According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.

On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.

On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.

There are a few issues with this approach

1. A host initiated resume will also generate a resume event. The event
   handler will find the port in resume state, believe it's a device
   initiated resume, and act accordingly.

2. A port status request might cut the resume signalling short if a
   get_port_status request is handled during the host resume signalling.
   The port will be found in resume state. The timestamp is not set leading
   to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
   get_port_status will proceed with moving the port to U0.

3. If an error, or anything else happens to the port during device
   initiated resume signalling it will leave all the device resume
   parameters hanging uncleared, preventing further suspend, returning
   -EBUSY, and cause the pm thread to busyloop trying to enter suspend.

Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state

This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS

Cc: stable <stable@vger.kernel.org>
Reported-by: NDaniel J Blueman <daniel@quora.org>
Tested-by: NDaniel J Blueman <daniel@quora.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'fixes-for-v4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for-v4.4-rc5

Hopefully final set of fixes for v4.4 release cycle.

There's a fix for a regression on dwc3 caused by recent changes to how
transfers are started. We're not pre-starting interrupt endpoints
anymore.

A NULL pointer dereference fix for the MSM phy driver.

The UVC gadget got a minor fix for permissions to its configfs
attributes and, finally, two fixes for MUSB. A fix for PM runtime when
MUSB returns EPROBE_DEFER and a fix to actually return an error in case
we can't initialize a DMA engine.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fail with error when no DMA controller is set.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

76e0da34 "usb-gadget/uvc: use per-attribute show and store methods"
removed write permission for writeable attributes. Correct attribute
permissions.

Fixes: 76e0da34 "usb-gadget/uvc: use per-attribute show and store methods"
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If musb_init_controller fails at musb_platform_init, we have already
called pm_runtime_irq_safe for musb and that causes the pm runtime count
to be enabled for parent before the parent has completed initialization.
This causes pm to stop working as on unload nothing gets idled.

This issue can be reproduced at least with:

# modprobe omap2430
HS USB OTG: no transceiver configured
musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
# modprobe phy-twl4030-usb
# rmmod omap2430

And after the steps above omap2430 will block deeper idle states on
omap3.

To fix this, let's not enable pm runtime until we need to and the
parent has been initialized. Note that this does not fix the issue of
PM being broken for musb during runtime.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Even if the probability of this case is very low, fixing it made
static analyzers happy.
Solving this with of_device_get_match_data made also code simplier.

Reported-by: coverity (CID 1324133)
Signed-off-by: NLABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The interrupt handler, ohci_hcd_at91_overcurrent_irq may be called right
after registration. At that time, pdev->dev.platform_data is not yet set,
leading to a NULL pointer dereference.

Fixes: e4df9227 (USB: host: ohci-at91: merge loops in ohci_hcd_at91_drv_probe)
Reported-by: NPeter Rosin <peda@axentia.se>
Tested-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org # 4.3+
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

My recent Intel box is spewing these messages:

xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: xHCI Host Controller
usb usb2: Manufacturer: Linux 4.3.0+ xhci-hcd
usb usb2: SerialNumber: 0000:00:14.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
usb: failed to peer usb2-port2 and usb1-port1 by location (usb2-port2:none) (usb1-port1:usb2-port1)
usb usb2-port2: failed to peer to usb1-port1 (-16)
usb: port power management may be unreliable
usb: failed to peer usb2-port3 and usb1-port1 by location (usb2-port3:none) (usb1-port1:usb2-port1)
usb usb2-port3: failed to peer to usb1-port1 (-16)
usb: failed to peer usb2-port5 and usb1-port1 by location (usb2-port5:none) (usb1-port1:usb2-port1)
usb usb2-port5: failed to peer to usb1-port1 (-16)
usb: failed to peer usb2-port6 and usb1-port1 by location (usb2-port6:none) (usb1-port1:usb2-port1)
usb usb2-port6: failed to peer to usb1-port1 (-16)

Diving into the acpi tables, I noticed the EHCI hub has 12 ports while the XHCI
hub has 8 ports.  Most of those ports are of connect type USB_PORT_NOT_USED
(including port 1 of the EHCI hub).

Further the unused ports have location data initialized to 0x80000000.

Now each unused port on the xhci hub walks the port list and finds a matching
peer with port1 of the EHCI hub because the zero'd out group id bits falsely match.
After port1 of the XHCI hub, each following matching peer will generate the
above warning.

These warnings seem to be harmless for this scenario as I don't think it
matters that unused ports could not create a peer link.

The attached patch utilizes that assumption and just turns the pr_warn into
pr_debug to quiet things down.

Tested on my Intel box.
Signed-off-by: NDon Zickus <dzickus@redhat.com>
Acked-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a memory leak because acpi_evaluate_dsm() actually returns an
object which the caller is supposed to release. Fix this by calling
ACPI_FREE() for the returned object (this expands to kfree() so passing
NULL there is fine as well).

While there correct indentation in !CONFIG_ACPI case.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.2
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_parse_ss_endpoint_companion() now decodes the burst multiplier
correctly in order to check that it's <= 3, but still uses the wrong
expression if warning that it's > 3.

Fixes: ff30cbc8 ("usb: Use the USB_SS_MULT() macro to get the ...")
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

qset_fill_page_list() do not check for dma mapping errors.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When a USB 3.0 mass storage device is disconnected in transporting
state, storage device driver may handle it as a transport error and
reset the device by invoking usb_reset_and_verify_device()
and following could happen:

in usb_reset_and_verify_device():
   udev->bos = NULL;

For U1/U2 enabled devices, driver will disable LPM, and in some
conditions:
   from usb_unlocked_disable_lpm()
    --> usb_disable_lpm()
    --> usb_enable_lpm()
        udev->bos->ss_cap->bU1devExitLat;

And it causes 'NULL pointer' and 'kernel panic':

[  157.976257] Unable to handle kernel NULL pointer dereference
at virtual address 00000010
...
[  158.026400] PC is at usb_enable_link_state+0x34/0x2e0
[  158.031442] LR is at usb_enable_lpm+0x98/0xac
...
[  158.137368] [<ffffffc0006a1cac>] usb_enable_link_state+0x34/0x2e0
[  158.143451] [<ffffffc0006a1fec>] usb_enable_lpm+0x94/0xac
[  158.148840] [<ffffffc0006a20e8>] usb_disable_lpm+0xa8/0xb4
...
[  158.214954] Kernel panic - not syncing: Fatal exception

This commit moves 'udev->bos = NULL' behind usb_unlocked_disable_lpm()
to prevent from NULL pointer access.

Issue can be reproduced by following setup:
1) A SS pen drive behind a SS hub connected to the host.
2) Transporting data between the pen drive and the host.
3) Abruptly disconnect hub and pen drive from host.
4) With a chance it crashes.
Signed-off-by: NHans Yang <hansy@nvidia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

All ELAN hid devices seem to require the ALWAYS_POLL quirk. Let's use
this quirk for all devices from this vendor, rather than maintaining a
list of all its known product IDs.
Tested-by: NAdrien Vergé <adrienverge@gmail.com>
Signed-off-by: NAdrien Vergé <adrienverge@gmail.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The patch extends the family of SATA-to-USB JMicron adapters that need
FUA to be disabled and applies the same policy for uas driver.
See details in http://unix.stackexchange.com/questions/237204/Signed-off-by: NDmitry Katsubo <dmitry.katsubo@gmail.com>
Tested-by: NDmitry Katsubo <dmitry.katsubo@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Like other buggy models that had their fixes [1], the touchscreen with
id 04f3:21b8 from ELAN Microelectronics needs the device-qualifier
quirk. Otherwise, it fails to respond, blocks the boot for a random
amount of time and pollutes dmesg with:

[ 2887.373196] usb 1-5: new full-speed USB device number 41 using xhci_hcd
[ 2889.502000] usb 1-5: unable to read config index 0 descriptor/start: -71
[ 2889.502005] usb 1-5: can't read configurations, error -71
[ 2889.654571] usb 1-5: new full-speed USB device number 42 using xhci_hcd
[ 2891.783438] usb 1-5: unable to read config index 0 descriptor/start: -71
[ 2891.783443] usb 1-5: can't read configurations, error -71

[1]: See commits c68929f7, 876af5d4, d7499475, a32c99e7 and dc703ec2.
Tested-by: NAdrien Vergé <adrienverge@gmail.com>
Signed-off-by: NAdrien Vergé <adrienverge@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-serial-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for v4.4-rc3

Here are some device-id fixes that remove a HID device from cp210x, and
adds support for another Infineon flash-loader device. The flash-loader
device presents itself as a CDC-ACM device even though it is clearly
not, so we need to blacklist it in the cdc-acm driver as well.
Signed-off-by: NJohan Hovold <johan@kernel.org>

Merge tag 'fixes-for-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v4.4-rc3

Here's our second round of fixes. Some of the bugs are pretty old like
the one on pxa27x suspend implementation.

The most important part is a randbuild warning fix on MUSB CPPI DMA
engine by Arnd, a couple fixes by Felipe Tonello on f_midi (first one
makes sure we only transmit on enabled ep IN while second plugs a memory
leak) and a NULL pointer dereference fix on renesas usbhs.

Note that we also have a new compatible string being added for the MXS
PHY.

Because interrupt endpoints usually transmit such
small amounts of data, it seems pointless to prestart
transfers and try to get speed improvements. This
patch also sorts out a problem with CDC ECM function
where its notification endpoint gets stuck in busy
state and we continuously issue Update Transfer
commands.

Fixes: 8a1a9c9e ("usb: dwc3: gadget: start transfer on XFER_COMPLETE")
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Pull nouveau and radeon fixes from Dave Airlie:
 "Just some nouveau and radeon/amdgpu fixes.

  The nouveau fixes look large as the firmware context files are
  regenerated, but the actual change is quite small"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: make some dpm errors debug only
  drm/nouveau/volt/pwm/gk104: fix an off-by-one resulting in the voltage not being set
  drm/nouveau/nvif: allow userspace access to its own client object
  drm/nouveau/gr/gf100-: fix oops when calling zbc methods
  drm/nouveau/gr/gf117-: assume no PPC if NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK is zero
  drm/nouveau/gr/gf117-: read NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK from correct GPC
  drm/nouveau/gr/gf100-: split out per-gpc address calculation macro
  drm/nouveau/bios: return actual size of the buffer retrieved via _ROM
  drm/nouveau/instmem: protect instobj list with a spinlock
  drm/nouveau/pci: enable c800 magic for some unknown Samsung laptop
  drm/nouveau/pci: enable c800 magic for Clevo P157SM
  drm/radeon: make rv770_set_sw_state failures non-fatal
  drm/amdgpu: move dependency handling out of atomic section v2
  drm/amdgpu: optimize scheduler fence handling
  drm/amdgpu: remove vm->mutex
  drm/amdgpu: add mutex for ba_va->valids/invalids
  drm/amdgpu: adapt vce session create interface changes
  drm/amdgpu: vce use multiple cache surface starting from stoney
  drm/amdgpu: reset vce trap interrupt flag

Pull RTC fixes from Alexandre Belloni:
 "Two fixes for the ds1307 alarm and wakeup"

* tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
  rtc: ds1307: fix alarm reading at probe time
  rtc: ds1307: fix kernel splat due to wakeup irq handling

Pull MIPS fix from Ralf Baechle:
 "Just a fix for empty loops that may be removed by non-antique GCC"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Fix delay loops which may be removed by GCC.

Pull m68k fixes from Geert Uytterhoeven:
 "Summary:

   - Add missing initialization of max_pfn, which is needed to make
     selftests/vm/mlock2-tests succeed,

   - Wire up new mlock2 syscall"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Wire up mlock2
  m68knommu: Add missing initialization of max_pfn and {min,max}_low_pfn
  m68k/mm: sun3 - Add missing initialization of max_pfn and {min,max}_low_pfn
  m68k/mm: m54xx - Add missing initialization of max_pfn
  m68k/mm: motorola - Add missing initialization of max_pfn

Pull ARM fixes from Russell King:
 "Just two changes this time around:

   - wire up the new mlock2 syscall added during the last merge window

   - fix a build problem with certain configurations provoked by making
     CONFIG_OF user selectable"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8454/1: OF implies OF_FLATTREE
  ARM: wire up mlock2 syscall

Pull SCSI target fixes from Nicholas Bellinger:
 - fix tcm-user backend driver expired cmd time processing (agrover)
 - eliminate kref_put_spinlock_irqsave() for I/O completion (bart)
 - fix iscsi login kthread failure case hung task regression (nab)
 - fix COMPARE_AND_WRITE completion use-after-free race (nab)
 - fix COMPARE_AND_WRITE with SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC non zero
   SGL offset data corruption.  (Jan + Doug)
 - fix >= v4.4-rc1 regression for tcm_qla2xxx enable configfs attribute
   (Himanshu + HCH)

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target/stat: print full t10_wwn.model buffer
  target: fix COMPARE_AND_WRITE non zero SGL offset data corruption
  qla2xxx: Fix regression introduced by target configFS changes
  kref: Remove kref_put_spinlock_irqsave()
  target: Invoke release_cmd() callback without holding a spinlock
  target: Fix race for SCF_COMPARE_AND_WRITE_POST checking
  iscsi-target: Fix rx_login_comp hang after login failure
  iscsi-target: return -ENOMEM instead of -1 in case of failed kmalloc()
  target/user: Do not set unused fields in tcmu_ops
  target/user: Fix time calc in expired cmd processing

Pull thermal management fixes from Zhang Rui:
 "Specifics:

 - several fixes and cleanups on Rockchip thermal drivers.

 - add the missing support of RK3368 SoCs in Rockchip driver.

 - small fixes on of-thermal, power_allocator, rcar driver, IMX, and
   QCOM drivers, and also compilation fixes, on thermal.h, when thermal
   is not selected"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  imx: thermal: use CPU temperature grade info for thresholds
  thermal: fix thermal_zone_bind_cooling_device prototype
  Revert "thermal: qcom_spmi: allow compile test"
  thermal: rcar_thermal: remove redundant operation
  thermal: of-thermal: Reduce log level for message when can't fine thermal zone
  thermal: power_allocator: Use temperature reading from tz
  thermal: rockchip: Support the RK3368 SoCs in thermal driver
  thermal: rockchip: consistently use int for temperatures
  thermal: rockchip: Add the sort mode for adc value increment or decrement
  thermal: rockchip: improve the conversion function
  thermal: rockchip: trivial: fix typo in commit
  thermal: rockchip: better to compatible the driver for different SoCs
  dt-bindings: rockchip-thermal: Support the RK3368 SoCs compatible

Cut 'n paste error saw it only process sizeof(t10_wwn.vendor) characters.
Signed-off-by: NDavid Disseldorp <ddiss@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

target_core_sbc's compare_and_write functionality suffers from taking
data at the wrong memory location when writing a CAW request to disk
when a SGL offset is non-zero.

This can happen with loopback and vhost-scsi fabric drivers when
SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC is used to map existing user-space
SGL memory into COMPARE_AND_WRITE READ/WRITE payload buffers.

Given the following sample LIO subtopology,

% targetcli ls /loopback/
o- loopback ................................. [1 Target]
  o- naa.6001405ebb8df14a ....... [naa.60014059143ed2b3]
    o- luns ................................... [2 LUNs]
      o- lun0 ................ [iblock/ram0 (/dev/ram0)]
      o- lun1 ................ [iblock/ram1 (/dev/ram1)]
% lsscsi -g
[3:0:1:0]    disk    LIO-ORG  IBLOCK           4.0   /dev/sdc   /dev/sg3
[3:0:1:1]    disk    LIO-ORG  IBLOCK           4.0   /dev/sdd   /dev/sg4

the following bug can be observed in Linux 4.3 and 4.4~rc1:

% perl -e 'print chr$_ for 0..255,reverse 0..255' >rand
% perl -e 'print "\0" x 512' >zero
% cat rand >/dev/sdd
% sg_compare_and_write -i rand -D zero --lba 0 /dev/sdd
% sg_compare_and_write -i zero -D rand --lba 0 /dev/sdd
Miscompare reported
% hexdump -Cn 512 /dev/sdd
00000000  0f 0e 0d 0c 0b 0a 09 08  07 06 05 04 03 02 01 00
00000010  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00
*
00000200

Rather than writing all-zeroes as instructed with the -D file, it
corrupts the data in the sector by splicing some of the original
bytes in. The page of the first entry of cmd->t_data_sg includes the
CDB, and sg->offset is set to a position past the CDB. I presume that
sg->offset is also the right choice to use for subsequent sglist
members.
Signed-off-by: NJan Engelhardt <jengelh@netitwork.de>
Tested-by: NDouglas Gilbert <dgilbert@interlog.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

this patch fixes following regression

 # targetcli
 [Errno 13] Permission denied: '/sys/kernel/config/target/qla2xxx/21:00:00:0e:1e:08:c7:20/tpgt_1/enable'

Fixes: 2eafd729 ("target: use per-attribute show and store methods")
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The last user is gone. Hence remove this function.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch fixes the following kernel warning because it avoids that
IRQs are disabled while ft_release_cmd() is invoked (fc_seq_set_resp()
invokes spin_unlock_bh()):

WARNING: CPU: 3 PID: 117 at kernel/softirq.c:150 __local_bh_enable_ip+0xaa/0x110()
Call Trace:
 [<ffffffff814f71eb>] dump_stack+0x4f/0x7b
 [<ffffffff8105e56a>] warn_slowpath_common+0x8a/0xc0
 [<ffffffff8105e65a>] warn_slowpath_null+0x1a/0x20
 [<ffffffff81062b2a>] __local_bh_enable_ip+0xaa/0x110
 [<ffffffff814ff229>] _raw_spin_unlock_bh+0x39/0x40
 [<ffffffffa03a7f94>] fc_seq_set_resp+0xe4/0x100 [libfc]
 [<ffffffffa02e604a>] ft_free_cmd+0x4a/0x90 [tcm_fc]
 [<ffffffffa02e6972>] ft_release_cmd+0x12/0x20 [tcm_fc]
 [<ffffffffa042bd66>] target_release_cmd_kref+0x56/0x90 [target_core_mod]
 [<ffffffffa042caf0>] target_put_sess_cmd+0xc0/0x110 [target_core_mod]
 [<ffffffffa042cb81>] transport_release_cmd+0x41/0x70 [target_core_mod]
 [<ffffffffa042d975>] transport_generic_free_cmd+0x35/0x420 [target_core_mod]
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Acked-by: NJoern Engel <joern@logfs.org>
Reviewed-by: NAndy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch addresses a race + use after free where the first
stage of COMPARE_AND_WRITE in compare_and_write_callback()
is rescheduled after the backend sends the secondary WRITE,
resulting in second stage compare_and_write_post() callback
completing in target_complete_ok_work() before the first
can return.

Because current code depends on checking se_cmd->se_cmd_flags
after return from se_cmd->transport_complete_callback(),
this results in first stage having SCF_COMPARE_AND_WRITE_POST
set, which incorrectly falls through into second stage CAW
processing code, eventually triggering a NULL pointer
dereference due to use after free.

To address this bug, pass in a new *post_ret parameter into
se_cmd->transport_complete_callback(), and depend upon this
value instead of ->se_cmd_flags to determine when to return
or fall through into ->queue_status() code for CAW.

Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch addresses a case where iscsi_target_do_tx_login_io()
fails sending the last login response PDU, after the RX/TX
threads have already been started.

The case centers around iscsi_target_rx_thread() not invoking
allow_signal(SIGINT) before the send_sig(SIGINT, ...) occurs
from the failure path, resulting in RX thread hanging
indefinately on iscsi_conn->rx_login_comp.

Note this bug is a regression introduced by:

  commit e5419865
  Author: Nicholas Bellinger <nab@linux-iscsi.org>
  Date:   Wed Jul 22 23:14:19 2015 -0700

      iscsi-target: Fix iscsit_start_kthreads failure OOPs

To address this bug, complete ->rx_login_complete for good
measure in the failure path, and immediately return from
RX thread context if connection state did not actually reach
full feature phase (TARG_CONN_STATE_LOGGED_IN).

Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Smatch complains about returning hard coded error codes, silence this
warning.

drivers/target/iscsi/iscsi_target_parameters.c:211
   iscsi_create_default_params() warn: returning -1 instead of -ENOMEM is sloppy
Signed-off-by: NLuis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

TCMU sets TRANSPORT_FLAG_PASSTHROUGH, so INQUIRY commands will not be
emulated by LIO but passed up to userspace. Therefore TCMU should not
set these, just like pscsi doesn't.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Reversed arguments meant that we were doing nothing for cmds whose deadline
had passed.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

On the ARM architecture, individual platforms select CONFIG_USE_OF if they
need it, but all device tree code is keyed off CONFIG_OF. When building
a platform without DT support and manually enabling CONFIG_OF, we now
get a number of build errors, e.g.

arch/arm/kernel/devtree.c: In function 'setup_machine_fdt':
arch/arm/kernel/devtree.c:215:19: error: implicit declaration of function 'early_init_dt_verify' [-Werror=implicit-function-declaration]

We could now try to separate the use case of booting from DT vs. the
case of using the dynamic implementation, but that seems more complicated
than it can gain us.

This simply changes the ARM Kconfig file to always enable OF_RESERVED_MEM
and OF_EARLY_FLATTREE when CONFIG_OF is enabled. These options add a little
extra code when we just want the dynamic OF implementation, but that seems
like a rather obscure case, and this version solves all CONFIG_OF related
randconfig regressions.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 0166dc11 ("of: make CONFIG_OF user selectable")
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Pull PCI fixes from Bjorn Helgaas:
 "Here are a few fixes I'd like to have in v4.4: a generic one for sysfs
  and three for HiSilicon and DesignWare host controllers.

  Summary:

  NUMA:
   - Prevent out of bounds access in numa_node override (Mathias Krause)

  HiSilicon host bridge driver:
   - Fix deferred probing (Arnd Bergmann)

  Synopsys DesignWare host bridge driver:
   - Remove incorrect io_base assignment (Stanimir Varbanov)
   - Move align_resource function pointer to pci_host_bridge structure
     (Gabriele Paoloni)"

* tag 'pci-v4.4-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  ARM/PCI: Move align_resource function pointer to pci_host_bridge structure
  PCI: hisi: Fix deferred probing
  PCI: designware: Remove incorrect io_base assignment
  PCI: Prevent out of bounds access in numa_node override

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Stable patches:
   - Fix a NFSv4 callback identifier leak that was also causing client
     crashes
   - Fix NFSv4 callback decoding issues when incoming requests are
     truncated
   - Don't declare the attribute cache valid when we call
     nfs_update_inode with an empty attribute structure.
   - Resend LAYOUTGET when there is a race that changes the seqid

  Bugfixes:
   - Fix a number of issues with the NFSv4.2 CLONE ioctl()
   - Properly set NFS v4.2 NFSDBG_FACILITY
   - NFSv4 referrals are broken; Cleanup FATTR4_WORD0_FS_LOCATIONS after
     decoding success
   - Use sliding delay when LAYOUTGET gets NFS4ERR_DELAY
   - Ensure that attrcache is revalidated after a SETATTR"

* tag 'nfs-for-4.4-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  nfs4: resend LAYOUTGET when there is a race that changes the seqid
  nfs: if we have no valid attrs, then don't declare the attribute cache valid
  nfs: ensure that attrcache is revalidated after a SETATTR
  nfs4: limit callback decoding to received bytes
  nfs4: start callback_ident at idr 1
  nfs: use sliding delay when LAYOUTGET gets NFS4ERR_DELAY
  NFS4: Cleanup FATTR4_WORD0_FS_LOCATIONS after decoding success
  NFS: Properly set NFS v4.2 NFSDBG_FACILITY
  nfs: reduce the amount of ifdefs for v4.2 in nfs4file.c
  nfs: use btrfs ioctl defintions for clone
  nfs: allow intra-file CLONE
  nfs: offer native ioctls even if CONFIG_COMPAT is set
  nfs: pass on count for CLONE operations