Some cpufreq drivers (at that time, only powernow-k7) need to recalibrate the
cpu_khz at runtime.
Signed-off-by: NBruno Ducrot <ducrot@poupinou.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDave Jones <davej@redhat.com>

We have to recalibrate cpu_khz in order to use the current FID instead the max
FID since some BIOS do not put the processor at maximum frequency at POST. 
Also, some BIOS will change the processor frequency at our back after cpu_khz
was calibrate.  Finally, this will fix a long standing bug when we do
something like this:

# rmmod powernow-k7
# modprobe powernow-k7
Signed-off-by: NBruno Ducrot <ducrot@poupinou.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDave Jones <davej@redhat.com>

From: Sean Young <sean@mess.org>
Signed-off-by: NDave Jones <davej@redhat.com>

This comes up time and time again. Until its fixed, place this
comment in the Kconfig which should stem the flow of resubmissions.
Signed-off-by: NRob Weryk <rjweryk@uwo.ca>
Signed-off-by: NDave Jones <davej@redhat.com>

The speedstep-smi driver actually works on >=1 notebook with a
Pentium 4-M CPU where all other cpufreq drivers fail. Therefore,
allow speedstep-smi on P4Ms again, but warn users of likely failure
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NDave Jones <davej@redhat.com>

Trivial ondemand governor clean-ups:
- change from sampling_rate_in_HZ() to the official function
usecs_to_jiffies().
- use for_each_online_cpu() to instead of using "if (cpu_online(i))"
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NDave Jones <davej@redhat.com>

The Pentium 4 - Ms (HT) with CPUID 0xF34 and 0xF41 seem to support
centrino-like enhanced speedstep; however, no "table" support is possible.
Therefore, put NULL entries into speedstep-centrino.c
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NDave Jones <davej@redhat.com>

cpufreq core is printing out messages at KERN_WARNING level that the core
recovers from without intervention, and that the system administrator can
do nothing about.  Patch below reduces the severity of these messages to
debug.
Signed-off-by: NMatt Domsch <Matt_Domsch@dell.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDave Jones <davej@redhat.com>

Signed-off-by: NDave Jones <davej@redhat.com>

in fs/udf/udftime.c the global array '__mon_yday' is not static, and it
conflicts with the glibc one when the kernel is compiled as user mode.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In file included from drivers/firmware/pcdp.c:18:
drivers/firmware/pcdp.h:48: error: field `addr' has incomplete type
drivers/firmware/pcdp.c: In function `setup_serial_console':
drivers/firmware/pcdp.c:27: error:  `ACPI_ADR_SPACE_SYSTEM_MEMORY' undeclared (first use in this  function)

Cc: <tony.luck@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

flush_icache_range() is used in two different situation - in binfmt_elf.c &
co for user space mappings and module.c for kernel modules.  On m68k
flush_icache_range() doesn't know which data to flush, as it has separate
address spaces and the pointer argument can be valid in either address
space.

First I considered splitting flush_icache_range(), but this patch is
simpler.  Setting the correct context gives flush_icache_range() enough
information to flush the correct data.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We used to have an iseries specific profiler that used /proc/profile.  Now
thats gone we can use the generic timer based stuff.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

h8300 appears to sleep (halt) when need_resched IS set.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is a neverending story

linux/acpi.h contains empty declarations for acpi_boot_init() &
acpi_boot_table_init() but they are nested inside #ifdef CONFIG_ACPI.

So we'll have to #ifdef in arch/i386/kernel/setup.c: setup_arch()
Signed-off-by: NAlexander Nyberg <alexn@telia.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make CONFIG_X86_PM_TIMER dependent on CONFIG_ACPI
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Suggested by Alexander Nyberg
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I was gently reminded that there are per-cpu forms of the EXPORT_SYMBOL macros.
Signed-off-by: NTony Luck <tony.luck@intel.com>

Only the address needs alignment of mask bits, length should work with
a relaxed alignment check.
Signed-off-by: NJens Axboe <axboe@suse.de>

[ This is take 2: make the length check be for 16-byte alignment, not
  just word alignment.  That should hopefully keep everybody happy,
  while still allowing CD writing with DMA ]
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When I sent in the patch adding the code for the kernel to tell the
firmware about its capabilities on pSeries machines, I included the
function to give the capabilities to firmware but somehow forgot the
hunk that adds the call to the new function.  This patch adds the
call.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are intentionally ignoring the copy_to_user() value,
make it clear to the compiler too.

Noted by Jeff Garzik.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJon Mason <jdmason@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It cannot work properly, so just ignore it in drr
and rr multipath algorithms just like the random
multipath algorithm does.

Suggested by Herbert Xu.

Signed-off by: Pravin B. Shelar <pravins@calsoftinc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds is_multicast_ether_addr() to go along with
is_valid_ether_addr() and friends. It then changes
is_valid_ether_addr() to use the new macro, and fixes up the comment
on that function to move implementation details out of the API doco.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add an option to make secondary IP addresses get promoted
when primary IP addresses are removed from the device.
It defaults to off to preserve existing behavior.
Signed-off-by: NHarald Welte <laforge@gnumonks.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

	rsync://rsync.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev

Add tg3_nvram_lock() and tg3_nvram_unlock() calls around tg3_halt_cpu().
It is possible that the bootcode may be loading code from nvram during
this call and stopping the cpu without getting the lock may cause
uncompleted nvram data to be left in the nvram data register. Subsequent
calls to read/write nvram data will fail.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This test uses the previously added tg3_test_interrupt() to perform the
test.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The test will loopback one packet in MAC loopback mode and verify the
packet data.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a reset kind parameter to tg3_halt() so that the RESET_KIND_SUSPEND
parameter can be passed to tg3_halt() before doing offline tests.

All other calls to tg3_halt() will use the RESET_KIND_SHUTDOWN
parameter.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This improves the bridge local receive path by avoiding going
through another softirq.  The bridge receive path is already being called
from a netif_receive_skb() there is no point in going through another
receiveq round trip.

Recursion is limited because bridge can never be a port of a bridge
so handle_bridge() always returns.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>