Add support for an external 26 MHz crystal source.

[Changed wl->ref_clock to priv->ref_clock -- Luca.]
Signed-off-by: NGrant Erickson <marathon96@gmail.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In PG2 only the last frame in the aggregate buffer should be
aligned to the sdio block size. This frame's header msb should be
set to 0, while in all the previous frames in the aggregation
buffer, this bit should be set to 1.

[Add a HW op for setting the frame ctrl bit only for 18xx. Other minor
cleanups - Arik]

[Make the pre_pkt_send operation optional -- Luca]
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In PG2, the HW watchdog interrupt occupies bit0 of the event vector, and
the SW watchdog is relocated to bit9. We perform the relocation
globally, as there's only one watchdog bit on previous platforms (bit0).

[Only mask in the new bit9 for platforms supporting it. This avoids
spurious events on other platforms - Arik]
Signed-off-by: NOrit Brayer <orit@ti.com>
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

PG2 requires 4 new parameters that to be passed to the PHY.

Use the actual PHY initialization struct size for the mem size of the
PHY_INIT section, to account for additions in params.

[Make sure PG1 still gets the original struct - Arik]
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

PG2 has a unique chip id. It supports similar HW quirks.
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

was hardcoded 252, now uses the parameters struct size.
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Introduce “pactive” scan mode – which instructs the fw to
perform a passive scan until an activity/energy is detected
on these channels, once energy detected the channel becomes
active.
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

When comparing 2 ssids the ssid_len must be taken
into account. Otherwise, a substring will be treated
as equal.

This bug might cause ssids to get scanned as
public ssids (rather than hidden), resulting in
broadcast probe request (instead of ssid-specific
ones)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Due to a need by the firmware when working in multirole
the role id needs to be added to the structs of the
following commands:
CMD_CONNECTION_SCAN_CFG, CMD_CONNECTION_SCAN_SSID_CFG,
CMD_START_PERIODIC_SCAN, CMD_STOP_PERIODIC_SCAN
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We have to reconfigure the fw when erp protection should
be enabled/disabled. Pass beacons containing changes
in the ERP protection IE, so we could analyze them.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Send beacon loss events to userspace, so it will be
able to initiate roaming before disconnection
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

If the driver received a watchdog interrupt then the
assumption is that the fw is hanged. Avoid sending
the stop fwlog command in case of a watchdog recovey
to avoid waiting for the 2 seconds timeout of the command.
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The 12xx set_key just calls the common wlcore_set_key function, in order
to program the keys into the FW.

The 18xx variant changes the spare block count when a GEM or TKIP
key is set. Also modify the get_spare_blocks HW op for 18xx to return
the correct numbers of spare blocks, according to what is currently
set in FW.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Stop network queues during Tx flush, and also drop other internal
mac80211 packets (mgmt) that may arrive when the queues are stopped.

When flush is done all driver queues are clear, forcefully if needed.

Protect the Tx flush operation with a new mutex, to prevent concurrency
that can mess us queue state.

Based on a patch by Eliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Allow the driver to wake/stop the queues for multiple reasons. A queue
is started when no stop-reasons exist.

Convert all wake/stop queue calls to use the new API.

Before, a stopped queue was almost synonymous a high-watermark on Tx.
Remove a bit of code in wl12xx_tx_reset() that relied on it.

Internal packets arriving from mac80211 are also discarded when a queue
is stopped. A notable exception to this is the watermark reason, which
is a "soft"-stop reason. We allow traffic to gradually come to a halt,
but we don't mind spurious packets here and there. This is merely a flow
regulation mechanism.

Based on a similar patch by Eliad Peller <eliadWizery.com>.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add a HW op for getting spare blocks.

12xx cards require 2 spare blocks for GEM encrypted SKBs, regardless
of VIFs or keys programmed into the FW.

18xx cards require 2 spare blocks when there are any connected TKIP or
GEM VIFs. For now always return 2 spare blocks, as this works with all
networks. The special case TKIP/GEM functionality is added at a later
patch.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

18xx chips do not require extra space in the TKIP header. Introduce a
new HW quirk to allow us to make this feature arch-specific. 12xx chip
will now have this quirk.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In some multi role scenarios the driver might send multi
roc requests without sending a croc first, the fw queues
those requests and starts service the next roc request as
soon as the driver sends a croc for the previous one. So,
if the fw rocs on channel X and driver asks to roc also
on channel Y, the fw will not start service Y (and will
not send roc complete event for this request) until the
driver releases the fw with croc X.
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The beacon early termination is not relevant for
high basic rates, which doesn't contribute
anything to the PS and only adds unnecessary FW
work.

Enable BET only if the basic rate is less than 9
Mbps.
Signed-off-by: NZiv Riesel <zivriesel@ti.com>
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Wrong fm_coex parameters were set during wl18xx
init phase, fix it.
Signed-off-by: NZiv Riesel <zivriesel@ti.com>
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Wrong fm_coex parameters were set during wl12xx
init phase, fix it.
Signed-off-by: NZiv Riesel <zivriesel@ti.com>
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This BUG_ON also ignored the INTENDED_FW_RECOVERY flag. This would
result in a BUG() when using the bug_on_recovery module parameter during
multi-role.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In some cases, the ROC_COMPLETE event might exceed the
current timeout (750 msec). Increase it to 1 sec.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

On CHANGE_CHANNEL indication, we should flush all the
queued tx frames, so they will be sent on the correct
(current) channel.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In the enum conf_tx_ac CONF_TX_AC_ANY_TID should
be 0xff to match the firmware's implementation.
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The polarity should be set before the firmware is loaded
since the firmware touches the same register. Access
of the firmware and driver to the same register will
cause a collision since there is no exclusion scheme.
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In ieee80211.h the uapsd bit mask is defined such that
VO=BIT(0), VI=BIT(1), BK=BIT(2), BE=BIT(3).
The firmware uses the indexing as defined in the ieee80211
spec, meaning that VO=3, VI=2, BK=1, BE=0.

In AP mode when adding peer wlcore needs to convert
the indexing accordingly.
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Save the ht_cap IE per-band, so we can configure different
params to BG and A bands (we currently don't support MIMO
on A band)

[Small fix for rx_highest - Arik]
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add a dependency on mac80211 in Kconfig, and also replace some spaces
with tabs.
Reported-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

With the new FW (sigle role X.3.8.0.108, multi role X.5.4.0.21)
we are supporting 3 RX BA sessions, this change is to support this
new ability.
Signed-off-by: NAssaf Azulay <assaf@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Modify default parameters to reduce firmware BSS lose
probability in congested environment.

[Applied to 18xx configuration as well - Arik]
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Make sure the deauth bcast gets sent

[Make sure we are AP as well before the flush - Arik]
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Multicast management frames (e.g. global deauth)
should be sent out on the bcast link, rather than
the global, which should be used only for pre-added
stations (e.g. for auth/assoc resp).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We can't use cancel_delayed_work_sync() from functions that take the
wl->mutex, since connection_loss_work also takes the mutex. This might
result in a deadlock. Restructure the code so the work is synchronously
canceled before taking the mutex.
Avoid a bug where we would indefinitely delay the connection loss
indication by re-queuing the connection loss work on consecutive beacon
loss events.

Cc: bartosz.markowski <bartosz.markowski@tieto.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In patch d7b63b9f we have raised the dynamic
PS timeout to 200ms to improve user experience. Re-apply the change,
since it was reverted in the wlcore split.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The dynamic PS timeout is meaningless in forced PS mode.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The "static" modifier was mistakenly forgotten for some functions.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Commit 4afc37 (wlcore: reorder identify_chip and get_hw_info) broke
support for wl127x chips.

When we moved the identify_chip operation to an earlier stage (ie. to
the probe function), we broke wl127x support because during HW init we
would set the WLCORE_QUIRK_TX_BLOCKSIZE_ALIGN.

To avoid this, set this quirk in the identify_chip operations and only
force it to be unset if the bus module doesn't support it.  We were
doing the opposite and setting the flag if the bus module supports it.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

as tcp check sum is going to be removed from firmware, and as
there is a problem with getting dns in security when checksum is
enabled, it was decided to disable it by default.
for none security modes it can be enabled by module paramenter.
Signed-off-by: NAssaf Azulay <assaf@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Some of the structures were updated, other structures had a few
missing values and a few new ones were added.  Change the driver
structs accordingly.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>