Zen Kato's device has a regulatory domain value of 0x49, which is not an
IEEE 802.11 code and is not even identified in the vendor driver.

Recent versions of the vendor driver don't even look at the regdomain
value any more, and just allow channels 1-11 everywhere. This patch
brings us more in line with that behaviour, by allowing channels 1-11
for regdomains which we don't know about.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't turn the radio on until the interface is up. This saves some power in
case the driver is loaded but the card is not used.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Callers of enable_MAC() shouldn't have to worry about the bits in the
response's status word (and most of them don't). The return value is
sufficient information.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Matteo Croce reported Aironet initialization failures. They were caused by
a race in airo. airo finds a free interface name, then initializes the card
and finally registers the interface. Another device may get the same name
in the meantime.
The reason airo gets its name early is to use it in informative printks and
to name the resources it requests. The printks will be just fine without
the interface name and the resources can use the driver's name - that's
what other network drivers do anyway.
One of the talkative functions is setup_card(). It is called once before
registration and can be called later again. Let's have an empty dev->name
during the first call, so it doesn't print the ugly "airo(eth%d)" message.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

airo's kernel thread and the IRQ handler are needed only when the interface
is up.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix an assymetry between pci_{enable,disable}_device. airo did not disable
the PCI device when unloading the module. This caused suspend failures
after modprobe -r airo && modprobe airo.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Similar patch to ipw2200. Round the timer used for RF kill
switch off to 1 second boundary to save power.
Build tested only, don't have this hardware.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make the ipw2200 driver polling of rf kill switch occur on second boundaries to reduce
power. Making all the wakeup's in the system occur together reduces power, and keeps
CPU in idle longer.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I failed to notice that a u16 was being passed to the hardware.
This fixes it.

Thanks to Kasper F. Brandt for finding this!
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

... by removing an ill-conceived, useless line.  Discovered by coverity.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove a header file that was ostensibly "removed" before, in commit
3ce40232.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (31 commits)
  firewire: fw-sbp2: fix DMA mapping of management ORBs
  firewire: fw-sbp2: fix DMA mapping of command ORBs
  firewire: fw-sbp2: fix DMA mapping of S/G tables
  firewire: fw-sbp2: add a boundary check
  firewire: fw-sbp2: correctly align page tables
  firewire: fw-sbp2: memset wants string.h
  firewire: fw-sbp2: use correct speed in sbp2_agent_reset
  firewire: fw-sbp2: correctly dereference by container_of
  firewire: Document userspace ioctl interface.
  firewire: fw-sbp2: implement nonexclusive login
  firewire: fw-sbp2: let SCSI shutdown commands through before logout
  firewire: fw-sbp2: implement max sectors limit for some old bridges
  firewire: simplify a struct type
  firewire: support S100B...S400B and link slower than PHY
  firewire: optimize gap count with 1394b leaf nodes
  firewire: remove unused macro
  firewire: missing newline in printk
  firewire: fw-sbp2: remove unused struct member
  ieee1394: remove old isochronous ABI
  ieee1394: sbp2: change some module parameters from int to bool
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: handle cases of volume knobs generating relative values
  HID: Logitech keyboard 0xc311 needs reset leds quirk
  HID: support for logitech cordless desktop LX500 special mapping
  HID: fix autocentering of PID devices
  HID: separate quirks for report descriptor fixup
  HID: Add NOGET quirk for all NCR devices
  HID: support for Petalynx Maxter remote control
  HID: fix mismatch between hid-input HUT find/search mapping and the HUT
  HID: support for Gameron dual psx adaptor
  USB HID: avoid flush_scheduled_work()
  HID: Use menuconfig objects
  HID: force hid-input for Microsoft SideWinder GameVoice device
  HID: input mapping for Chicony KU-0418 tactical pad
  HID: make debugging output runtime-configurable

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (75 commits)
  Ethernet driver for EISA only SNI RM200/RM400 machines
  Extract chip specific code out of lasi_82596.c
  ehea: Whitespace cleanup
  pasemi_mac: Fix TX interrupt threshold
  spidernet: Replace literal with const
  r8169: perform RX config change after mac filtering
  r8169: mac address change support
  r8169: display some extra debug information during startup
  r8169: add endianess annotations to [RT]xDesc
  r8169: align the IP header when there is no DMA constraint
  r8169: add bit description for the TxPoll register
  r8169: cleanup
  r8169: remove the media option
  r8169: small 8101 comment
  r8169: confusion between hardware and IP header alignment
  r8169: merge with version 8.001.00 of Realtek's r8168 driver
  r8169: merge with version 6.001.00 of Realtek's r8169 driver
  r8169: prettify mac_version
  r8169: populate the hw_start handler for the 8110
  r8169: populate the hw_start handler for the 8168
  ...

The CPU must not touch the buffer after it was DMA-mapped.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

The CPU must not touch the buffer after it was DMA-mapped.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

  - The CPU must not touch the buffer after it was DMA-mapped.
  - The size argument of dma_unmap_single(...page_table...) was bogus.
  - Move a comment closer to the code to which it refers to.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Add rudimentary check for the case that the page table overflows due to
merging of s/g elements by the IOMMU.  This would have lead to
overwriting of arbitrary memory.

After this change I expect that an offending command will be
unsuccessfully retried until the scsi_device is taken offline by SCSI
core.  It's a border case and not worth to implement a recovery
strategy.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

This is required per SBP-2 clause 5.2.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

noticed by Jay Fenlason
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

Replace a cast with a container_of().  As long as nobody reorders the
structure elements, they do the same thing, but container_of() is more
readable.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added complete_command_orb)
Acked-by: NKristian Høgsberg <krh@redhat.com>

The isochronous packet format is still not documented, but this
is a good first step.
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (format, wording)

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

This affects of course only the "soft shutdown" case, e.g. "modprobe -r
firewire-sbp2", while it doesn't matter for hot unplug.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

This currently only affects one bridge in the hardwired blacklist.
I don't own one of those, hence haven't tested it.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

cleanup after "firewire: support S100B...S400B and link slower than PHY"
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Use a speed probe to determine the speed over 1394b buses and of nodes
which report a link speed less than their PHY speed.

Log the effective maximum speed of newly created nodes in dmesg.

Also, read the config ROM (except bus info block) at the maximum speed
rather than S100.  This isn't a real optimization though because we
still only use quadlet read requests for the entire ROM.

The patch also adds support for S1600 and S3200, although such hardware
does not exist yet.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Table-based gap count optimization cannot be used if 1394b repeater PHYs
are present.  But it does work with 1394b leaf nodes.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Also remove some errno printouts which will be shown by infrastructure
code anyway.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

cleanup after support of single-buffer requests was dropped
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Hoegsberg <krh@redhat.com>

Based on patch "the scheduled removal of RAW1394_REQ_ISO_{SEND,LISTEN}"
from Adrian Bunk, November 20 2006.

This patch also removes the underlying facilities in ohci1394 and
disables them in pcilynx.  That is, hpsb_host_driver.devctl() and
hpsb_host_driver.transmit_packet() are no longer used for iso reception
and transmission.

Since video1394 and dv1394 only work with ohci1394 and raw1394's rawiso
interface has never been implemented in pcilynx, pcilynx is now no
longer useful for isochronous applications.

raw1394 will still handle the request types but will complete the
requests with errors that indicate API version conflicts.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This is upwards compatible, except that integer values other than 0 or 1
are no longer accepted.  But values like "Y", "N", "no", "nnoooh!" work
now.

Also, improve a comment on the serialize_io parameter and make the
ORB_SET_EXCLUSIVE macro ultra-safe.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Association of a host device with a node on NUMA machines optimizes
allocations of skbs given from the networking stack to eth1394.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

After ieee1394 was converted away from class_device like the networking
subsystem was already in 2.6.21, eth1394's device may point to the
fw-host device as its parent again like in 2.6.20.

This affects userspace tools which examine the sysfs representation of
eth1394's device.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Remove the global nodemgr_serialize mutex which enclosed most of the
host thread event loop.  This allows for parallelism between several
host adapter cards.

Properly serialize the driver hooks .update(), .suspend(), .resume(),
and .remove() by means of device->sem.  These hooks can be called from
outside the host threads' contexts.

Get() and put() the device.driver when calling its hooks.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Here is a straightforward conversion to "struct device". The "struct
class_device" will be removed from the kernel.

It seems to work fine for me with and without CONFIG_SYSFS_DEPRECATED
set.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

I was told that only i386 aligns 64 bit integers at 4 bytes boundaries
while all other architectures (32 bit architectures with 64 bit
siblings) align it on 8 bytes boundaries.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Pointed out by Arnd Bergmann:  PPC32 aligns this at 64bit, IA32 packs
it.  A kernel-wide available __compat_u64 which is 4-byte aligned on
AMD64 and IA64 would be nicer though.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>