- 16 3月, 2012 3 次提交
-
-
由 Eliad Peller 提交于
uapsd_queues and uapsd_max_sp_len are relevant only for managed interfaces, and can be configured differently for each vif. Move them from the local struct to sdata->u.mgd, and update the debugfs functions accordingly. Signed-off-by: NEliad Peller <eliad@wizery.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Eliad Peller 提交于
Some debugfs write functions call kstrto* functions, which assume the string is null-terminated. Make it valid by changing ieee80211_if_write() to use static buffer instead of allocating one, and set the last char to NULL. (The write functions try to parse some integer/mac address, so 64 bytes buffer should be enough) Signed-off-by: NEliad Peller <eliad@wizery.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Helmut Schaa 提交于
The current max throughput rate is known to be good as otherwise it wouldn't be the max throughput rate. Since rate sampling can introduce some overhead (by adding RTS for example or due to not aggregating the frame) don't sample the max throughput rate. Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com> Acked-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 14 3月, 2012 4 次提交
-
-
由 Paul Stewart 提交于
When regulatory information changes our HT behavior (e.g, when we get a country code from the AP we have just associated with), we should use this information to change the power with which we transmit, and what channels we transmit. Sometimes the channel parameters we derive from regulatory information contradicts the parameters we used in association. For example, we could have associated specifying HT40, but the regulatory rules we apply may forbid HT40 operation. In the situation above, we should reconfigure ourselves to transmit in HT20 only, however it makes no sense for us to disable receive in HT40, since if we associated with these parameters, the AP has every reason to expect we can and will receive packets this way. The code in mac80211 does not have the capability of sending the appropriate action frames to signal a change in HT behaviour so the AP has no clue we can no longer receive frames encoded this way. In some broken AP implementations, this can leave us effectively deaf if the AP never retries in lower HT rates. This change breaks up the channel_type parameter in the ieee80211_enable_ht function into a separate receive and transmit part. It honors the channel flags set by regulatory in order to configure the rate control algorithm, but uses the capability flags to configure the channel on the radio, since these were used in association to set the AP's transmit rate. Signed-off-by: NPaul Stewart <pstew@chromium.org> Cc: Sam Leffler <sleffler@chromium.org> Cc: Johannes Berg <johannes@sipsolutions.net> Reviewed-by: NLuis R Rodriguez <mcgrof@frijolero.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This value is not really very useful by itself, yet some drivers (including iwlwifi until I can figure out what it should do) use it. At least rename it to "last_tsf" to indicate the meaning and add a note that it may be really old. I suspect the value may become useful combined with the rx_status->mactime, but we don't (yet) store that value and pass it to the driver. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Not linearizing every SKB will help actually pass non-linear SKBs all the way up when on an encrypted connection. For now, linearize TKIP completely as it is lower performance and I don't quite grok all the details. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This is better done inside the WEP decrypt function where it doesn't have to check all the conditions any more since they've been tested already. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 13 3月, 2012 10 次提交
-
-
由 Johannes Berg 提交于
The authentication and association handshake already happens in the context of the new BSS, and the basic rates are needed at least for the ACK response frame to the authentication or association response frames. Therefore the basic rates should already be configured into the driver when those frames are sent. Change the logic to set up the basic rates in the connection preparation that happens for authentication and association (if needed). Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
As associating is possible without first authenticating (for FT over DS) association also has to be able to switch to the right channel, insert the station entry etc. Factor out this common code into a new function called ieee80211_prep_connection(). Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The BSSID has been set a lot earlier already and didn't change again in ieee80211_set_associated(). Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Instead of setting assoc_data->wmm_used solely based on the BSS also take into account our own capabilities and later check those. Also rename "wmm_used" and "uapsd_used" to just "wmm" and "uapsd". Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Always set/use IEEE80211_STA_DISABLE_11N instead of duplicating the queue, WMM and HT checks in all places. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Looks like some changes in this area moved the code but not the comment that belongs to the code, move it to the right place. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Helmut Schaa 提交于
Disable multi stream rates (MCS > 7) when a STA is in static SMPS mode since it has only one active rx chain. Hence, it doesn't even make sense to sample multi stream rates. Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
As we've discussed, we want to avoid channel changes while associated. While the part when we actually associate needs a bit more work, the bit that happens on disassociating can be changed quite easily. Move the channel type change later in the disassociate process to set the channel only after the driver was told that it's now disassociated. As the driver could expect powersave to be enabled only when associated, this thus results in splitting the config call, but overall what happens makes more sense this way. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
When the station state callback was added, this was no longer needed in theory. With the iwlwifi changes to remove use of it landing, we can kill the entire tx-sync framework again, RIP. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Helmut Schaa 提交于
While setting up or tearing down a BA session mac80211 is buffering pending frames for the according TID. However, there's currently no limit on how many frames are buffered possibly leading to an out-of- memory situation. This can happen on systems with little memory when the CPU is fully loaded since the BA session work is executed in process context while frames can still come via softirq. Apply a limitation to the TIDs pending queue to avoid consuming too much memory in this situation. Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 08 3月, 2012 3 次提交
-
-
由 Thomas Pedersen 提交于
smatch was complaining: CHECK net/mac80211/mesh_pathtbl.c net/mac80211/mesh_pathtbl.c:562 mesh_path_add() error: double lock 'bottom_half:' net/mac80211/mesh_pathtbl.c:580 mesh_path_add() error: double unlock 'bottom_half:' net/mac80211/mesh_pathtbl.c:589 mesh_path_add() error: double unlock 'bottom_half:' net/mac80211/mesh_pathtbl.c:691 mpp_path_add() error: double lock 'bottom_half:' net/mac80211/mesh_pathtbl.c:707 mpp_path_add() error: double unlock 'bottom_half:' net/mac80211/mesh_pathtbl.c:716 mpp_path_add() error: double unlock 'bottom_half:' net/mac80211/mesh_pathtbl.c:814 mesh_path_flush_by_nexthop() error: double lock 'bottom_half:' net/mac80211/mesh_pathtbl.c:819 mesh_path_flush_by_nexthop() error: double unlock 'bottom_half:' net/mac80211/mesh_pathtbl.c:887 mesh_path_del() error: double lock 'bottom_half:' net/mac80211/mesh_pathtbl.c:901 mesh_path_del() error: double unlock 'bottom_half:' So don't lock / unlock with _bh() while bottom halves are already disabled. Reported-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NThomas Pedersen <thomas@cozybit.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ashok Nagarajan 提交于
The patch "{nl,cfg,mac}80211: Implement RSSI threshold for mesh peering" has a potential null pointer dereferencing problem. Thanks to Dan Carpenter for pointing out. This patch will fix the issue. Signed-off-by: NAshok Nagarajan <ashok@cozybit.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Paul Stewart 提交于
mac80211 is lenient with respect to reception of corrupted beacons. Even if the frame is corrupted as a whole, the available IE elements are still passed back and accepted, sometimes replacing legitimate data. It is unknown to what extent this "feature" is made use of, but it is clear that in some cases, this is detrimental. One such case is reported in http://crosbug.com/26832 where an AP corrupts its beacons but not its probe responses. One approach would be to completely reject frames with invaid data (for example, if the last tag extends beyond the end of the enclosing PDU). The enclosed approach is much more conservative: we simply prevent later IEs from overwriting the state from previous ones. This approach hopes that there might be some salient data in the IE stream before the corruption, and seeks to at least prevent that data from being overwritten. This approach will fix the case above. Further, we flag element structures that contain data we think might be corrupted, so that as we fill the mac80211 BSS structure, we try not to replace data from an un-corrupted probe response with that of a corrupted beacon, for example. Short of any statistics gathering in the various forms of AP breakage, it's not possible to ascertain the side effects of more stringent discarding of data. Signed-off-by: NPaul Stewart <pstew@chromium.org> Cc: Sam Leffler <sleffler@chromium.org> Cc: Eliad Peller <eliad@wizery.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 07 3月, 2012 3 次提交
-
-
由 Javier Cardona 提交于
Signed-off-by: NJavier Cardona <javier@cozybit.com> Reviewed-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Thomas Pedersen 提交于
Airtime link metric estimation was broken in HT mesh, use cfg80211_calculate_bitrate to get the right rate value. Also factor out tx rate copying from sta_set_sinfo(). Signed-off-by: NThomas Pedersen <thomas@cozybit.com> Reviewed-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Add the signal strength (in dBm only for now) to frames that are received via nl80211's various frame APIs. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Acked-by: NKalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 06 3月, 2012 8 次提交
-
-
由 Johannes Berg 提交于
When associating and particularly when disassociating there's no need to notify the driver about changes with multiple calls to bss_info_changed, we should combine the QoS enabling/disabling into the same call as otherwise the driver could get confused about QoS suddenly getting disabled while connected. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
There's no need to hardcode a subset of the radiotap header for cooked monitor receive, we can just reuse the normal monitor mode radiotap code. This simplifies the code and extends the information available on cooked monitor interfaces. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chun-Yeow Yeoh 提交于
RANN, PREP and PERR propagation should happen only if the dot11MeshForwarding is true. Besides, data frame should not be forwarded if dot11MeshForwarding is false. This redundant checking is necessary to avoid the broadcasted ARP breaking the non-forwarding rule. Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
For A-MPDU rx it makes sense to only process the signal strength once per aggregate instead of once per subframe. Additonally, some hardware (e.g. Atheros) only provides valid signal strength information for the last subframe. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
Because of the constant size and guaranteed 16 bit alignment, the inline compare_ether_addr function is much cheaper than calling memcmp. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
Several MAC address comparison functions assume 16 bit alignment for pointers passed to them. Since the addition of the control_port field, alignment for the IBSS bssid was off by one, causing a severe performance hit on architectures without efficient unaligned access (e.g. MIPS). Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ashok Nagarajan 提交于
Mesh peer links are established only if average rssi of the peer candidate satisfies the threshold. This is not in 802.11s specification but was requested by David Fulgham, an open80211s user. This is a way to avoid marginal peer links with stations that are barely within range. This patch adds a new mesh configuration parameter, mesh_rssi_threshold. This feature is supported only for hardwares that report signal in dBm. Signed-off-by: NAshok Nagarajan <ashok@cozybit.com> Signed-off-by: NJavier Cardona <javier@cozybit.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chun-Yeow Yeoh 提交于
According to Section Y.7.4 Actions on receipt of proactive RANN, an individually addressed PREQ should be generated towards the neighbor peer mesh STA indicated in the RANN Sender Address field in the forwarding information. Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: NJavier Cardona <javier@cozybit.com> Signed-off-by: NThomas Pedersen <thomas@cozybit.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 01 3月, 2012 5 次提交
-
-
由 Johannes Berg 提交于
This renames the IEEE80211_TX_CTL_POLL_RESPONSE TX flag to IEEE80211_TX_CTL_NO_PS_BUFFER and also uses it for non-bufferable MMPDUs (all MMPDUs but deauth, disassoc and action frames.) Previously, mac80211 would let the MMPDU through but not set the flag so drivers supporting some hardware aids for avoiding the PS races would then reject the frame. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The association sequence looks (roughly) like this now: * set BSSID * set station to EXIST state * send auth * set station to AUTH state * send assoc * set station to ASSOC state * set BSS info to associated In contrast, the deauth/disassoc sequence is the other way around: * clear BSSID/BSS info state * remove station * send deauth/disassoc (in some cases the last two steps are reversed.) This patch encodes the entire sequence in the ieee80211_set_disassoc() function and changes it to be like this, for good measure with an explicit flush: * send deauth/disassoc * flush * remove station * clear BSSID/BSS info state At least iwlwifi gets confused with the other sequence in P2P mode and complains that it wasn't able to flush the queues. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
When ieee80211_set_disassoc() is called with the tx argument set to true, it will send DelBA out to the peer. This isn't useful or necessary in a few cases where we do it today, those being when we lost the connection or when the supplicant explicitly asked us to not tell the AP. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Instead of calling cfg80211 in ieee80211_send_deauth_disassoc() pass out the frame and call it from the caller. That saves the SKB allocation if we don't actually want to send the frame and enables us to make the ordering smarter in the future. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
In "cfg80211: no cookies in cfg80211_send_XXX()" Holger Schurig removed the cookies in the calls from mac80211 to cfg80211, but the ones in the other direction were left in. Remove them now. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 2月, 2012 4 次提交
-
-
由 Johannes Berg 提交于
That's a lot longer than open-coding it and doesn't really add value, so just remove it. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The comment for sta_info_flush() states "Returns the number of removed STA entries" but that isn't actually true. Consequently, the warning when a station is still around on interface removal can never trigger and this delayed finding the timer issue the previous patch fixed. Fix the return value here to make that warning useful again. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
When removing an interface while it is in the process of authenticating or associating, we leak the auth_data or assoc_data, and leave the timer pending. The timer then crashes the system when it fires as its data is gone. Fix this by explicitly deleting all the data when the interface is removed. This uncovered another bug -- this problem should have been detected by the sta_info_flush() warning but that function doesn't ever return non-zero, I'll fix that in a separate patch. Reported-by: NHieu Nguyen <hieux.c.nguyen@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jakub Kicinski 提交于
Use interface data from sta instead of invalid pointer to list head in calls to drv_sta_state. Signed-off-by: NJakub Kicinski <kubakici@wp.pl> Reviewed-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-