- 12 1月, 2008 2 次提交
-
-
由 Olaf Kirch 提交于
Rewrite recv path. Fixes: - data digest processing and error handling. - ahs support. Some fixups by Mike Christie Signed-off-by: NOlaf Kirch <olaf.kirch@oracle.com> Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
由 Mike Christie 提交于
This patch adds logical unit reset support. This should work for ib_iser, but I have not finished testing that driver so it is not hooked in yet. This patch also temporarily reverts the iscsi_tcp r2t write out patch. That code is completely rewritten in this patchset. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
- 16 8月, 2007 1 次提交
-
-
由 Mike Christie 提交于
The iscsi eh could be tearing down the session/connection while the scsi eh is still sending task management functions. If when we drop the session lock to grab the recv lock, the iscsi eh tears down the connection we will oops. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 27 7月, 2007 1 次提交
-
-
由 Mike Christie 提交于
We should not be checking the cmd windown for just handling r2t responses. And if the window closes in on us, always have scsi-ml requeue the command from our queuecommand function. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 03 6月, 2007 4 次提交
-
-
由 Mike Christie 提交于
iSCSI must support software iscsi (iscsi_tcp, iser), hardware iscsi (qla4xxx), and partial offload (broadcom). To be able to allow each stack or driver or port (virtual or physical) to be able to log into the same target portal we use the initiator tuple [[HWADDRESS | NETDEVNAME], INITIATOR_NAME] and the target tuple [TARGETNAME, CONN_ADDRESS, CONN_PORT] to id a session. This patch adds the netdev name, which is used by software iscsi when it binds a session to a netdevice using the SO_BINDTODEVICE sock opt. It cannot use HWADDRESS because if someone did vlans then the same netdevice will have the same mac and the initiator,target id will not be unique. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Cc: Roland Dreier <rdreier@cisco.com> Cc: David C Somayajulu <david.somayajulu@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mike Christie 提交于
This patch exports the local address for the session. For qla4xxx this is the ip of the hba's port. For software this is the src addr of the socket. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Cc: David C Somayajulu <david.somayajulu@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mike Christie 提交于
This patch allows us to set can_queue and cmds_per_lun from userspace when we create the session/host. From there we can set it on a per target basis. The patch fully converts iscsi_tcp, but only hooks up ib_iser for cmd_per_lun since it currently has a lots of preallocations based on can_queue. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Cc: Roland Dreier <rdreier@cisco.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mike Christie 提交于
The cmdsn allocation and pdu transmit code can race, and we can end up sending a pdu with cmdsn 10 before a pdu with 5. The target will then fail the connection/session. This patch fixes the problem by delaying the cmdsn allocation until we are about to send the pdu. This also removes the xmitmutex. We were using the connection xmitmutex during error handling to handle races with mtask and ctask cleanup and completion. For ctasks we now have nice refcounting and for the mtask, if we hit the case where the mtask timesout and it is floating around somewhere in the driver, we end up dropping the session. And to handle session level cleanup, we use the xmit suspend bit along with scsi_flush_queue and the session lock to make sure that the xmit thread is not possibly transmitting a task while we are trying to kill it. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Cc: Roland Dreier <rdreier@cisco.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 02 6月, 2007 5 次提交
-
-
由 Mike Christie 提交于
The attached patches add sysfs files for the chap settings to the iscsi transport class, iscsi_tcp and ib_iser. This is needed for software iscsi because there are times when iscsid can die and it will need to reread the values it was using. And it is needed by qla4xxx for basic management opertaions. This patch does not hook in qla4xxx yet, because I am not sure the mbx command to use. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Cc: Roland Dreier <rdreier@cisco.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mike Christie 提交于
- Remove shadow of request length from struct iscsi_cmd_task. - change all users to use scsi_cmnd->request_bufflen directly (With bidi we will use scsi-ml API to retrieve in/out length) Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com> Signed-off-by: NBenny Halevy <bhalevy@panasas.com> Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Cc: Roland Dreier <rdreier@cisco.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mike Christie 提交于
This patch fixes handling of expected datasn/r2tsn as received from target. It is done according to: T10 rfc3720 section 3.2.2.3. Data Sequencing. . unify expected datasn/r2tsn into one counter . calculate than check expected datasn/r2tsn. On error print a message and fail the request. (TODO use iscsi retransmits) . remove the FIXME ;) . avoid zero length memset Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com> Signed-off-by: NBenny Halevy <bhalevy@panasas.com> Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mike Christie 提交于
For iscsi root boot, software iscsi needs to know what the BIOS/OF initiator used for the initiator name so this puts it in sysfs for userspace to be able to pick up. For hw iscsi, it is nice to see what the card is using. This patch adds the new param, and hooks in qla4xxx, iscsi_tcp, and ib_iser. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Cc: Roland Dreier <rdreier@cisco.com> Cc: David C Somayajulu <david.somayajulu@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mike Christie 提交于
iscsid and udev need to key off the hw address being used so add some helpers for iser and iscsi tcp. Also convert them Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Cc: Roland Dreier <rdreier@cisco.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 04 12月, 2006 1 次提交
-
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
-
- 26 10月, 2006 1 次提交
-
-
由 Mike Christie 提交于
If connection creation fails we end up calling list_del on a invalid struct. This then causes an oops. We are not acutally using the lists (old MCS code we thought might be useful elsewhere) so this patch just removes that code. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 03 9月, 2006 2 次提交
-
-
由 Mike Christie 提交于
It is possible that a ctask could be completing and getting cleaned up at the same time, we are finishing up the last data transfer. This could then result in the data transfer code using stale or invalid values. This patch adds a refcount to the ctask. When the count goes to zero then we know the transmit thread and recv thread or softirq are not touching it and we can safely release it. The eh should not need to grab a reference because it only cleans up a task if it has both the xmit mutex and recv lock (or recv side suspended). Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mike Christie 提交于
iSCSI RFC states that the first burst length must be smaller than the max burst length. We currently assume targets will be good, but that may not be the case, so this patch adds a check. This patch also moves the unsol data out offset to the lib so the LLDs do not have to track it. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 29 7月, 2006 3 次提交
-
-
由 Mike Christie 提交于
We currently try to allocate a max_recv_data_segment_length which can be very large (default is 64K), and common uses are up to 1MB. It is very very difficult to allocte this much contiguous memory and it turns out we never even use it. We really only need a couple of pages, so this patch has us allocates just what we know what we need today. Later if vendors start adding vendor specific data and we need to handle large buffers we can do this, but for the last 4 years we have not seen anyone do this or request it. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mike Christie 提交于
Abort handler fixes. If a connection is dropped and reconnected while an abort is running then we should assume the recovery code will clean up the abort. Not doing so causes a oops. And if a command completes then we get the status for the abort, we do not need to call into the LLD to cleanup the resources. Doing this causes and oops in iser because it ends up freeing some resources twice. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mike Christie 提交于
The iscsi tcp code can pluck multiple rt2s from the tasks's r2tqueue in the xmit code. This can result in the task being queued on the xmit queue but gettting completed at the same time. This patch fixes the above bug by making the fifo a list so we always remove the entry on the list del. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 29 6月, 2006 1 次提交
-
-
由 Mike Christie 提交于
Reduce duplication in the software iscsi_transport modules by adding a libiscsi function to handle the common grunt work. This also has the drivers return specifc -EXXX values for different errors so userspace can finally handle them in a sane way. Also just pass the sysfs buffers to the drivers so HW iscsi can get/set its string values, like targetname, and initiatorname. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 06 6月, 2006 1 次提交
-
-
由 Mike Christie 提交于
If recovery failed or we are in recovery only overwrite the state if we are going to terminate the session or if we logged back in. STOP_CONN_SUSPEND and conn_cnt are not used. We only support a single connection session ATM, so cleanup that code while we are working around it. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 20 5月, 2006 1 次提交
-
-
由 Mike Christie 提交于
Do not flush queues then block session. This will cause commands to needlessly swing around on us and remove goofy recovery_failed field and replace with state value. And do not start recovery from within the host reset function. This causeis too many problems becuase open-iscsi was desinged to call out to userspace then have userpscae decide if we should go into recovery or kill the session. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 10 5月, 2006 1 次提交
-
-
由 Or Gerlitz 提交于
align printk output Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com> Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 15 4月, 2006 1 次提交
-
-
由 Mike Christie 提交于
There is a lot of code duplcited between iscsi_tcp and the upcoming iscsi_iser driver. This patch puts the duplicated code in a lib. There is more code to move around but this takes care of the basics. For iscsi_offload if they use the lib we will probably move some things around. For example in the queuecommand we will not assume that the LLD wants to do queue_work, but it is better to handle that later when we know for sure what iscsi_offload looks like (we could probably do this for iscsi_iser though to). Ideally I would like to get the iscsi_transports modules to a place where all they really have to do is put data on the wire, but how to do that will hopefully be more clear when we see other modules like iscsi_offload. Or maybe iscsi_offload will not use the lib and it will just be iscsi_iser and iscsi_tcp and maybe the iscsi_tcp_tgt if that is allowed in mainline. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-