, and raw1394_cycle_timer got unwanted padding in the middle. I did not add any translation for ioctls passing array of integers around as integers seem to have same size (32 bits) on all architectures supported by Linux. Signed-off-by: NPetr Vandrovec <petr@vandrovec.name> Acked-by: NDan Dennedy <dan@dennedy.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (split into 3 patches)
-