- 24 10月, 2015 19 次提交
-
-
由 Bhupesh Sharma 提交于
This patch updates the LS2080a DTSI (DTS Include) file to add support for the following peripherals: - USB 3.0 Host - PMU - CCN-504 - SATA - SPI - PCIe Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: NJaiprakash Singh <b44839@freescale.com> Signed-off-by: NAlison Wang <alison.wang@freescale.com> Signed-off-by: NLiu Gang <Gang.Liu@freescale.com> Signed-off-by: NMinghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com> Signed-off-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Bhupesh Sharma 提交于
Since the Synopsys DWC3 controller driver inherits the generic bindings defined in 'usb/generic.txt', this patch tries to capture the same in the DWC3 binging documentation to avoid any confusion in usage of properties like 'dr_mode' for certain SoCs like FSL LS2080A. Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Bhupesh Sharma 提交于
Update the FSL, GPIO binding documentation to add support for GPIO controller found on Freescale's LS2080A platform. Signed-off-by: NLiu Gang <Gang.Liu@freescale.com> Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Bhupesh Sharma 提交于
Since the same board components can be used across ARM and PPC board families, this patch moves the FSL board-specific bindings out of bindings/powerpci. While at it, this patch also adds the bindings for QIXIS FPGA controller found on FSL LS2080A boards. These boards have an on-board FPGA/CPLD connected to the IFC controller. Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: NJaiprakash Singh <b44839@freescale.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Bhupesh Sharma 提交于
This patch adds a devicetree binding documentation for Freescale's LS2080A QDS and RDB boards. Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Bhupesh Sharma 提交于
Freescale is renaming the LS2085A SoC to LS2080A. This patch addresses the same. Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Bhupesh Sharma 提交于
Freescale will be a spinning-out a set of ARMv8 based SoCs which will be based on a similar overall SoC architecture. So, this patch converts the existing infrastructure in the arm64/dts, arm64/Kconfig and arm64/configs to use the generic convention ARCH_LAYERSCAPE in place of the more specific FSL_LS2085A, to save code duplication later-on. Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Arnd Bergmann 提交于
Merge tag 'at91-ab-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt Merge "Second batch of DT changes for 4.4" from Alexandre Belloni: - some DT fixes: pullups, disabled property - the PMC is now a syscon - great improvement of sama5d2 support * tag 'at91-ab-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: ARM: at91/dt: sama5d2: add missing devices ARM: at91/dt: sama5d4: add the macb1 node ARM: at91/dt: add pullup on mmc2 data signals ARM: at91/dt: sama5d2_xplained: add regulator nodes ARM: at91/dt: fix "disabled" property on at91rm9200 ARM: at91/dt: use syscon for PMC
-
由 Arnd Bergmann 提交于
Merge tag 'omap-for-v4.4/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt Merge "omap dts changes for v4.4 merge window, part 2" from Tony Lindgren: Few more omap dts changes for v4.4 merge window, mostly to fix and clean up some omap5 issues to allow adding other omap5 boards. Also some other fixes and clean-up: - Fix SDIO WLAN for omap5 that's been broken for a while. As further patches are still needed for wl18xx, no need for stable on this one. - Move most of omap5 support into omap5-board-common.dtsi as most omap5 boards seem to share the same basic set of devices. - Add minimal IGEPv5 support using based on omap5-board-common.dtsi - Remove now unneedes gpio hogging for dra72-evm - Update Javier Martinez Canillas email address - Change earlier IGEP boards to use IOPAD pinmux macros * tag 'omap-for-v4.4/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: am335x-base0033: Use IOPAD pinmux macro ARM: dts: am335x-igep0033: Use IOPAD pinmux macro ARM: dts: omap3-igep0020: Use IOPAD pinmux macro ARM: dts: am437x-gp-evm: Add wakeup interrupt source for pixcir_i2c_ts ARM: dts: Update Javier Martinez Canillas's email ARM: dts: dra72-evm: remove cpsw gpio hogging and add mode-gpios ARM: dts: Add basic support for isee igepv5 ARM: dts: Move most of omap5-uevm.dts to omap5-board-common.dtsi ARM: dts: Fix WLAN regression on omap5-uevm
-
由 Masahiro Yamada 提交于
Initial version of DTS for ProXstream2 Vodka board. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Masahiro Yamada 提交于
Initial version of DTS for ProXstream2 Gentil board. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Masahiro Yamada 提交于
Specifying both console and stdout-path is redundant. Add options ":115200n8" to stdout-path and drop "console=ttyS0,115200". Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Arnd Bergmann 提交于
Merge tag 'sti-dt-for-v4.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti into next/dt Merge "STi DT changes for v4.4, round 2" from Maxime Coquelin: - Use STiH418's A9 PLL - Add Ethernet support to STiH407 family * tag 'sti-dt-for-v4.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti: ARM: STi: DT: Add support for stih418 A9 pll ARM: dts: Enable Ethernet on STi's B2199 board ARM: dts: Enable Ethernet on STi's B2120 boards ARM: dts: Add Ethernet node to STiH407 family ARM: dts: Fix RGMII pinctrl timings
-
由 Vladimir Zapolskiy 提交于
The change corrects cpu compatible property to a defined one, see Documentation/devicetree/bindings/arm/cpus.txt Signed-off-by: NVladimir Zapolskiy <vz@mleia.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Vladimir Zapolskiy 提交于
The change corrects cpu compatible property to a defined one, see Documentation/devicetree/bindings/arm/cpus.txt Signed-off-by: NVladimir Zapolskiy <vz@mleia.com> Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux由 Olof Johansson 提交于
The i.MX device tree changes for 4.4: - Add IOMUXC LPSR (Low Power State Retention) device for i.MX7D. - Add a few low power mode related devices and touch controller for i.MX6UL. - Add a number of devices for i.MX7D SDB board support, USB, Dual FEC, and eMMC5.0. - i.MX6 Boundary Devices updates: relicense under GPLv2/X11, add Okaya LCD, touch and wifi support, add new boards Nitrogen6_Lite and Nitrogen6_Max. - Enable touch screen and NAND Flash controller for a few Vybrid devices. - Some random and small updates on LS1021A and MXS support. * tag 'imx-dt-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (53 commits) ARM: dts: ls1021a: Add quirk for Erratum A009116 ARM: imx6sx-sdb: Fix typo in regulator enable GPIO property ARM: dts: imx6: phyFLEX: fix typo in "pinctrl-names" ARM: dts: imx6: change the core clock of spdif ARM: dts: vf-colibri: enable NAND flash controller ARM: dts: vf610twr: add NAND flash controller peripherial ARM: dts: imx: add Boundary Devices Nitrogen6_Lite board ARM: dts: imx: add Boundary Devices Nitrogen6_Max board ARM: dts: imx6dl-nitrogen6x: change manufacturer to Boundary Devices ARM: dts: imx6q-nitrogen6x: change manufacturer to Boundary Devices of: Add Boundary Devices Inc. vendor prefix ARM: dts: imx6qdl-sabrelite: relicense under GPLv2/X11 ARM: dts: imx6qdl-nitrogen6x: relicense under GPLv2/X11 ARM: dts: imx6qdl-nitrogen6x: add wifi wl1271 support ARM: dts: imx6dql-nitrogen6x: add touchscreen support ARM: dts: imx6qdl-sabrelite: add Okaya LCD panel ARM: dts: imx6qdl-nitrogen6x: add Okaya LCD panel ARM: dts: vf500-colibri: Add device tree node for touchscreen support ARM: dts: i.MX35: fix cpu compatible value ARM: dts: i.MX31: fix cpu compatible value ... Signed-off-by: NOlof Johansson <olof@lixom.net>
-
https://github.com/mbgg/linux-mediatek由 Olof Johansson 提交于
Delete regulator-compatible usage in mt8135-evbp1.dts. The regualtor-compatible binding is deprecated, instead the node name is used. Mediatek timer driver supports as well mt8127, mt8135 and mt8173. Add these SOCs to the bindings list. Power domains venc and venc_lt need clocks two extra clocks to access their registers. We update the bindings documentation about this. Update SMP bindings documentation by adding support for mt6589 and mt81xx SOCs. Update mt8127.dtsi and mt8135.dtsi to enable SMP support. * tag 'v4.3-next-dts' of https://github.com/mbgg/linux-mediatek: ARM: dts: mt8127: enable basic SMP bringup for mt8127 ARM: dts: mt8135: enable basic SMP bringup for mt8135 devicetree: bindings: add new SMP enable method Mediatek SoC dt-bindings: soc: Add clocks for Mediatek SCPSYS unit dt-bindings: add more MediaTek SoC to mtk-timer binding ARM: dts: mt8135-evbp1: remove regulator-compatible usage Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Olof Johansson 提交于
Merge tag 'v4.4-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt SPDIF device nodes for the newly added driver. * tag 'v4.4-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: ARM: dts: rockchip: Add SPDIF optical out on Radxa Rock2 Square ARM: dts: rockchip: Add SPDIF transceiver for RK3288 ARM: dts: rockchip: Add SPDIF optical out on Radxa Rock ARM: dts: rockchip: Add SPDIF transceiver for RK3188 Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Olof Johansson 提交于
Merge tag 'sunxi-dt-for-4.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt Allwinner DT changes for 4.4, round 2 More DT patches for 4.4, mostly with new boards coming in (CHIP, BananaPi M2, pcduino2), further consolidation for the q8-based designs and a bunch of random patches enhancing support for existing boards * tag 'sunxi-dt-for-4.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (27 commits) ARM: dts: sun6i: Add a dts file for the Sinovoip BPI-M2 board ARM: dts: sun6i: Add mmc2_pins_a pinmux setting to sun6i-a31.dtsi ARM: dts: sunxi: Fix interrupt-cells for [r]pio on A23/A31/A33/A80 ARM: dts: sun8i: Add NMI interrupt controller node ARM: dts: sun6i: hummingbird: Enable AXP221 DC5LDO regulator as "vdd-cpus" ARM: dts: sun6i: hummingbird: Use axp22x.dtsi for AXP221 regulators ARM: dts: sun6i: hummingbird: Fix VDD-CPU and VDD-GPU regulator names ARM: dts: sun7i: Add regulator configuration for pcDuino v3 Nano ARM: dts: sun6i: Turn on gmac on Colombus ARM: dts: sun8i: Make et-q8-v1.6.dts a symlink to q8-tablet.dts ARM: dts: sun8i: Make ippo-q8h-v*.dts a symlink to q8-tablet.dts ARM: dts: sun8i: Add sun8i-a23-q8-tablet.dts file ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi ARM: dts: sunxi: Enable PWM controller on Q8 format tablets ARM: dts: sun5i: Add PWM channel 0 pinmux setting for A13/A10s ARM: dts: sun5i: Add PWM controller node for A13 / A10s ARM: sun5i: Add C.H.I.P DTS ARM: dts: sunxi: Add dtsi for AXP22x PMIC ARM: dts: sun7i: Correct USB regulators on pcDuino v3 Nano ARM: sun5i: dt: Add UART3 CTS and RTS pins ... Signed-off-by: NOlof Johansson <olof@lixom.net>
-
- 23 10月, 2015 3 次提交
-
-
git://git.infradead.org/linux-mvebu由 Olof Johansson 提交于
mvebu dt for 4.4 (part 2) - Add support for severals Armada-370-based Seagate NAS - Fix Ready NAS device tree - Modify SDHCI binding for A388-GP allowing using it on old and new version of the board * tag 'mvebu-dt-4.4-2' of git://git.infradead.org/linux-mvebu: ARM: mvebu: set SW polling as SDHCI card detection on A388-GP arm: mvebu: reorder nodes under internal-regs by address in RN2120 .dts file arm: mvebu: disable unused Armada RTC on ReadyNAS 102, 104 and 2120 ARM: mvebu: add DT support for Seagate Personal Cloud ARM: mvebu: add DT support for Seagate NAS 2 and 4-Bay Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Olof Johansson 提交于
Merge tag 'socfpga_for_v4.4_cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt SoCFPGA dts cleanup for v4.4 - Re-order DTS nodes into correct alphabetical order * tag 'socfpga_for_v4.4_cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: ARM: socfpga: dts: sort nodes alphabetically Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Olof Johansson 提交于
Merge tag 'socfpga_dts_for_v4.4_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt SoCFPGA DTS update for v4.4, part 2 - Add the FPGA manager node * tag 'socfpga_dts_for_v4.4_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: ARM: socfpga: dts: add fpga manager Signed-off-by: NOlof Johansson <olof@lixom.net>
-
- 21 10月, 2015 6 次提交
-
-
由 Javier Martinez Canillas 提交于
Use the AM33XX pinmux IOPAD macro to define the physical address instead of the offset from the padconf address. It makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Javier Martinez Canillas 提交于
Use the AM33xx pinmux IOPAD macro to define the physical address instead of the offset from the padconf address. It makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Javier Martinez Canillas 提交于
Use the OMAP3 pinmux IOPAD macro to define the physical address instead of the offset from the padconf address. It makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Vignesh R 提交于
On am437x-gp-evm, pixcir_i2c_ts can wakeup the system from low power state via pinctrl and IO daisy chain using generic wakeirq framework. With commit 3fffd128 ("i2c: allow specifying separate wakeup interrupt in device tree") i2c core allows optional wakeirq to be specified via device tree. Add wakeup irq entry to enable pixcir_i2c_ts to wake the system from low power state. Signed-off-by: NVignesh R <vigneshr@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Javier Martinez Canillas 提交于
I see that people are still sending emails to my old address (that no longer exists) since is the one mentioned in the IGEP DTS. Replace it with my current email address to avoid this. Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Mugunthan V N 提交于
With the current implementation of GPIO hogging and with gpio-pcf857x is built as module, ethernet doesn't work on boot and doesn't throw any error/warning to user. Ethernet becomes operational when inserting gpio-pcf857x module, even this time there is no error/warning logs to user that ethernet is operational. When using with NFS rootfs and gpio-pcf857x as module, board doesn't boot as it doesn't get any ip address and doesn't throw any error/warning. To over come this, now cpsw driver tries to get mode-gpios. When gpio-pcf857x is built as module it will throw error, so that user can decide either to built in gpio-pcf857x to continue with nfs boot or choose alternate rootfs filesystem like sd/ramdisk. When using mmc/ramdisk as root fs, cpsw will probe defer and re-probes again when gpio-pcf857x module is inserted and ethernet becomes operational. Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 20 10月, 2015 1 次提交
-
-
由 Ludovic Desroches 提交于
Big update of the sama5d2.dtsi file since many patches have reached te mainline: - add generated clocks - enable crypto devices - add flexcom devices - add tdes device - add sdmmc devices Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com> Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
-
- 19 10月, 2015 11 次提交
-
-
由 Gregory CLEMENT 提交于
The second macb is present on all the sama5d4 SoCs. Let's add a node reflecting it in the device tree. Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
-
由 Sylvain Rochet 提交于
MMC data lines may be left floating if nothing is currently driving the data lines, which is the case when mmc is in idle state, thus consuming a useless extra amount of power. Add pullup on mmc2 data signals in the same way it was previously done for mmc0 and mmc1. Signed-off-by: NSylvain Rochet <sylvain.rochet@finsecur.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
-
由 Wenyou Yang 提交于
Add regulator nodes of PMIC ACT8945A chip on the board. Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com> Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
-
由 Michael Opdenacker 提交于
Fix instances of "disable" instead of "disabled" in the at91rm9200 dtsi. Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com> Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
-
由 Alexandre Belloni 提交于
The PMC is not only used to drive the clocks but also has some registers related to other functions. One of those is for example the USB gadget bias. Using a syscon allows to properly separate those functions. Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
-
由 Rajesh Bhagat 提交于
Add "snps,quirk-frame-length-adjustment" property to USB3 node for erratum A009116. This property provides value of GFLADJ_30MHZ for post silicon frame length adjustment. Signed-off-by: NNikhil Badola <nikhil.badola@freescale.com> Signed-off-by: NRajesh Bhagat <rajesh.bhagat@freescale.com> Signed-off-by: NShawn Guo <shawnguo@kernel.org>
-
由 Laurent Pinchart 提交于
The property name should be "gpio", not "gpios". Fix it. Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NShawn Guo <shawnguo@kernel.org>
-
由 Michael Opdenacker 提交于
Fix a typo, replacing "pinctrl-name" by "pinctrl-names" in the Phytec phyFLEX-i.MX6 Quad dtsi. Also fix a typo in the board name Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com> Signed-off-by: NShawn Guo <shawnguo@kernel.org>
-
由 Shengjiu Wang 提交于
The correct core clock of spdif is SPDIF_GCLK, which is added to clock tree. So the dts also need to be updated. Signed-off-by: NShengjiu Wang <shengjiu.wang@freescale.com> Signed-off-by: NShawn Guo <shawnguo@kernel.org>
-
由 Stefan Agner 提交于
Enable NAND access by adding pinmux and NAND flash controller node to device tree. The NAND chips currently used on the Colibri VF61 requires 8-bit ECC per 512 byte page, hence specify 32-bit ECC strength per 2k page size. Reviewed-by: NBrian Norris <computersforpeace@gmail.com> Signed-off-by: NStefan Agner <stefan@agner.ch> Signed-off-by: NShawn Guo <shawnguo@kernel.org>
-
由 Stefan Agner 提交于
This adds the NAND flash controller (NFC) peripherial. The driver supports the SLC NAND chips found on Freescale's Vybrid Tower System Module. The Micron NAND chip on the module needs 4-bit ECC per 512 byte page. Use 24-bit ECC per 2k page, which is supported by the driver. Signed-off-by: NBill Pringlemeir <bpringlemeir@nbsps.com> Reviewed-by: NBrian Norris <computersforpeace@gmail.com> Signed-off-by: NStefan Agner <stefan@agner.ch> Signed-off-by: NShawn Guo <shawnguo@kernel.org>
-