- 27 4月, 2008 1 次提交
-
-
由 Yinghai Lu 提交于
vmemmap allocation currently has this layout: [ffffe20000000000-ffffe200001fffff] PMD ->ffff810001400000 on node 0 [ffffe20000200000-ffffe200003fffff] PMD ->ffff810001800000 on node 0 [ffffe20000400000-ffffe200005fffff] PMD ->ffff810001c00000 on node 0 [ffffe20000600000-ffffe200007fffff] PMD ->ffff810002000000 on node 0 [ffffe20000800000-ffffe200009fffff] PMD ->ffff810002400000 on node 0 ... note that there is a 2M hole between them - not optimal. the root cause is that usemap (24 bytes) will be allocated after every 2M mem_map, and it will push next vmemmap (2M) to the next (2M) alignment. solution: try to allocate the mem_map continously. after the patch, we get: [ffffe20000000000-ffffe200001fffff] PMD ->ffff810001400000 on node 0 [ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0 [ffffe20000400000-ffffe200005fffff] PMD ->ffff810001800000 on node 0 [ffffe20000600000-ffffe200007fffff] PMD ->ffff810001a00000 on node 0 [ffffe20000800000-ffffe200009fffff] PMD ->ffff810001c00000 on node 0 ... which is the ideal layout. and usemap will share a page because of they are allocated continuously too: sparse_early_usemap_alloc: usemap = ffff810024e00000 size = 24 sparse_early_usemap_alloc: usemap = ffff810024e00080 size = 24 sparse_early_usemap_alloc: usemap = ffff810024e00100 size = 24 sparse_early_usemap_alloc: usemap = ffff810024e00180 size = 24 ... so we make the bootmem allocation more compact and use less memory for usemap => mission accomplished ;-) Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com> Signed-off-by: NIngo Molnar <mingo@elte.hu>
-
- 16 4月, 2008 1 次提交
-
-
由 Ingo Molnar 提交于
Fix memory corruption and crash on 32-bit x86 systems. If a !PAE x86 kernel is booted on a 32-bit system with more than 4GB of RAM, then we call memory_present() with a start/end that goes outside the scope of MAX_PHYSMEM_BITS. That causes this loop to happily walk over the limit of the sparse memory section map: for (pfn = start; pfn < end; pfn += PAGES_PER_SECTION) { unsigned long section = pfn_to_section_nr(pfn); struct mem_section *ms; sparse_index_init(section, nid); set_section_nid(section, nid); ms = __nr_to_section(section); if (!ms->section_mem_map) ms->section_mem_map = sparse_encode_early_nid(nid) | SECTION_MARKED_PRESENT; 'ms' will be out of bounds and we'll corrupt a small amount of memory by encoding the node ID and writing SECTION_MARKED_PRESENT (==0x1) over it. The corruption might happen when encoding a non-zero node ID, or due to the SECTION_MARKED_PRESENT which is 0x1: mmzone.h:#define SECTION_MARKED_PRESENT (1UL<<0) The fix is to sanity check anything the architecture passes to sparsemem. This bug seems to be rather old (as old as sparsemem support itself), but the exact incarnation depended on random details like configs, which made this bug more prominent in v2.6.25-to-be. An additional enhancement might be to print a warning about ignored or trimmed memory ranges. Signed-off-by: NIngo Molnar <mingo@elte.hu> Tested-by: NChristoph Lameter <clameter@sgi.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Nick Piggin <npiggin@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Yinghai Lu <Yinghai.Lu@sun.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 06 2月, 2008 2 次提交
-
-
由 Sam Ravnborg 提交于
Fix following warning: WARNING: mm/built-in.o(.text+0x22069): Section mismatch in reference from the function sparse_early_usemap_alloc() to the function .init.text:__alloc_bootmem_node() static sparse_early_usemap_alloc() were used only by sparse_init() and with sparse_init() annotated _init it is safe to annotate sparse_early_usemap_alloc with __init too. Signed-off-by: NSam Ravnborg <sam@ravnborg.org> Cc: Andy Whitcroft <apw@shadowen.org> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Christoph Lameter <clameter@sgi.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Christoph Lameter 提交于
Checking if an address is a vmalloc address is done in a couple of places. Define a common version in mm.h and replace the other checks. Again the include structures suck. The definition of VMALLOC_START and VMALLOC_END is not available in vmalloc.h since highmem.c cannot be included there. Signed-off-by: NChristoph Lameter <clameter@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 18 12月, 2007 2 次提交
-
-
由 WANG Cong 提交于
Improve the error handling for mm/sparse.c::sparse_add_one_section(). And I see no reason to check 'usemap' until holding the 'pgdat_resize_lock'. [geoffrey.levand@am.sony.com: sparse_index_init() returns -EEXIST] Cc: Christoph Lameter <clameter@sgi.com> Acked-by: NDave Hansen <haveblue@us.ibm.com> Cc: Rik van Riel <riel@redhat.com> Acked-by: NYasunori Goto <y-goto@jp.fujitsu.com> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: NWANG Cong <xiyou.wangcong@gmail.com> Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 WANG Cong 提交于
Since sparse_index_alloc() can return NULL on memory allocation failure, we must deal with the failure condition when calling it. Signed-off-by: NWANG Cong <xiyou.wangcong@gmail.com> Cc: Christoph Lameter <clameter@sgi.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 30 10月, 2007 1 次提交
-
-
由 Linus Torvalds 提交于
This reverts commit 2e1c49db. First off, testing in Fedora has shown it to cause boot failures, bisected down by Martin Ebourne, and reported by Dave Jobes. So the commit will likely be reverted in the 2.6.23 stable kernels. Secondly, in the 2.6.24 model, x86-64 has now grown support for SPARSEMEM_VMEMMAP, which disables the relevant code anyway, so while the bug is not visible any more, it's become invisible due to the code just being irrelevant and no longer enabled on the only architecture that this ever affected. Reported-by: NDave Jones <davej@redhat.com> Tested-by: NMartin Ebourne <fedora@ebourne.me.uk> Cc: Zou Nan hai <nanhai.zou@intel.com> Cc: Suresh Siddha <suresh.b.siddha@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Acked-by: NAndy Whitcroft <apw@shadowen.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 17 10月, 2007 5 次提交
-
-
由 Yasunori Goto 提交于
This patch is to avoid panic when memory hot-add is executed with sparsemem-vmemmap. Current vmemmap-sparsemem code doesn't support memory hot-add. Vmemmap must be populated when hot-add. This is for 2.6.23-rc2-mm2. Todo: # Even if this patch is applied, the message "[xxxx-xxxx] potential offnode page_structs" is displayed. To allocate memmap on its node, memmap (and pgdat) must be initialized itself like chicken and egg relationship. # vmemmap_unpopulate will be necessary for followings. - For cancel hot-add due to error. - For unplug. Signed-off-by: NYasunori Goto <y-goto@jp.fujitsu.com> Cc: Andy Whitcroft <apw@shadowen.org> Cc: Christoph Lameter <clameter@sgi.com> Cc: Mel Gorman <mel@csn.ul.ie> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Mel Gorman 提交于
There are problems in the use of SPARSEMEM and pageblock flags that causes problems on ia64. The first part of the problem is that units are incorrect in SECTION_BLOCKFLAGS_BITS computation. This results in a map_section's section_mem_map being treated as part of a bitmap which isn't good. This was evident with an invalid virtual address when mem_init attempted to free bootmem pages while relinquishing control from the bootmem allocator. The second part of the problem occurs because the pageblock flags bitmap is be located with the mem_section. The SECTIONS_PER_ROOT computation using sizeof (mem_section) may not be a power of 2 depending on the size of the bitmap. This renders masks and other such things not power of 2 base. This issue was seen with SPARSEMEM_EXTREME on ia64. This patch moves the bitmap outside of mem_section and uses a pointer instead in the mem_section. The bitmaps are allocated when the section is being initialised. Note that sparse_early_usemap_alloc() does not use alloc_remap() like sparse_early_mem_map_alloc(). The allocation required for the bitmap on x86, the only architecture that uses alloc_remap is typically smaller than a cache line. alloc_remap() pads out allocations to the cache size which would be a needless waste. Credit to Bob Picco for identifying the original problem and effecting a fix for the SECTION_BLOCKFLAGS_BITS calculation. Credit to Andy Whitcroft for devising the best way of allocating the bitmaps only when required for the section. [wli@holomorphy.com: warning fix] Signed-off-by: NBob Picco <bob.picco@hp.com> Signed-off-by: NAndy Whitcroft <apw@shadowen.org> Signed-off-by: NMel Gorman <mel@csn.ul.ie> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: NWilliam Irwin <bill.irwin@oracle.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Christoph Lameter 提交于
SPARSEMEM is a pretty nice framework that unifies quite a bit of code over all the arches. It would be great if it could be the default so that we can get rid of various forms of DISCONTIG and other variations on memory maps. So far what has hindered this are the additional lookups that SPARSEMEM introduces for virt_to_page and page_address. This goes so far that the code to do this has to be kept in a separate function and cannot be used inline. This patch introduces a virtual memmap mode for SPARSEMEM, in which the memmap is mapped into a virtually contigious area, only the active sections are physically backed. This allows virt_to_page page_address and cohorts become simple shift/add operations. No page flag fields, no table lookups, nothing involving memory is required. The two key operations pfn_to_page and page_to_page become: #define __pfn_to_page(pfn) (vmemmap + (pfn)) #define __page_to_pfn(page) ((page) - vmemmap) By having a virtual mapping for the memmap we allow simple access without wasting physical memory. As kernel memory is typically already mapped 1:1 this introduces no additional overhead. The virtual mapping must be big enough to allow a struct page to be allocated and mapped for all valid physical pages. This vill make a virtual memmap difficult to use on 32 bit platforms that support 36 address bits. However, if there is enough virtual space available and the arch already maps its 1-1 kernel space using TLBs (f.e. true of IA64 and x86_64) then this technique makes SPARSEMEM lookups even more efficient than CONFIG_FLATMEM. FLATMEM needs to read the contents of the mem_map variable to get the start of the memmap and then add the offset to the required entry. vmemmap is a constant to which we can simply add the offset. This patch has the potential to allow us to make SPARSMEM the default (and even the only) option for most systems. It should be optimal on UP, SMP and NUMA on most platforms. Then we may even be able to remove the other memory models: FLATMEM, DISCONTIG etc. [apw@shadowen.org: config cleanups, resplit code etc] [kamezawa.hiroyu@jp.fujitsu.com: Fix sparsemem_vmemmap init] [apw@shadowen.org: vmemmap: remove excess debugging] [apw@shadowen.org: simplify initialisation code and reduce duplication] [apw@shadowen.org: pull out the vmemmap code into its own file] Signed-off-by: NChristoph Lameter <clameter@sgi.com> Signed-off-by: NAndy Whitcroft <apw@shadowen.org> Acked-by: NMel Gorman <mel@csn.ul.ie> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Andi Kleen <ak@suse.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Andy Whitcroft 提交于
We have flags to indicate whether a section actually has a valid mem_map associated with it. This is never set and we rely solely on the present bit to indicate a section is valid. By definition a section is not valid if it has no mem_map and there is a window during init where the present bit is set but there is no mem_map, during which pfn_valid() will return true incorrectly. Use the existing SECTION_HAS_MEM_MAP flag to indicate the presence of a valid mem_map. Switch valid_section{,_nr} and pfn_valid() to this bit. Add a new present_section{,_nr} and pfn_present() interfaces for those users who care to know that a section is going to be valid. [akpm@linux-foundation.org: coding-syle fixes] Signed-off-by: NAndy Whitcroft <apw@shadowen.org> Acked-by: NMel Gorman <mel@csn.ul.ie> Cc: Christoph Lameter <clameter@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Andi Kleen <ak@suse.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Andy Whitcroft 提交于
SPARSEMEM is a pretty nice framework that unifies quite a bit of code over all the arches. It would be great if it could be the default so that we can get rid of various forms of DISCONTIG and other variations on memory maps. So far what has hindered this are the additional lookups that SPARSEMEM introduces for virt_to_page and page_address. This goes so far that the code to do this has to be kept in a separate function and cannot be used inline. This patch introduces a virtual memmap mode for SPARSEMEM, in which the memmap is mapped into a virtually contigious area, only the active sections are physically backed. This allows virt_to_page page_address and cohorts become simple shift/add operations. No page flag fields, no table lookups, nothing involving memory is required. The two key operations pfn_to_page and page_to_page become: #define __pfn_to_page(pfn) (vmemmap + (pfn)) #define __page_to_pfn(page) ((page) - vmemmap) By having a virtual mapping for the memmap we allow simple access without wasting physical memory. As kernel memory is typically already mapped 1:1 this introduces no additional overhead. The virtual mapping must be big enough to allow a struct page to be allocated and mapped for all valid physical pages. This vill make a virtual memmap difficult to use on 32 bit platforms that support 36 address bits. However, if there is enough virtual space available and the arch already maps its 1-1 kernel space using TLBs (f.e. true of IA64 and x86_64) then this technique makes SPARSEMEM lookups even more efficient than CONFIG_FLATMEM. FLATMEM needs to read the contents of the mem_map variable to get the start of the memmap and then add the offset to the required entry. vmemmap is a constant to which we can simply add the offset. This patch has the potential to allow us to make SPARSMEM the default (and even the only) option for most systems. It should be optimal on UP, SMP and NUMA on most platforms. Then we may even be able to remove the other memory models: FLATMEM, DISCONTIG etc. The current aim is to bring a common virtually mapped mem_map to all architectures. This should facilitate the removal of the bespoke implementations from the architectures. This also brings performance improvements for most architecture making sparsmem vmemmap the more desirable memory model. The ultimate aim of this work is to expand sparsemem support to encompass all the features of the other memory models. This could allow us to drop support for and remove the other models in the longer term. Below are some comparitive kernbench numbers for various architectures, comparing default memory model against SPARSEMEM VMEMMAP. All but ia64 show marginal improvement; we expect the ia64 figures to be sorted out when the larger mapping support returns. x86-64 non-NUMA Base VMEMAP % change (-ve good) User 85.07 84.84 -0.26 System 34.32 33.84 -1.39 Total 119.38 118.68 -0.59 ia64 Base VMEMAP % change (-ve good) User 1016.41 1016.93 0.05 System 50.83 51.02 0.36 Total 1067.25 1067.95 0.07 x86-64 NUMA Base VMEMAP % change (-ve good) User 30.77 431.73 0.22 System 45.39 43.98 -3.11 Total 476.17 475.71 -0.10 ppc64 Base VMEMAP % change (-ve good) User 488.77 488.35 -0.09 System 56.92 56.37 -0.97 Total 545.69 544.72 -0.18 Below are some AIM bencharks on IA64 and x86-64 (thank Bob). The seems pretty much flat as you would expect. ia64 results 2 cpu non-numa 4Gb SCSI disk Benchmark Version Machine Run Date AIM Multiuser Benchmark - Suite VII "1.1" extreme Jun 1 07:17:24 2007 Tasks Jobs/Min JTI Real CPU Jobs/sec/task 1 98.9 100 58.9 1.3 1.6482 101 5547.1 95 106.0 79.4 0.9154 201 6377.7 95 183.4 158.3 0.5288 301 6932.2 95 252.7 237.3 0.3838 401 7075.8 93 329.8 316.7 0.2941 501 7235.6 94 403.0 396.2 0.2407 600 7387.5 94 472.7 475.0 0.2052 Benchmark Version Machine Run Date AIM Multiuser Benchmark - Suite VII "1.1" vmemmap Jun 1 09:59:04 2007 Tasks Jobs/Min JTI Real CPU Jobs/sec/task 1 99.1 100 58.8 1.2 1.6509 101 5480.9 95 107.2 79.2 0.9044 201 6490.3 95 180.2 157.8 0.5382 301 6886.6 94 254.4 236.8 0.3813 401 7078.2 94 329.7 316.0 0.2942 501 7250.3 95 402.2 395.4 0.2412 600 7399.1 94 471.9 473.9 0.2055 open power 710 2 cpu, 4 Gb, SCSI and configured physically Benchmark Version Machine Run Date AIM Multiuser Benchmark - Suite VII "1.1" extreme May 29 15:42:53 2007 Tasks Jobs/Min JTI Real CPU Jobs/sec/task 1 25.7 100 226.3 4.3 0.4286 101 1096.0 97 536.4 199.8 0.1809 201 1236.4 96 946.1 389.1 0.1025 301 1280.5 96 1368.0 582.3 0.0709 401 1270.2 95 1837.4 771.0 0.0528 501 1251.4 96 2330.1 955.9 0.0416 601 1252.6 96 2792.4 1139.2 0.0347 701 1245.2 96 3276.5 1334.6 0.0296 918 1229.5 96 4345.4 1728.7 0.0223 Benchmark Version Machine Run Date AIM Multiuser Benchmark - Suite VII "1.1" vmemmap May 30 07:28:26 2007 Tasks Jobs/Min JTI Real CPU Jobs/sec/task 1 25.6 100 226.9 4.3 0.4275 101 1049.3 97 560.2 198.1 0.1731 201 1199.1 97 975.6 390.7 0.0994 301 1261.7 96 1388.5 591.5 0.0699 401 1256.1 96 1858.1 771.9 0.0522 501 1220.1 96 2389.7 955.3 0.0406 601 1224.6 96 2856.3 1133.4 0.0340 701 1252.0 96 3258.7 1314.1 0.0298 915 1232.8 96 4319.7 1704.0 0.0225 amd64 2 2-core, 4Gb and SATA Benchmark Version Machine Run Date AIM Multiuser Benchmark - Suite VII "1.1" extreme Jun 2 03:59:48 2007 Tasks Jobs/Min JTI Real CPU Jobs/sec/task 1 13.0 100 446.4 2.1 0.2173 101 533.4 97 1102.0 110.2 0.0880 201 578.3 97 2022.8 220.8 0.0480 301 583.8 97 3000.6 332.3 0.0323 401 580.5 97 4020.1 442.2 0.0241 501 574.8 98 5072.8 558.8 0.0191 600 566.5 98 6163.8 671.0 0.0157 Benchmark Version Machine Run Date AIM Multiuser Benchmark - Suite VII "1.1" vmemmap Jun 3 04:19:31 2007 Tasks Jobs/Min JTI Real CPU Jobs/sec/task 1 13.0 100 447.8 2.0 0.2166 101 536.5 97 1095.6 109.7 0.0885 201 567.7 97 2060.5 219.3 0.0471 301 582.1 96 3009.4 330.2 0.0322 401 578.2 96 4036.4 442.4 0.0240 501 585.1 98 4983.2 555.1 0.0195 600 565.5 98 6175.2 660.6 0.0157 This patch: Fix some spelling errors. Signed-off-by: NChristoph Lameter <clameter@sgi.com> Signed-off-by: NAndy Whitcroft <apw@shadowen.org> Acked-by: NMel Gorman <mel@csn.ul.ie> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Andi Kleen <ak@suse.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 23 8月, 2007 1 次提交
-
-
由 Andy Whitcroft 提交于
Booting SPARSEMEM on NUMA systems trips a BUG in page_alloc.c: Initializing HighMem for node 0 (00038000:00100000) Initializing HighMem for node 1 (00100000:001ffe00) ------------[ cut here ]------------ kernel BUG at /home/apw/git/linux-2.6/mm/page_alloc.c:456! [...] This occurs because the section to node id mapping is not being setup correctly during init under SPARSEMEM_STATIC, leading to an attempt to free pages from all nodes into the zones on node 0. When the zone_table[] was removed in the following commit, a new section to node mapping table was introduced: commit 89689ae7 [PATCH] Get rid of zone_table[] That conversion inadvertantly only initialised the node mapping in SPARSEMEM_EXTREME. Ensure we initialise the node mapping in SPARSEMEM_STATIC. [akpm@linux-foundation.org: make the stubs static inline] Signed-off-by: NAndy Whitcroft <apw@shadowen.org> Cc: Christoph Lameter <clameter@sgi.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 23 7月, 2007 1 次提交
-
-
由 Sam Ravnborg 提交于
Fix following warning: WARNING: vmlinux.o(.text+0x188ea): Section mismatch: reference to .init.text:__alloc_bootmem_core (between 'alloc_bootmem_high_node' and 'get_gate_vma') alloc_bootmem_high_node() is only used from __init scope so declare it __init. And in addition declare the weak variant __init too. Signed-off-by: NSam Ravnborg <sam@ravnborg.org> Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 09 6月, 2007 1 次提交
-
-
由 Stephen Rothwell 提交于
into the appropriate #ifdef. Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: Andy Whitcroft <apw@shadowen.org> Cc: Badari Pulavarty <pbadari@us.ibm.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 01 6月, 2007 1 次提交
-
-
由 Zou Nan hai 提交于
On systems with huge amount of physical memory, VFS cache and memory memmap may eat all available system memory under 4G, then the system may fail to allocate swiotlb bounce buffer. There was a fix for this issue in arch/x86_64/mm/numa.c, but that fix dose not cover sparsemem model. This patch add fix to sparsemem model by first try to allocate memmap above 4G. Signed-off-by: NZou Nan hai <nanhai.zou@intel.com> Acked-by: NSuresh Siddha <suresh.b.siddha@intel.com> Cc: Andi Kleen <ak@suse.de> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 19 5月, 2007 1 次提交
-
-
由 Sam Ravnborg 提交于
modpost had two cases hardcoded for mm/ Shift over to __init_refok and kill the hardcoded function names in modpost. This has the drawback that the functions will always be kept no matter configuration. With previous code the function were placed in init section if configuration allowed it. Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
-
- 09 5月, 2007 2 次提交
-
-
由 Yasunori Goto 提交于
This patch is add white list into modpost.c for some functions and ia64's section to fix section mismatchs. sparse_index_alloc() and zone_wait_table_init() calls bootmem allocator at boot time, and kmalloc/vmalloc at hotplug time. If config memory hotplug is on, there are references of bootmem allocater(init text) from them (normal text). This is cause of section mismatch. Bootmem is called by many functions and it must be used only at boot time. I think __init of them should keep for section mismatch check. So, I would like to register sparse_index_alloc() and zone_wait_table_init() into white list. In addition, ia64's .machvec section is function table of some platform dependent code. It is mixture of .init.text and normal text. These reference of __init functions are valid too. Signed-off-by: NYasunori Goto <y-goto@jp.fujitsu.com> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Yasunori Goto 提交于
This is to fix many section mismatches of code related to memory hotplug. I checked compile with memory hotplug on/off on ia64 and x86-64 box. Signed-off-by: NYasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 07 5月, 2007 1 次提交
-
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 12月, 2006 2 次提交
-
-
由 Andy Whitcroft 提交于
NUMA node ids are passed as either int or unsigned int almost exclusivly page_to_nid and zone_to_nid both return unsigned long. This is a throw back to when page_to_nid was a #define and was thus exposing the real type of the page flags field. In addition to fixing up the definitions of page_to_nid and zone_to_nid I audited the users of these functions identifying the following incorrect uses: 1) mm/page_alloc.c show_node() -- printk dumping the node id, 2) include/asm-ia64/pgalloc.h pgtable_quicklist_free() -- comparison against numa_node_id() which returns an int from cpu_to_node(), and 3) mm/mpolicy.c check_pte_range -- used as an index in node_isset which uses bit_set which in generic code takes an int. Signed-off-by: NAndy Whitcroft <apw@shadowen.org> Cc: Christoph Lameter <clameter@engr.sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Christoph Lameter 提交于
The zone table is mostly not needed. If we have a node in the page flags then we can get to the zone via NODE_DATA() which is much more likely to be already in the cpu cache. In case of SMP and UP NODE_DATA() is a constant pointer which allows us to access an exact replica of zonetable in the node_zones field. In all of the above cases there will be no need at all for the zone table. The only remaining case is if in a NUMA system the node numbers do not fit into the page flags. In that case we make sparse generate a table that maps sections to nodes and use that table to to figure out the node number. This table is sized to fit in a single cache line for the known 32 bit NUMA platform which makes it very likely that the information can be obtained without a cache miss. For sparsemem the zone table seems to be have been fairly large based on the maximum possible number of sections and the number of zones per node. There is some memory saving by removing zone_table. The main benefit is to reduce the cache foootprint of the VM from the frequent lookups of zones. Plus it simplifies the page allocator. [akpm@osdl.org: build fix] Signed-off-by: NChristoph Lameter <clameter@sgi.com> Cc: Dave Hansen <haveblue@us.ibm.com> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 29 10月, 2006 1 次提交
-
-
由 Yasunori Goto 提交于
Add __GFP_NOWARN flag to calling of __alloc_pages() in __kmalloc_section_memmap(). It can reduce noisy failure message. In ia64, section size is 1 GB, this means that order 8 pages are necessary for each section's memmap. It is often very hard requirement under heavy memory pressure as you know. So, __alloc_pages() gives up allocation and shows many noisy stack traces which means no page for each sections. (Current my environment shows 32 times of stack trace....) But, __kmalloc_section_memmap() calls vmalloc() after failure of it, and it can succeed allocation of memmap. So, its stack trace warning becomes just noisy. I suppose it shouldn't be shown. Signed-off-by: NYasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 01 7月, 2006 1 次提交
-
-
由 Jörn Engel 提交于
Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: NAdrian Bunk <bunk@stusta.de>
-
- 28 6月, 2006 1 次提交
-
-
由 Ingo Molnar 提交于
locking init cleanups: - convert " = SPIN_LOCK_UNLOCKED" to spin_lock_init() or DEFINE_SPINLOCK() - convert rwlocks in a similar manner this patch was generated automatically. Motivation: - cleanliness - lockdep needs control of lock initialization, which the open-coded variants do not give - it's also useful for -rt and for lock debugging in general Signed-off-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NArjan van de Ven <arjan@linux.intel.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 23 6月, 2006 1 次提交
-
-
由 Andy Whitcroft 提交于
Record the node id as we mark sections for instantiation. Use this nid during instantiation to direct allocations. Signed-off-by: NAndy Whitcroft <apw@shadowen.org> Cc: Mike Kravetz <kravetz@us.ibm.com> Cc: Dave Hansen <haveblue@us.ibm.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Bob Picco <bob.picco@hp.com> Cc: Jack Steiner <steiner@sgi.com> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: Martin Bligh <mbligh@google.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 22 5月, 2006 1 次提交
-
-
由 Mike Kravetz 提交于
A bad calculation/loop in __section_nr() could result in incorrect section information being put into sysfs memory entries. This primarily impacts memory add operations as the sysfs information is used while onlining new memory. Fix suggested by Dave Hansen. Note that the bug may not be obvious from the patch. It actually occurs in the function's return statement: return (root_nr * SECTIONS_PER_ROOT) + (ms - root); In the existing code, root_nr has already been multiplied by SECTIONS_PER_ROOT. Signed-off-by: NMike Kravetz <kravetz@us.ibm.com> Cc: Dave Hansen <haveblue@us.ibm.com> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 16 5月, 2006 1 次提交
-
-
由 Mike Kravetz 提交于
slab_is_available() indicates slab based allocators are available for use. SPARSEMEM code needs to know this as it can be called at various times during the boot process. Signed-off-by: NMike Kravetz <kravetz@us.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 02 5月, 2006 1 次提交
-
-
由 Mike Kravetz 提交于
This patch fixes two bugs with the way sparsemem interacts with memory add. They are: - memory leak if memmap for section already exists - calling alloc_bootmem_node() after boot These bugs were discovered and a first cut at the fixes were provided by Arnd Bergmann <arnd@arndb.de> and Joel Schopp <jschopp@us.ibm.com>. Signed-off-by: NMike Kravetz <kravetz@us.ibm.com> Signed-off-by: NJoel Schopp <jschopp@austin.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 09 1月, 2006 1 次提交
-
-
由 Ravikiran G Thirumalai 提交于
____cacheline_maxaligned_in_smp is currently used to align critical structures and avoid false sharing. It uses per-arch L1_CACHE_SHIFT_MAX and people find L1_CACHE_SHIFT_MAX useless. However, we have been using ____cacheline_maxaligned_in_smp to align structures on the internode cacheline size. As per Andi's suggestion, following patch kills ____cacheline_maxaligned_in_smp and introduces INTERNODE_CACHE_SHIFT, which defaults to L1_CACHE_SHIFT for all arches. Arches needing L3/Internode cacheline alignment can define INTERNODE_CACHE_SHIFT in the arch asm/cache.h. Patch replaces ____cacheline_maxaligned_in_smp with ____cacheline_internodealigned_in_smp With this patch, L1_CACHE_SHIFT_MAX can be killed Signed-off-by: NRavikiran Thirumalai <kiran@scalex86.org> Signed-off-by: NShai Fultheim <shai@scalex86.org> Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 30 10月, 2005 2 次提交
-
-
由 Dave Hansen 提交于
This basically keeps up from having to extern __kmalloc_section_memmap(). The vaddr_in_vmalloc_area() helper could go in a vmalloc header, but that header gets hard to work with, because it needs some arch-specific macros. Just stick it in here for now, instead of creating another header. Signed-off-by: NDave Hansen <haveblue@us.ibm.com> Signed-off-by: NLion Vollnhals <webmaster@schiggl.de> Signed-off-by: NJiri Slaby <xslaby@fi.muni.cz> Signed-off-by: NYasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Dave Hansen 提交于
A little helper that we use in the hotplug code. Signed-off-by: NDave Hansen <haveblue@us.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 05 9月, 2005 3 次提交
-
-
由 Dave Hansen 提交于
This splits up sparse_index_alloc() into two pieces. This is needed because we'll allocate the memory for the second level in a different place from where we actually consume it to keep the allocation from happening underneath a lock Signed-off-by: NDave Hansen <haveblue@us.ibm.com> Signed-off-by: NBob Picco <bob.picco@hp.com> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Bob Picco 提交于
With cleanups from Dave Hansen <haveblue@us.ibm.com> SPARSEMEM_EXTREME makes mem_section a one dimensional array of pointers to mem_sections. This two level layout scheme is able to achieve smaller memory requirements for SPARSEMEM with the tradeoff of an additional shift and load when fetching the memory section. The current SPARSEMEM implementation is a one dimensional array of mem_sections which is the default SPARSEMEM configuration. The patch attempts isolates the implementation details of the physical layout of the sparsemem section array. SPARSEMEM_EXTREME requires bootmem to be functioning at the time of memory_present() calls. This is not always feasible, so architectures which do not need it may allocate everything statically by using SPARSEMEM_STATIC. Signed-off-by: NAndy Whitcroft <apw@shadowen.org> Signed-off-by: NBob Picco <bob.picco@hp.com> Signed-off-by: NDave Hansen <haveblue@us.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Bob Picco 提交于
A new option for SPARSEMEM is ARCH_SPARSEMEM_EXTREME. Architecture platforms with a very sparse physical address space would likely want to select this option. For those architecture platforms that don't select the option, the code generated is equivalent to SPARSEMEM currently in -mm. I'll be posting a patch on ia64 ml which uses this new SPARSEMEM feature. ARCH_SPARSEMEM_EXTREME makes mem_section a one dimensional array of pointers to mem_sections. This two level layout scheme is able to achieve smaller memory requirements for SPARSEMEM with the tradeoff of an additional shift and load when fetching the memory section. The current SPARSEMEM -mm implementation is a one dimensional array of mem_sections which is the default SPARSEMEM configuration. The patch attempts isolates the implementation details of the physical layout of the sparsemem section array. ARCH_SPARSEMEM_EXTREME depends on 64BIT and is by default boolean false. I've boot tested under aim load ia64 configured for ARCH_SPARSEMEM_EXTREME. I've also boot tested a 4 way Opteron machine with !ARCH_SPARSEMEM_EXTREME and tested with aim. Signed-off-by: NAndy Whitcroft <apw@shadowen.org> Signed-off-by: NBob Picco <bob.picco@hp.com> Signed-off-by: NDave Hansen <haveblue@us.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 24 6月, 2005 2 次提交
-
-
由 Andy Whitcroft 提交于
Make sparse's initalization be accessible at runtime. This allows sparse mappings to be created after boot in a hotplug situation. This patch is separated from the previous one just to give an indication how much of the sparse infrastructure is *just* for hotplug memory. The section_mem_map doesn't really store a pointer. It stores something that is convenient to do some math against to get a pointer. It isn't valid to just do *section_mem_map, so I don't think it should be stored as a pointer. There are a couple of things I'd like to store about a section. First of all, the fact that it is !NULL does not mean that it is present. There could be such a combination where section_mem_map *is* NULL, but the math gets you properly to a real mem_map. So, I don't think that check is safe. Since we're storing 32-bit-aligned structures, we have a few bits in the bottom of the pointer to play with. Use one bit to encode whether there's really a mem_map there, and the other one to tell whether there's a valid section there. We need to distinguish between the two because sometimes there's a gap between when a section is discovered to be present and when we can get the mem_map for it. Signed-off-by: NDave Hansen <haveblue@us.ibm.com> Signed-off-by: NAndy Whitcroft <apw@shadowen.org> Signed-off-by: NJack Steiner <steiner@sgi.com> Signed-off-by: NBob Picco <bob.picco@hp.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Andy Whitcroft 提交于
Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: NAndy Whitcroft <apw@shadowen.org> Signed-off-by: NDave Hansen <haveblue@us.ibm.com> Signed-off-by: NMartin Bligh <mbligh@aracnet.com> Signed-off-by: NAdrian Bunk <bunk@stusta.de> Signed-off-by: NYasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: NBob Picco <bob.picco@hp.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-