Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Skip IPIP header to get proper layer-4 information.

Like GRE tunnels, this only works if rxhash is not already provided by
the device itself (ethtool -K ethX rxhash off), to allow kernel compute
a software rxhash.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now, when vlan tag on untagged in non-accelerated path is stripped from
skb, headers are reset right away. Benefit from that and avoid calling
__netif_receive_skb recursivelly and just use another_round.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Inspect the payload of PPPOE session messages for the 4 tuples to generate
skb->rxhash.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the 802.1Q packets, if the NIC doesn't support hw-accel-vlan-rx, RPS
won't inspect the internal 4 tuples to generate skb->rxhash, so this kind
of traffic can't get any benefit from RPS.

This patch adds the support for 802.1Q to RPS.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove no longer used operation.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use IFF_UNICAST_FTL to find out if driver handles unicast address
filtering. In case it does not, promisc mode is entered.

Patch also fixes following drivers:
stmmac, niu: support uc filtering and yet it propagated
	ndo_set_multicast_list
bna, benet, pxa168_eth, ks8851, ks8851_mll, ksz884x : has set
	ndo_set_rx_mode but do not support uc filtering
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Crack open GRE packets in __skb_get_rxhash to compute 4-tuple hash on
in encapsulated packet.  Note that this is used only when the
__skb_get_rxhash is taken, in particular only when the device does
not compute provide the rxhash (ie. feature is disabled).

This was tested by creating a single GRE tunnel between two 16 core
AMD machines.  200 netperf TCP_RR streams were ran with 1 byte
request and response size.

Without patch: 157497 tps, 50/90/99% latencies 1250/1292/1364 usecs
With patch: 325896 tps, 50/90/99% latencies 603/848/1169
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Basics for looking for ports in encapsulated packets in tunnels.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The l4_rxhash flag was added to the skb structure to indicate
that the rxhash value was computed over the 4 tuple for the
packet which includes the port information in the encapsulated
transport packet.  This is used by the stack to preserve the
rxhash value in __skb_rx_tunnel.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use some variables for clarity and extensibility.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RCU api had been completed and rcu_access_pointer() or
rcu_dereference_protected() are better than generic
rcu_dereference_raw()
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When assigning a NULL value to an RCU protected pointer, no barrier
is needed. The rcu_assign_pointer, used to handle that but will soon
change to not handle the special case.

Convert all rcu_assign_pointer of NULL value.

//smpl
@@ expression P; @@

- rcu_assign_pointer(P, NULL)
+ RCU_INIT_POINTER(P, NULL)

// </smpl>
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need to use int, its uses are boolean.
May save a few bytes one day.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is not used anywhere except net/core/dev.c now.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vlan_features contains features inherited from underlying device.
NETIF_SOFT_FEATURES are not inherited but belong to the vlan device
itself (ensured in vlan_dev_fix_features()).
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just add GSO to vlan_features initialization, and update comments.

When we set offload features, vlan_dev_fix_features() will do more check.
In vlan_dev_fix_features(), final features is decided by
features of real device and vlan_features of real device.
Signed-off-by: NShan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a change sequence counter to each net namespace
which is bumped whenever a netdevice is added or removed from
the list. If such a change occurred while a link dump took place,
the dump will have the NLM_F_DUMP_INTR flag set in the first
message which has been interrupted and in all subsequent messages
of the same dump.

Note that links may still be modified or renamed while a dump is
taking place but we can guarantee for userspace to receive a
complete list of links and not miss any.

Testing:
I have added 500 VLAN netdevices to make sure the dump is split
over multiple messages. Then while continuously dumping links in
one process I also continuously deleted and re-added a dummy
netdevice in another process. Multiple dumps per seconds have
had the NLM_F_DUMP_INTR flag set.

I guess we can wait for Johannes patch to hit net-next via the
wireless tree.  I just wanted to give this some testing right away.
Signed-off-by: NThomas Graf <tgraf@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are enough instances of this:

    iph->frag_off & htons(IP_MF | IP_OFFSET)

that a helper function is probably warranted.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Testing of VLAN_FLAG_REORDER_HDR does not belong in vlan_untag
but rather in vlan_do_receive.  Otherwise the vlan header
will not be properly put on the packet in the case of
vlan header accelleration.

As we remove the check from vlan_check_reorder_header
rename it vlan_reorder_header to keep the naming clean.

Fix up the skb->pkt_type early so we don't look at the packet
after adding the vlan tag, which guarantees we don't goof
and look at the wrong field.

Use a simple if statement instead of a complicated switch
statement to decided that we need to increment rx_stats
for a multicast packet.

Hopefully at somepoint we will just declare the case where
VLAN_FLAG_REORDER_HDR is cleared as unsupported and remove
the code.  Until then this keeps it working correctly.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Acked-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change is meant to remove all support for displaying an ntuple as
strings via ETHTOOL_GRXNTUPLE.  The reason for this change is due to the
fact that multiple issues have been found including:
 - Multiple buffer overruns for strings being displayed.
 - Incorrect filters displayed, cleared filters with ring of -2 are displayed
 - Setting get_rx_ntuple displays no rules if defined.
 - Endianess wrong on displayed values.
 - Hard limit of 1024 filters makes display functionality extremely limited

The only driver that had supported this interface was ixgbe.  Since it no
longer uses the interface and due to the issues mentioned above I am
submitting this patch to remove it.

v2:
Updated based on comments from Ben Hutchings
 - Left ETH_SS_NTUPLE_FILTERS in code but commented on it being deprecated
 - Removed ethtool_rx_ntuple_list and ethtool_rx_ntuple_flow_spec_container
 - Left ETHTOOL_GRXNTUPLE but commented it as deprecated

Also cleaned up set_rx_ntuple since there is no flow spec container to
maintain we can drop all the code for the alloc and free of it and just
return ops->set_rx_ntuple().
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Frank Blaschka reported :
<quote>
  During heavy network load we turn off/on cpus.
  Sometimes this causes a stall on the network device.
  Digging into the dump I found out following:

  napi is scheduled but does not run. From the I/O buffers
  and the napi state I see napi/rx_softirq processing has stopped
  because the budget was reached. napi stays in the
  softnet_data poll_list and the rx_softirq was raised again.

  I assume at this time the cpu offline comes in,
  the rx softirq is raised/moved to another cpu but napi stays in the
  poll_list of the softnet_data of the now offline cpu.

  Reviewing dev_cpu_callback (net/core/dev.c) I did not find the
  poll_list is transfered to the new cpu.
</quote>

This patch is a straightforward implementation of Frank suggestion :

Transfert poll_list and trigger NET_RX_SOFTIRQ on new cpu.
Reported-by: NFrank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Tested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This interface uses a temporary buffer, but for no real reason.
And now can generate warnings like:

net/sched/sch_generic.c: In function dev_watchdog
net/sched/sch_generic.c:254:10: warning: unused variable drivername

Just return driver->name directly or "".
Reported-by: NConnor Hansen <cmdkhh@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because there is a possibility that skb is kfree_skb()ed and zero cleared
after ndo_start_xmit, we should not see the contents of skb like skb->len and
skb->dev->name after ndo_start_xmit. But trace_net_dev_xmit does that
and causes panic by NULL pointer dereference.
This patch fixes trace_net_dev_xmit not to see the contents of skb directly.

If you want to reproduce this panic,

1. Get tracepoint of net_dev_xmit on
2. Create 2 guests on KVM
2. Make 2 guests use virtio_net
4. Execute netperf from one to another for a long time as a network burden
5. host will panic(It takes about 30 minutes)
Signed-off-by: NKoki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the device passed into dev_disable_lro is a vlan, then repoint the dev
poniter so that we actually modify the underlying physical device.
Signed-of-by: NNeil Horman <nhorman@tuxdriver.com>
CC: davem@davemloft.net
CC: bhutchings@solarflare.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

synchronize_rcu() is very slow in various situations (HZ=100,
CONFIG_NO_HZ=y, CONFIG_PREEMPT=n)

Extract from my (mostly idle) 8 core machine :

 synchronize_rcu() in 99985 us
 synchronize_rcu() in 79982 us
 synchronize_rcu() in 87612 us
 synchronize_rcu() in 79827 us
 synchronize_rcu() in 109860 us
 synchronize_rcu() in 98039 us
 synchronize_rcu() in 89841 us
 synchronize_rcu() in 79842 us
 synchronize_rcu() in 80151 us
 synchronize_rcu() in 119833 us
 synchronize_rcu() in 99858 us
 synchronize_rcu() in 73999 us
 synchronize_rcu() in 79855 us
 synchronize_rcu() in 79853 us

When we hold RTNL mutex, we would like to spend some cpu cycles but not
block too long other processes waiting for this mutex.

We also want to setup/dismantle network features as fast as possible at
boot/shutdown time.

This patch makes synchronize_net() call the expedited version if RTNL is
locked.

synchronize_rcu_expedited() typical delay is about 20 us on my machine.

 synchronize_rcu_expedited() in 18 us
 synchronize_rcu_expedited() in 18 us
 synchronize_rcu_expedited() in 18 us
 synchronize_rcu_expedited() in 18 us
 synchronize_rcu_expedited() in 20 us
 synchronize_rcu_expedited() in 16 us
 synchronize_rcu_expedited() in 20 us
 synchronize_rcu_expedited() in 18 us
 synchronize_rcu_expedited() in 18 us
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
CC: Ben Greear <greearb@candelatech.com>
Reviewed-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the old days, we used to access dev->master in __netif_receive_skb()
in a rcu_read_lock section.

So one synchronize_net() call was needed in netdev_set_master() to make
sure another cpu could not use old master while/after we release it.

We now use netdev_rx_handler infrastructure and added one
synchronize_net() call in bond_release()/bond_release_all()

Remove the obsolete synchronize_net() from netdev_set_master() and add
one in bridge del_nbp() after its netdev_rx_handler_unregister() call.

This makes enslave -d a bit faster.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Jiri Pirko <jpirko@redhat.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When one macvlan device is dismantled, we can avoid one
synchronize_rcu() call done after deletion from hash list, since caller
will perform a synchronize_net() call after its ndo_stop() call.

Add a new netdev->dismantle field to signal this dismantle intent.

Reduces RTNL hold time.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Ben Greear <greearb@candelatech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cool, how about we make 'Features changed' debug as well?
This way userspace can't fill up the log just by tweaking tun features
with an ioctl.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using plain hlist_del() in dev_change_name() is wrong since a
concurrent reader can crash trying to dereference LIST_POISON1.

Bug introduced in commit 72c9528b (net: Introduce
dev_get_by_name_rcu())
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Those reduced to DEBUG can possibly be triggered by unprivileged processes
and are nothing exceptional. Illegal checksum combinations can only be
caused by driver bug, so promote those messages to WARN.

Since GSO without SG will now only cause DEBUG message from
netdev_fix_features(), remove the workaround from register_netdevice().
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 1c5cae81 (net: call dev_alloc_name from register_netdevice),
a bug of bonding was involved, see example 1 and 2.

In register_netdevice(), the name of net_device is not valid until
dev_get_valid_name() is called. But dev->netdev_ops->ndo_init(that is
bond_init) is called before dev_get_valid_name(),
and it uses the invalid name of net_device.

I think register_netdevice() should make sure that the name of net_device is
valid before calling ndo_init().

example 1:
modprobe bonding
ls  /proc/net/bonding/bond%d

ps -eLf
root      3398     2  3398  0    1 21:34 ?        00:00:00 [bond%d]

example 2:
modprobe bonding max_bonds=3

[  170.100292] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[  170.101090] bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details.
[  170.102469] ------------[ cut here ]------------
[  170.103150] WARNING: at /home/pwp/net-next-2.6/fs/proc/generic.c:586 proc_register+0x126/0x157()
[  170.104075] Hardware name: VirtualBox
[  170.105065] proc_dir_entry 'bonding/bond%d' already registered
[  170.105613] Modules linked in: bonding(+) sunrpc ipv6 uinput microcode ppdev parport_pc parport joydev e1000 pcspkr i2c_piix4 i2c_core [last unloaded: bonding]
[  170.108397] Pid: 3457, comm: modprobe Not tainted 2.6.39-rc2+ #14
[  170.108935] Call Trace:
[  170.109382]  [<c0438f3b>] warn_slowpath_common+0x6a/0x7f
[  170.109911]  [<c051a42a>] ? proc_register+0x126/0x157
[  170.110329]  [<c0438fc3>] warn_slowpath_fmt+0x2b/0x2f
[  170.110846]  [<c051a42a>] proc_register+0x126/0x157
[  170.111870]  [<c051a4dd>] proc_create_data+0x82/0x98
[  170.112335]  [<f94e6af6>] bond_create_proc_entry+0x3f/0x73 [bonding]
[  170.112905]  [<f94dd806>] bond_init+0x77/0xa5 [bonding]
[  170.113319]  [<c0721ac6>] register_netdevice+0x8c/0x1d3
[  170.113848]  [<f94e0e30>] bond_create+0x6c/0x90 [bonding]
[  170.114322]  [<f94f4763>] bonding_init+0x763/0x7b1 [bonding]
[  170.114879]  [<c0401240>] do_one_initcall+0x76/0x122
[  170.115317]  [<f94f4000>] ? 0xf94f3fff
[  170.115799]  [<c0463f1e>] sys_init_module+0x1286/0x140d
[  170.116879]  [<c07c6d9f>] sysenter_do_call+0x12/0x28
[  170.117404] ---[ end trace 64e4fac3ae5fff1a ]---
[  170.117924] bond%d: Warning: failed to register to debugfs
[  170.128728] ------------[ cut here ]------------
[  170.129360] WARNING: at /home/pwp/net-next-2.6/fs/proc/generic.c:586 proc_register+0x126/0x157()
[  170.130323] Hardware name: VirtualBox
[  170.130797] proc_dir_entry 'bonding/bond%d' already registered
[  170.131315] Modules linked in: bonding(+) sunrpc ipv6 uinput microcode ppdev parport_pc parport joydev e1000 pcspkr i2c_piix4 i2c_core [last unloaded: bonding]
[  170.133731] Pid: 3457, comm: modprobe Tainted: G        W   2.6.39-rc2+ #14
[  170.134308] Call Trace:
[  170.134743]  [<c0438f3b>] warn_slowpath_common+0x6a/0x7f
[  170.135305]  [<c051a42a>] ? proc_register+0x126/0x157
[  170.135820]  [<c0438fc3>] warn_slowpath_fmt+0x2b/0x2f
[  170.137168]  [<c051a42a>] proc_register+0x126/0x157
[  170.137700]  [<c051a4dd>] proc_create_data+0x82/0x98
[  170.138174]  [<f94e6af6>] bond_create_proc_entry+0x3f/0x73 [bonding]
[  170.138745]  [<f94dd806>] bond_init+0x77/0xa5 [bonding]
[  170.139278]  [<c0721ac6>] register_netdevice+0x8c/0x1d3
[  170.139828]  [<f94e0e30>] bond_create+0x6c/0x90 [bonding]
[  170.140361]  [<f94f4763>] bonding_init+0x763/0x7b1 [bonding]
[  170.140927]  [<c0401240>] do_one_initcall+0x76/0x122
[  170.141494]  [<f94f4000>] ? 0xf94f3fff
[  170.141975]  [<c0463f1e>] sys_init_module+0x1286/0x140d
[  170.142463]  [<c07c6d9f>] sysenter_do_call+0x12/0x28
[  170.142974] ---[ end trace 64e4fac3ae5fff1b ]---
[  170.144949] bond%d: Warning: failed to register to debugfs
Signed-off-by: NWeiping Pan <panweiping3@gmail.com>
Reviewed-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It will be needed by bonding and other drivers changing vlan_features
after ndo_init callback.

As a bonus, this includes kernel-doc for netdev_update_features().
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 44345724 (factorize sync-rcu call in
unregister_netdevice_many) mistakenly removed one test from dev_close()

Following actions trigger a BUG :

modprobe bonding
modprobe dummy
ifconfig bond0 up
ifenslave bond0 dummy0
rmmod dummy

dev_close() must not close a non IFF_UP device.

With help from Frank Blaschka and Einar EL Lueck
Reported-by: NFrank Blaschka <blaschka@linux.vnet.ibm.com>
Reported-by: NEinar EL Lueck <ELELUECK@de.ibm.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Force dev_alloc_name() to be called from register_netdevice() by
dev_get_valid_name(). That allows to remove multiple explicit
dev_alloc_name() calls.

The possibility to call dev_alloc_name in advance remains.

This also fixes veth creation regresion caused by
84c49d8cSigned-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ioctl() calls against a socket with an inappropriate ioctl operation
are incorrectly returning EINVAL rather than ENOTTY:

  [ENOTTY]
      Inappropriate I/O control operation.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=33992Signed-off-by: NLifeng Sun <lifongsun@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).

This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.

All drivers visible to make allyesconfig under x86_64 have been
updated.
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify and fix netdev_increment_features() to conform to what is
stated in netdevice.h comments about NETIF_F_ONE_FOR_ALL.
Include FCoE segmentation and VLAN-challedged flags in computation.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since now when bonding uses rx_handler, all traffic going into bond
device goes thru bond_handle_frame. So there's no need to go back into
bonding code later via ptype handlers. This patch converts
original ptype handlers into "bonding receive probes". These functions
are called from bond_handle_frame and they are registered per-mode.

Note that vlan packets are also handled because they are always untagged
thanks to vlan_untag()

Note that this also allows arpmon for eth-bond-bridge-vlan topology.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>