This patch puts into place the final piece of the puzzle for SMP
support on ARM.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

Since we have to use XCB=101 instead of XCB=000 on the ixp2400 to
prevent it from regularly falling over, and since we have to deal with
manual write buffer flushing because of that, we might as well use
XCB=101 on all ixp2000 platforms since it's faster than XCB=000.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

nwfpe extended precision emulation used to be broken on big-endian
and was therefore disabled.  This patch fixes nwfpe so that it copies
extended precision floats to/from userspace in the proper word order
(similar to patch #2046, see the description of that patch for an
explanation) and reenables the Kconfig option.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

The routine that nwfpe uses for converting floats/doubles to
extended precision fails to zero two bytes of kernel stack.  This
is not immediately obvious, as the floatx80 structure has 16 bits
of implicit padding (by design.)  These two bytes are copied to
userspace when an stfe is emulated, causing a possible info leak.

Make the padding explicit and zero it out in the relevant places.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add SMP support for the MPcore tile fitted to the Realview ARM
platform.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add uniprocessor support for Realview platform fitted with the
MPcore (SMP) tile.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We need to set the shared memory attribute in the page tables
on SMP systems to allow the cache coherency to operate.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Adds a new CONFIG_PPC_64K_PAGES which, when enabled, changes the kernel
base page size to 64K.  The resulting kernel still boots on any
hardware.  On current machines with 4K pages support only, the kernel
will maintain 16 "subpages" for each 64K page transparently.

Note that while real 64K capable HW has been tested, the current patch
will not enable it yet as such hardware is not released yet, and I'm
still verifying with the firmware architects the proper to get the
information from the newer hypervisors.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

glibc expects to count lines beginning with "processor" to determine
the number of processors, not lines beginning with "Processor".  So,
give glibc the format it expects.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We don't want to call dump_cpu_info() from cpu_init() after boot since
it produces a lot of unnecessary noise - since cpu_init() gets called
on resume and hotplug cpu insertion events.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

// disagrees with ld's script parsing ability.  Don't use it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Richard Purdie

Update the PXA pm.c file to allow machines (such as the Sharp
Zaurus) to override the standard pm functions but reuse/wrap them
where needed.

The init call is made slightly earlier to give machine code an init
level to override them in removing any race.

Signed-off-by: Richard Purdie
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

Since we know the value of cpsr on entry, we can replace the bic+orr with
a single eor.  Also remove a possible result delay (at least on XScale).
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

Make the uengine loader use ixp2000_reg_wrb in the right places.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Alessandro Zummo

  This patch fixes AHB/PCI endianness problems when the
 processor is in little-endian mode.

 The patch configures the CSR register closely following the directives
 in [1], paragraph 4.1, page 19.

 According to the considerations in [1], page 11, while the AHB bus
 supports both endian modes, on the IXP4XX it always uses big-endian.

 The PCI bus is connected to the South AHB. A wrong setting in the CSR
 register will thus cause a malfunctional PCI bus.

 A schematic diagram of the bus interconnections on the IXP4XX
 can be found in [1], page 18.

 The patch has been verified to work on the NSLU2 in
 both LE and BE modes.

 The author is Peter Korsgaard.

 [1] Intel® IXP4XX Product Line of Network Processors and IXC1100
 Control Plane Processor:
 Understanding Big Endian and Little Endian Modes

 http://www.intel.com/design/network/applnots/25423701.pdfSigned-off-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Dirk Opfer

This patch adds basic machine support for the Sharp SL-6000x (Tosa) PDAs.

Signed-off-by: Dirk Opfer
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

From: Than Ngo <than@redhat.com>
qt as installed on fedora core (2 and 3) does not work with vanilla
kernel. The linker fails to locate the qt lib:

Actual Results:  # make xconfig
  HOSTLD  scripts/kconfig/qconf
  /usr/bin/ld: cannot find -lqt
  collect2: ld returned 1 exit status

Than Ngo has provided following fix for the bug.

Cc: Than Ngo <than@redhat.com>
Acked-by: NDave Jones <davej@redhat.com>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Include autoconf.h into every kernel compilation via the gcc command line
using -imacros.  This ensures that we have the kernel configuration
included from the start, rather than relying on each file having #include
<linux/config.h> as appropriate.  History has shown that this is something
which is difficult to get right.

Since we now include the kernel configuration automatically, make
configcheck becomes meaningless, so remove it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

The offsets of the registers are in a different place, and
some parts cannot handle a full set of modem control signals.
Signed-off-by: NPantelis Antoniou <pantelis@embeddedalley.ocm>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

my patch "x86: initialise tss->io_bitmap_owner to something" (commit ID
d5cd4aad) introduced a problem with a
program (DOSEMU) that called ioperm after already doing some port i/o.

The problem is that a process switch return causes tss->io_bitmap_base
to be set to IO_BITMAP_OFFSET so that the fault (that *really* sets the
io bitmap) never triggers.

This fixes that regression.
Signed-off-by: NBart Oldeman <bartoldeman@users.sourceforge.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Some visually impaired people use hardware devices which directly read
the vga screen. When newt for instance asks to hide the cursor for
better visual aspect, the kernel puts the vga cursor out of the screen,
so that the cursor position can't be read by the hardware device. This
is a great loss for such people.

Here is a patch which uses the same technique as CUR_NONE for hiding the
cursor while still moving it.

Mario, you should apply it to the speakup kernel for access floppies
asap. I'll submit a 2.4 patch too.

Signed-off-by: samuel.thibault@ens-lyon.org
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Statically allocated devices in module data is a potential cause
of oopsen.  The device may be in use by a userspace process, which
will keep a reference to the device.  If the module is unloaded,
the module data will be freed.  Subsequent use of the platform
device will cause a kernel oops.

Use generic platform device allocation/release code in modules.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

Statically allocated devices in module data is a potential cause
of oopsen.  The device may be in use by a userspace process, which
will keep a reference to the device.  If the module is unloaded,
the module data will be freed.  Subsequent use of the platform
device will cause a kernel oops.

Use generic platform device allocation/release code in modules.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device.  If the module is unloaded, the module
text will be freed.  Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.

Use generic platform device allocation/release code in modules.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device.  If the module is unloaded, the module
text will be freed.  Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.

Use generic platform device allocation/release code in modules.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device.  If the module is unloaded, the module
text will be freed.  Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.

Use generic platform device allocation/release code in modules.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device.  If the module is unloaded, the module
text will be freed.  Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.

Use generic platform device allocation/release code in modules.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

Re-jig the simple platform device support to allow private data
to be attached to a platform device, as well as allowing the
parent device to be set.

Example usage:

	pdev = platform_device_alloc("mydev", id);
	if (pdev) {
		err = platform_device_add_resources(pdev, &resources,
						    ARRAY_SIZE(resources));
		if (err == 0)
			err = platform_device_add_data(pdev, &platform_data,
						       sizeof(platform_data));
		if (err == 0)
			err = platform_device_add(pdev);
	} else {
		err = -ENOMEM;
	}
	if (err)
		platform_device_put(pdev);
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds a phy_mask field to struct mii_bus and uses it.  This field
indicates each phy address to be ignored when probing the mdio bus.

This support is needed for the fs_enet and ibm_emac drivers to be
converted to the generic phy layer among other drivers. Many systems
lock up on probing certain phy addresses or probing doesn't return
0xffff when nothing is found at the address. A new driver I'm
working on also makes use of this mask.
Signed-off-by: NMatt Porter <mporter@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Some boards using the 79c976 pcnet32 chip will hang the system if the
ethtool --register-dump is performed with the device operational.  The
request to read bcr30 is retried by the PCI device infinitely without
returning data, hanging the system.

Tested ia32 and ppc64.
Signed-off-by: NDon Fry <brazilnut@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch is a better fix for Allied Telesyn 2700/2701 FX boards than
the change made in early January this year.  It allows the user to
select the speed/duplex via module_param, but if no selection is made,
forces the speed to 100 FD.  It fixes both Bugzilla bugs 2669 and 4551.
Tested ia32 and ppc64 by myself, and by the originator of bug 2669.
Signed-off-by: NDon Fry <brazilnut@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>