Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NEric Anholt <eric@anholt.net>

New memory control config reg at 0x50 should be used for stolen
memory size detection on Sandybridge.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NEric Anholt <eric@anholt.net>

I can't explain this, except that it makes my display correct.
Signed-off-by: NEric Anholt <eric@anholt.net>

I don't know if this is what we'll want to be using long term, we'll see.
Signed-off-by: NEric Anholt <eric@anholt.net>

The register's moved to the same location as the one for the BCS, it seems.
Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NEric Anholt <eric@anholt.net>

* korg/drm-radeon-testing: (62 commits)
  drm/radeon/kms: update new pll algo
  drm/radeon/kms: add support for square microtiles on r3xx-r5xx
  drm/radeon/kms: force pinning buffer into visible VRAM
  drm/radeon/kms/evergreen: fix typo in cursor code
  drm/radeon/kms: implement reading active PCIE lanes on R600+
  drm/radeon/kms: for downclocking non-mobility check PERFORMANCE state
  drm/radeon/kms: simplify storing current and requested PM mode
  drm/radeon: fixes for r6xx/r7xx gfx init
  drm/radeon/rv740: fix backend setup
  drm/radeon/kms: fix R3XX/R4XX memory controller initialization
  [rfc] drm/radeon/kms: pm debugging check for vbl.
  drm/radeon: Fix memory allocation failures in the preKMS command stream checking.
  drm: Add generic multipart buffer.
  drm/radeon/kms: simplify memory controller setup V2
  drm/radeon: Add asic hook for dma copy to r200 cards.
  drm/radeon/kms: Create asic structure for r300 pcie cards.
  drm/radeon/kms: remove unused r600_gart_clear_page
  drm/radeon/kms: remove HDP flushes from fence emit (v2)
  drm/radeon/kms: add LVDS pll quirk for Dell Studio 15
  drm/radeon/kms: simplify picking power state
  ...

Conflicts:
	drivers/gpu/drm/radeon/atom.c
	drivers/gpu/drm/radeon/atombios.h
	drivers/gpu/drm/radeon/atombios_dp.c
	drivers/gpu/drm/radeon/r600.c
	drivers/gpu/drm/radeon/r600_audio.c
	drivers/gpu/drm/radeon/r600_cp.c
	drivers/gpu/drm/radeon/radeon.h
	drivers/gpu/drm/radeon/radeon_connectors.c
	drivers/gpu/drm/radeon/radeon_ring.c
	drivers/gpu/drm/radeon/rv770.c

* anholt/drm-intel-next:
  drm/i915: Record batch buffer following GPU error
  drm/i915: give up on 8xx lid status
  drm/i915: reduce some of the duplication of tiling checking
  drm/i915: blow away userspace mappings before fence change
  drm/i915: move a gtt flush to the correct place
  agp/intel: official names for Pineview and Ironlake
  drm/i915: overlay: drop superflous gpu flushes
  drm/i915: overlay: nuke readback to flush wc caches
  drm/i915: provide self-refresh status in debugfs
  drm/i915: provide FBC status in debugfs
  drm/i915: fix drps disable so unload & re-load works
  drm/i915: Fix OGLC performance regression on 945
  drm/i915: Deobfuscate the render p-state obfuscation
  drm/i915: add dynamic performance control support for Ironlake
  drm/i915: enable memory self refresh on 9xx
  drm/i915: Don't reserve compatibility fence regs in KMS mode.
  drm/i915: Keep MCHBAR always enabled
  drm/i915: Replace open-coded eviction in i915_gem_idle()

* korg/drm-core-next:
  drm/ttm: handle OOM in ttm_tt_swapout
  drm/radeon/kms/atom: fix shr/shl ops
  drm/kms: fix spelling of "CLOCK"
  drm/kms: fix fb_changed = true else statement
  drivers/gpu/drm/drm_fb_helper.c: don't use private implementation of atoi()
  drm: switch all GEM/KMS ioctls to unlocked ioctl status.
  Use drm_gem_object_[handle_]unreference_unlocked where possible
  drm: introduce drm_gem_object_[handle_]unreference_unlocked

- Without this change I get a general protection fault.
- Also use PTR_ERR where applicable.
Signed-off-by: NMaarten Maathuis <madman2003@gmail.com>
Reviewed-by: NDave Airlie <airlied@redhat.com>
Acked-by: NThomas Hellstrom <thellstrom@vmware.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

The whole attribute table is valid for
shr/shl ops.

Fixes fdo bug 26668
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

- add support for pre-avivo chips
- add support for fixed post/ref dividers
- add support for non-fractional fb dividers

By default avivo chips use the new algo and
pre-avivo chips use the old algo. Use the "new_pll"
module option to toggle between them.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMarek Olšák <maraeo@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch properly set visible VRAM and enforce any pinned buffer
to be into visible VRAM. We might later add a flag to release this
constraint for some newer hw more clever than previous.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

cursor x/y are surface relative.

fixes fdo bug 26551
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
  parisc: Set PCI CLS early in boot.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Fix broken sn2 build

Set the PCI CLS early in the boot process to prevent
device failures. In pcibios_set_master use the new
pci_cache_line_size instead of a hard-coded value.
Signed-off-by: NCarlos O'Donell <carlos@codesourcery.com>
Reviewed-by: NGrant Grundler <grundler@google.com>
Signed-off-by: NKyle McMartin <kyle@redhat.com>

* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Fix out_le32() macro
  microblaze: Fix cache loop function for cache range

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  Revert "block: improve queue_should_plug() by looking at IO depths"

Trailing semicolon causes compilation involving out_le32() to fail.
Signed-off-by: NSteven J. Magnani <steve@digidescorp.com>
Signed-off-by: NMichal Simek <monstr@monstr.eu>

I create wrong asm code but none test shows that this part of code is wrong.
I am not convinces that were good idea to create asm optimized macros
for caches. The reason is that there is not optimization with previous code
that's why make sense to add old code and do some benchmarking which
functions are faster.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net: bug fix for vlan + gro issue
  tc35815: Remove a wrong netif_wake_queue() call which triggers BUG_ON
  cdc_ether: new PID for Ericsson C3607w to the whitelist (resubmit)
  IPv6: better document max_addresses parameter
  MAINTAINERS: update mv643xx_eth maintenance status
  e1000: Fix DMA mapping error handling on RX
  iwlwifi: sanity check before counting number of tfds can be free
  iwlwifi: error checking for number of tfds in queue
  iwlwifi: set HT flags after channel in rxon

Traffic (tcp) doesnot start on a vlan interface when gro is enabled.
Even the tcp handshake was not taking place.
This is because, the eth_type_trans call before the netif_receive_skb
in napi_gro_finish() resets the skb->dev to napi->dev from the previously
set vlan netdev interface. This causes the ip_route_input to drop the
incoming packet considering it as a packet coming from a martian source.

I could repro this on 2.6.32.7 (stable) and 2.6.33-rc7.
With this fix, the traffic starts and the test runs fine on both vlan
and non-vlan interfaces.

CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: Be in TS_POLLING state during mwait based C-state entry
  ACPI: Fix regression where _PPC is not read at boot even when ignore_ppc=0
  acer-wmi: Respect current backlight level when loading

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/vmwgfx: Fix queries if no dma buffer thrashing is occuring.
  drm/nv50: fix vram ptes on IGPs to point at stolen system memory
  drm/nv50: fix instmem binding on IGPs to point at stolen system memory
  drm/nv50: improve vram page table construction
  drm/nv50: more efficient clearing of gpu page table entries
  drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
  drm/nouveau: Fix up pre-nv17 analog load detection.

Revert the change made to arch/ia64/sn/kernel/setup.c by commit
204fba4a as it breaks the build.

Fixing the build the b94b0808 way
breaks xpc because genksyms then fails to generate an CRC for
per_cpu____sn_cnodeid_to_nasid because of limitations in the
generic genksyms code.
Signed-off-by: NHedi Berriche <hedi@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The netif_wake_queue() is called correctly (i.e. only on !txfull
condition) from txdone routine.  So Unconditional call to the
netif_wake_queue() here is wrong.  This might cause calling of
start_xmit routine on txfull state and trigger BUG_ON.

This bug does not happen when NAPI disabled.  After txdone there
must be at least one free tx slot.  But with NAPI, this is not
true anymore and the BUG_ON can hits on heavy load.

In this driver NAPI was enabled on 2.6.33-rc1 so this is
regression from 2.6.32 kernel.
Reported-by: NRalf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new vid/pid to the cdc_ether whitelist.

Device added:
- Ericsson Mobile Broadband variant C3607w
Signed-off-by: NTorgny Johansson <torgny.johansson@gmail.com>

--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.htmlSigned-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Morton wrote:
>> >From ip-sysctl.txt file in kernel documentation I can see following description
>> for max_addresses:
>> max_addresses - INTEGER
>>         Number of maximum addresses per interface.  0 disables limitation.
>>         It is recommended not set too large value (or 0) because it would
>>         be too easy way to crash kernel to allow to create too much of
>>         autoconfigured addresses.
           ^^^^^^^^^^^^^^

>> If this parameter applies only for auto-configured IP addressed, please state
>> it more clearly in docs or rename the parameter to show that it refers to
>> auto-configuration.

It did mention autoconfigured in the text, but the below makes it more obvious.

More clearly document IPv6 max_addresses parameter.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I am no longer with Marvell.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check for error return from pci_map_single/pci_map_page and clean up.

With this and the previous patch the driver was able to handle a significant
percentage of errors (I set the fault injection rate to 10% and could still
download large files at a reasonable speed).
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit fb1e7538.

"Benjamin S." <sbenni@gmx.de> reports that the patch in question
causes a big drop in sequential throughput for him, dropping from
200MB/sec down to only 70MB/sec.

Needs to be investigated more fully, for now lets just revert the
offending commit.

Conflicts:

	include/linux/blkdev.h
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Intercept query commands and apply relocations to their guest pointers.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>