In mac80211 we always check both scan_req->ie and scan_req->ie_len
against zero before usage, in iwlwifi we should do the same.

Remove not needed "left -= ie_len" while at it.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wl1251 has WLAN_IRQ pin for generating interrupts to host processor,
which is mandatory in SPI mode and optional in SDIO mode (which can
use SDIO interrupts instead). However TI recommends using deditated
IRQ line for SDIO too.

Add support for using dedicated interrupt line with SDIO, but also leave
ability to switch to SDIO interrupts in case it's needed.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Reviewed-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a bunch of endian issues that
were exposed by sparse. It's a miracle that the driver
worked at all till now.

The Lord be praised.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a WMI command has timed out for some reason,
a late WMI response would end up updating the
response region of a new WMI request that has been
issued in the meantime.

Fix this race condition by dropping a WMI response
if a new WMI command has been issued.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no point in trying to set the LED pin
when the module is being unloaded. The target
would be reset anyway.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds macros at certain places
which could be optimized for multiple register writes.

The performance of ath9k_htc improves considerably,
especially reducing the latency involved in a scan run.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Programming the opmode in the HW can be done
before the assoc_id and STA_ID registers are
setup. This helps ath9k_htc when multiple register
writes are used.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for writing multiple registers
in a single USB command.

Specific calls from the HW code that performs multiple
register writes would be modified to make use of this
in subsequent patches.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is required to implement delayed/buffered
register writes in ath9k_htc.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up beacon configuration,
removing a redundant interface type check
and updating beacon interval in the correct place.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add -D__CHECK_ENDIAN__ to driver ccflags so that sparse will
always check endianness by default.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to tests, both TSF lower and upper registers kept counting, so
the higher part could have been updated after the lower part has been
read, as shown in the following log where the upper part is read first
and the lower part next.

tsf = {00000003-fffffffd}
tsf = {00000003-00000001}
tsf = {00000004-0000000b}

This patch corrects this by checking that the upper part has not been
changed while the lower part was read. It has been tested in an IBSS
network where artifical IBSS merges have been done in order to trigger
hundreds of rollover for the TSF lower part.

It follows the logic mentionned by Derek, with only 2 register reads
needed at each additional steps instead of 3 (the minimum number of
register reads is still 3).
Signed-off-by: NBenoit Papillault <benoit.papillault@free.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The first AR9003 hardware family device supported is the
AR9300, which has the vendor:device id 168c:0030
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

LDPC is enabled by the rate control if the its determined
that the target peer supports LDPC. We would have already
intersected the HT capabilities so if our peer supports
LDPC so do we.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

LDPC will be enabled through the rate control algorithm
for each buffer the the tx_info flags.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also add a function to clean up tx status ring.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable CRC check on the descriptor fetched from host on AR9003
upon reseting the TX queue.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also reset tx status ring suring chip reset.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The AR9002 hardware code enables aggregation for WEP but
mac80211 doesn't enable aggregation with WEP, and the AR9003
code family does not need this so skip it for now for AR9003
but leave the code and annotate we should eventually consider
how to remove this in consideration for the HAL unification
goals.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The asynch fifo code is specific to >= AR9287 so stuff it
into the AR9002 hardware family code and skip it for AR9003
cards.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is done depending on what the EEPROM settings indicates.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>