- 30 8月, 2008 27 次提交
-
-
由 Dan Williams 提交于
And while we're at it, grab min/max TX power from the firmware and use that to validate incoming TX power requests from WEXT. Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Although a revision 5 SPROM has not been seen in the wild, the open-source portion of the MIPS driver 4.150.10.5 describes its layout, which is mostly inherited from revision 4. This patch implements the differences. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Acked-by: NMichael Buesch <mb@bu3sch.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Daniel Wagner 提交于
Bit 4-5 of DSCP should not be considered by classify_d1. The 802.11 QoS Priority field is only depending on the precedence level. Signed-off-by: NDaniel Wagner <wagi@monom.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jouni Malinen 提交于
Clean up and extend scan result processing by storing all the IEs from Beacon/Probe Response frames in a single block instead of allocating memory for each specific IE separately. This removes lot of unnecessary code and automatically supports reporting of new IEs (e.g., IEEE 802.11r) into user space without need to manually extend mac80211 scanning code whenever a new protocol adds IE(s). Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Don't trim the FCS before passing the frame to mac80211, move TSF_TO_TU to core.h and delete more unused macros. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Also, Max RX-ampdu and mpdu-density are ath9k specific. Rename appropriately. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
This patch adds a HT Capability (DSSS/CCK Mode in 40MHz BSS) definition to ieee80211.h Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
This patch removes ath_vap_listen() and dma wrapper macros. Also, Inline abuse is cleaned up and a few typos are fixed. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Remove dead code, add newlines, fix indentation. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Use direct pci functions instead. Also, use sc_ht_info.tx_chan_width directly and remove ath_cwm_macmode. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jouni Malinen 提交于
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jouni Malinen 提交于
Use TX control flag IEEE80211_TX_CTL_ASSIGN_SEQ as a request to update the seq# for the frames. This will likely require some further cleanup to get seq# correctly for Beacons vs. other frames and also potentially for multiple BSSes. Anyway, this is better than ending up sending out most frames with seq# 0. Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jouni Malinen 提交于
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jouni Malinen 提交于
This change moves ath9k to use mac80211-generated Beacon frames instead of trying to allocate a single Beacon frame and then update it. In addition, the remaining ath_skb_{map,unmap}_single() wrapper calls are replaced with direct pci_{map,unmap}_single() calls in beacon.c. Power save buffering for multicast/broadcast frames is not yet converted to use mac80211-style (frames to be buffered inside mac80211, not in driver). Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jouni Malinen 提交于
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Add sc_rxflush and sc_noreset as bitfields to sc_flags. Remove a few variables and function prototypes that are unused. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
ah_opmode and sc_opmode are redundant. This patch removes sc_opmode. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jouni Malinen 提交于
This change adds a new cfg80211 command, NL80211_CMD_SET_BSS, to allow AP mode BSS parameters to be changed from user space (e.g., hostapd). The drivers using mac80211 are expected to be modified with separate changes to use the new BSS info parameter for short slot time in the bss_info_changed() handler. Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Otherwise, drivers are required to keep track of the sequence numbers themselves, and they really shouldn't be since we already do it for them. I'll fix the race once we figure out how this code should work at all, it's currently disabled. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 27 8月, 2008 10 次提交
-
-
由 Gerrit Renker 提交于
The BUG_ON(w_tot == 0) only holds if there is no more than 1 loss interval in the loss history. If there is only a single loss interval, the calc_i_mean() routine need in fact not be called (RFC 3448, 6.3.1). Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
-
由 Gerrit Renker 提交于
This sets the sysfs permissions so that root can toggle the `debug' parameter available for nearly every DCCP module. This is useful since there are various module inter-dependencies. The debug flag can now be toggled at runtime using echo 1 > /sys/module/dccp/parameters/dccp_debug echo 1 > /sys/module/dccp_ccid2/parameters/ccid2_debug echo 1 > /sys/module/dccp_ccid3/parameters/ccid3_debug echo 1 > /sys/module/dccp_tfrc_lib/parameters/tfrc_debug The last is not very useful yet, since no code at the moment calls the tfrc_debug() macro. Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
-
由 Gerrit Renker 提交于
dccp_disconnect() can be called due to several reasons: 1. when the connection setup failed (inet_stream_connect()); 2. when shutting down (inet_shutdown(), inet_csk_listen_stop()); 3. when aborting the connection (dccp_close() with 0 linger time). In case (1) the write queue is empty. This patch empties the write queue, if in case (2) or (3) it was not yet empty. This avoids triggering the write-queue BUG_TRAP in sk_stream_kill_queues() later on. It also seems natural to do: when breaking an association, to delete all packets that were originally intended for the soon-disconnected end (compare with call to tcp_write_queue_purge in tcp_disconnect()). Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
-
由 Gerrit Renker 提交于
This updates the use of the `out_invalid_option' label, which produces a Reset (code 5, "Option Error"), to fill in the Data1...Data3 fields as specified in RFC 4340, 5.6. Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
-
由 Gerrit Renker 提交于
This updates the option-parsing code with regard to RFC 4340, 5.8: "[..] options with nonsensical lengths (length byte less than two or more than the remaining space in the options portion of the header) MUST be ignored, and any option space following an option with nonsensical length MUST likewise be ignored." Hence in the following cases erratic options will be ignored: 1. The type byte of a multi-byte option is the last byte of the header options (i.e. effective option length of 1). 2. The value of the length byte is less than the minimum 2. This has been changed from previously 3: although no multi-byte option with a length less than 3 yet exists (cf. table 3 in 5.8), a length of 2 is valid. (The switch-statement in dccp_parse has further per-option length checks.) 3. The option length exceeds the length of the remaining option space. Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
-
由 Wei Yongjun 提交于
RFC4340 states that if a packet is received with an option error (such as a Mandatory Option as the last byte of the option list), the endpoint should repond with a Reset. In the LISTEN and RESPOND states, the endpoint correctly reponds with Reset, while in the REQUEST/OPEN states, packets with option errors are just ignored. The packet sequence is as follows: Case 1: Endpoint A Endpoint B (CLOSED) (CLOSED) <---------------- REQUEST RESPONSE -----------------> (*1) (with invalid option) <---------------- RESET (with Reset Code 5, "Option Error") (*1) currently just ignored, no Reset is sent Case 2: Endpoint A Endpoint B (OPEN) (OPEN) DATA-ACK -----------------> (*2) (with invalid option) <---------------- RESET (with Reset Code 5, "Option Error") (*2) currently just ignored, no Reset is sent This patch fixes the problem, by generating a Reset instead of silently ignoring option errors. Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com> Acked-by: NArnaldo Carvalho de Melo <acme@redhat.com> Acked-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
-
由 Simon Horman 提交于
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/lvs-2.6 into lvs-next-2.6
-
由 Julius Volz 提交于
After integrating ESP into ip_vs_proto_ah, rename it (and the references to it) to ip_vs_proto_ah_esp.c and delete the old ip_vs_proto_esp.c. Signed-off-by: NJulius Volz <juliusv@google.com> Signed-off-by: NSimon Horman <horms@verge.net.au>
-
由 Julius Volz 提交于
Rename all ah_* functions to ah_esp_* (and adjust comments). Move ESP protocol definition into ip_vs_proto_ah.c and remove all usage of ip_vs_proto_esp.c. Make the compilation of ip_vs_proto_ah.c dependent on a new config variable, IP_VS_PROTO_AH_ESP, which is selected either by IP_VS_PROTO_ESP or IP_VS_PROTO_AH. Only compile the selected protocols' structures within this file. Signed-off-by: NJulius Volz <juliusv@google.com> Signed-off-by: NSimon Horman <horms@verge.net.au>
- 23 8月, 2008 3 次提交
-
-
由 Ilpo Järvinen 提交于
Some duplicated code lying around. Located with my suffix tree tool. Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ilpo Järvinen 提交于
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ilpo Järvinen 提交于
Large block of code duplication removed. Sadly, the return value thing is a bit tricky here but it seems the most sensible way to return positive from validator on success rather than negative. Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-