The verb command in stac92xx_post_suspend caused the audio to stop
working after resuming from S3 mode on HP laptops with the VREF-pin
mute-LED control.  Removing relevant post_suspend registering.

Although removing D3 on AFG is no optimal solution, the impact should
be small in comparison with the broken S3/S4.
Signed-off-by: NCharles Chin <Charles.Chin@idt.com>
Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This quirk sould be reverted. It has the following probems:

1) The quirk was intended to "ASUS MV2-MX SE" motherboards only, but the
ID used matches a much broader range, potentially all boards containing a
VIA chipset model in the family of vendor VIA 0x1106 and audio device ID
0x3288, which encompasses VIA-VT82xx, VIA-VT1xx and VIA-VT20xx chipsets.

2) VIA chipsets rely on azx_via_get_position() to handle correctly dma
transfers during capture. Using POS_FIX_LPIB instead of POS_FIX_VIACOMBO
leads to partially corrupted input buffers during capture. The effects
of this bug are not immediately visible, it took strong DSP expertise,
some expensive signal generator and a spectrum analyzer to identify it
and verify correct behaviour using original default.

3) It's almost certain that the quirk did not fix the real problem,
if there was one. Refer to original submission:
http://mailman.alsa-project.org/pipermail/alsa-devel/2010-February/025109.htmlSigned-of-by: NMarc Vertes <mvertes@sigfox.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some HP laptops use a pin VREF for controlling the mute LED, and such a
pin shouldn't be powered off.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Currently the SigmaDSP firmware loader only works correctly on little-endian
systems. Fix this by using the proper endianess conversion functions.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The firmware header is not part of the CRC, so skip it. Otherwise the firmware
will be rejected due to non-matching CRCs.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The SigmaDSP firmware loader currently does not perform enough boundary size
checks when processing the firmware. As a result it is possible that a
malformed firmware can cause an out of bounds memory access.

This patch adds checks which ensure that both the action header and the payload
are completely inside the firmware data boundaries before processing them.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Added table quirks entry for Roland GAIA SH-01 Synthesizer based upon
Roland SH-201 table entry as template.  USB MIDI and audio was tested
with Muse and Audacity.
Signed-off-by: NJohn F Leach <jfleach@jfleach.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Based on initial data.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

VT1708 has no support for unsolicited events per jack-plug, the driver
implements the workq for polling the jack-detection.  The mixer element
"Jack Detect" was supposed to control this behavior on/off, but this
doesn't work properly as is now.  The workq is always started and the
HP automute is always enabled.

This patch fixes the jack-detect control behavior by triggering / stopping
the work appropriately at the state change.  Also the work checks the
internal state to continue scheduling or not.

Cc: <stable@kernel.org> [v3.1]
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The CS420X_IMAC27 was copied from the line before but CS420X_APPLE
was clearly intented.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There are cases where there is no working codec on the soc-audio devices,
and snd_soc_suspend() will skip such device when suspending. Yet its
counterpart snd_soc_resume() does not check this, causing complaints
about spinlock lockup:

[  176.726087] BUG: spinlock lockup on CPU#0, kworker/0:2/1067, d8ab82a8
[  176.732539] [<80014a14>] (unwind_backtrace+0x0/0xec) from [<805b3fc8>] (dump_stack+0x20/0x24)
[  176.741082] [<805b3fc8>] (dump_stack+0x20/0x24) from [<80322208>] (do_raw_spin_lock+0x118/0x158)
[  176.749882] [<80322208>] (do_raw_spin_lock+0x118/0x158) from [<805b7874>] (_raw_spin_lock_irqsave+0x5c/0x68)
[  176.759723] [<805b7874>] (_raw_spin_lock_irqsave+0x5c/0x68) from [<8002a020>] (__wake_up+0x2c/0x5c)
[  176.768781] [<8002a020>] (__wake_up+0x2c/0x5c) from [<804a6de8>] (soc_resume_deferred+0x3c/0x2b0)
[  176.777666] [<804a6de8>] (soc_resume_deferred+0x3c/0x2b0) from [<8004ee20>] (process_one_work+0x2e8/0x50c)
[  176.787334] [<8004ee20>] (process_one_work+0x2e8/0x50c) from [<8004fd08>] (worker_thread+0x1c8/0x2e0)
[  176.796566] [<8004fd08>] (worker_thread+0x1c8/0x2e0) from [<80053ec8>] (kthread+0xa4/0xb0)
[  176.804843] [<80053ec8>] (kthread+0xa4/0xb0) from [<8000ea70>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: NEric Miao <eric.miao@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Just checking the code in cs42l51_fill_cache():
The cache pointer points to codec->reg_cache + 1.
I think it is because CS42L51_FIRSTREG is 0x01,
so codec->reg_cache[0] is not used here.

Then we read CS42L51_NUMREGS bytes to cache.
So we need reg_cache_size to be CS42L51_NUMREGS + 1.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

SoC Audio support for PlayPaq with WM8510 got added in commit 9aaca968
("[ALSA] Revised AT32 ASoC Patch"). That support depends on
BOARD_PLAYPAQ. That Kconfig symbol didn't exist when that support got
added in v2.6.27. It still doesn't. It has never been possible to even
build this driver. Drop it.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use an inline function for the common pattern for assigning a capsrc.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the imux entries are rebuilt in alc_rebuild_imux_for_auto_mic(),
the initialization of index field is missing.  It may work without it
casually when the original imux was created by the auto-parser, but
it's definitely broken in the case of static configs where no imux was
parsed beforehand.  Because of this, the auto-mic switching doesn't
work properly on some model options.

This patch adds the missing initialization of index field.
Reported-by: NDmitry Nezhevenko <dion@inhex.net>
Cc: <stable@kernel.org> [v3.1]
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The PCI SSID 8086:7270 is commonly used for multiple Apple machines,
thus we can't use it as identifier for a unique model.  Because of this
conflict, some machines show weird behavior.  For example, MacBook Air
shows Front and Surround speakers although only Surround works due to
the wrongly overridden pin-configuration for imac27.

This patch fixes two things:
- Stop the wrong pin-config override of imac27 by removing PCI SSID
  entry for avoiding the wrong mappings,
- Add the generic GPIO setup for Apple machines by checking the codec
  SSID vendor bits
Tested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Tested-by: NDirk Hohndel <hohndel@infradead.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In snd_hda_check_board_codec_sid_config(), not only comparing with the
exact value but allow the bit-mask comparison for vendor-only, etc.
Tested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Tested-by: NDirk Hohndel <hohndel@infradead.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Commit ac601555 ("ASoC: Return early with -EINVAL if invalid dai format is
detected") requires the machine driver to tell the CS4270 codec driver
whether the CS4270 should be configured for master or slave operation.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Replace the manual register restore mechanism in cs4270.c and call the
generic snd_soc_cache_sync() handler instead.

This factors code out in favour of core facilities and also fixes a
bus confusion that is most probably caused by intermixing i2c-regmap
functions and i2c_smbus_* accessors.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Reported-and-tested-by: NSven Neumann <s.neumann@raumfeld.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds <linux/modules.h> to fix following build errors.

sound/soc/codecs/wm8994.c: In function 'wm8994_readable':
sound/soc/codecs/wm8994.c:58: warning: unused variable 'wm8994'
sound/soc/samsung/smdk_wm8994.c:176: error: expected declaration specifiers or '...' before string constant
sound/soc/samsung/smdk_wm8994.c:176: warning: data definition has no type or storage class
sound/soc/samsung/smdk_wm8994.c:176: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
sound/soc/samsung/smdk_wm8994.c:176: warning: function declaration isn't a prototype
sound/soc/samsung/smdk_wm8994.c:177: error: expected declaration specifiers or '...' before string constant
Signed-off-by: NBoojin Kim <boojin.kim@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In the case of ((max9877_regs[reg] >> shift) & mask) != val
but ((max9877_regs[reg2] >> shift) & mask) == val2,
current code does not update the registers.

Fix the logic to update registers if either val or val2 is changed.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

According to the datasheet:
The BIT[5:4] of ADC Control Register 2 is to control the word width.
        00 = 25 Bits
        01 = 20 Bits
        10 = 16 Bits
        11 = Invalid

Thus, the AD1836_ADC_WORD_OFFSET should be defined as 4.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

With the ELD repoll mechanism, we can (and should) fail the ELD reading
immediately when find something obviously wrong and let the caller retry
after some delay.
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

commit 6175ddf0 optimized the mem*io
functions that have been used to send commands to the device. these
optimizations somehow corrupted the communication with the lx6464es,
that resulted the device to be unusable with kernels after 2.6.33.

this patch emulates the memcpy_*_io functions via a loop to avoid these
problems.
Signed-off-by: NTim Blechmann <tim@klingt.org>
LKML-Reference: <4ECB5257.4040600@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

the command buffer is only accessed from one file, so we can declare the
specific functions as static in that file
Signed-off-by: NTim Blechmann <tim@klingt.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Improve the one-shot ELD repoll to up to 6 retries.

Up to now the 300ms looks sufficient for the test boxes. However
I'm a bit worried about how well it can fit the wider user base.
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Commit c09403dc has introduced a
regression: PCIe versions of RME MADI were no longer detected, because
the MADIface ID (0xd5) was used instead of the correct 0xd2.

This commit fixes the problem.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

desc->size is supposed to be a le16 type.  On a big endian system the
current code will set ->size to zero.  We fixed a similar bug
on the next line but missed this one.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NAlexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the arrays.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the arrays.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>