Merge tag 'keystone-reset-driver' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/drivers

Merge "Keystone Reset driver for 3.16" from Santosh Shilimkar:

* tag 'keystone-reset-driver' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  power: reset: keystone-reset: introduce keystone reset driver
  Documentation: dt: add bindings for keystone pll control controller
  Documentation: dt: add bindings for keystone reset driver
Signed-off-by: NOlof Johansson <olof@lixom.net>

The keystone SoC can be rebooted in several ways. By external reset
pin, by soft and by watchdogs. To allow keystone SoC reset if
watchdog is triggered we have to enable it in reset mux configuration
register regarding of watchdog configuration. Also we need to set
soft/hard reset we are going to use.

So add keystone reset driver to handle all this stuff.
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

The main pll controller used to drive theC66x CorePacs, the switch fabric,
and a majority of the peripheral clocks (all but the ARM CorePacs, DDR3 and
the NETCP modules) requires a PLL Controller to manage the various clock
divisions, gating, and synchronization.
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>
[santosh.shilimkar@ti.com: Fixed the subject line]
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

This node is intended to allow SoC reset in case of software reset
or appropriate watchdogs.

The Keystone SoCs can contain up to 4 watchdog timers to reset
SoC. Each watchdog timer event input is connected to the Reset Mux
block. The Reset Mux block can be configured to cause reset or not.

Additionally soft or hard reset can be configured.
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>
[santosh.shilimkar@ti.com: Fixed the subject line]
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Merge tag 'davinci-for-v3.16/edma' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers

Merge "DaVinci EDMA clean-up for v3.16" from Sekhar Nori:

This series makes edma use configuration information available within
the IP instead of reading it from platform data or DT. Some other useful
clean-ups are included too.

* tag 'davinci-for-v3.16/edma' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: (34 commits)
  ARM: edma: Remove redundant/unused parameters from edma_soc_info
  ARM: davinci: Remove redundant/unused parameters for edma
  ARM: dts: am4372: Remove obsolete properties from edma node
  ARM: dts: am33xx: Remove obsolete properties from edma node
  dt/bindings: ti,edma: Remove redundant properties from documentation
  ARM: edma: Get IP configuration from HW (number of channels, tc, etc)
  ARM: edma: Save number of regions from pdata to struct edma
  ARM: edma: Remove num_cc member from struct edma
  ARM: edma: Remove queue_tc_mapping data from edma_soc_info
  ARM: davinci: Remove eDMA3 queue_tc_mapping data from edma_soc_info
  ARM: edma: Do not change TC -> Queue mapping, leave it to default.
  ARM: edma: Take the number of tc from edma_soc_info (pdata)
  ARM: edma: No need to clean the pdata in edma_of_parse_dt()
  ARM: edma: Clean up and simplify the code around irq request
  dmaengine: edma: update DMA memcpy to use new param element
  dmaengine: edma: Document variables used for residue accounting
  dmaengine: edma: Provide granular accounting
  dmaengine: edma: Make reading the position of active channels work
  dmaengine: edma: Store transfer data in edma_desc and edma_pset
  dmaengine: edma: Create private pset struct
  ...
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'davinci-fixes-for-v3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers

The patch fixes EDMA crossbar mapping to actually
make it work. The patch has been tagged for stable.

* tag 'davinci-fixes-for-v3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: common: edma: Fix xbar mapping

Merge tag 'omap-for-v3.16/l3-noc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers

Merge "ARM: omap l3-noc bus driver changes for v3.16 merge window, resend" from
Tony Lindgren:

Improvments to omap l3-noc bus driver for v3.16 merge window
to add support for am347x and dra7.

* tag 'omap-for-v3.16/l3-noc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
  bus: omap_l3_noc: Add AM4372 interconnect error data
  bus: omap_l3_noc: Add DRA7 interconnect error data
  bus: omap_l3_noc: introduce concept of submodule
  bus: omap_l3_noc: Add information about the context of operation
  bus: omap_l3_noc: add information about the type of operation
  bus: omap_l3_noc: ignore masked out unclearable targets
  bus: omap_l3_noc: improve readability by using helper for slave event parsing
  bus: omap_l3_noc: make error reporting and handling common
  bus: omap_l3_noc: fix masterid detection
  bus: omap_l3_noc: convert flagmux information into a structure
  bus: omap_l3_noc: use of_match_data to pick up SoC information
  bus: omap_l3_noc: Add support for discountinous flag mux input numbers
  bus: omap_l3_noc: convert target information into a structure
  bus: omap_l3_noc: move L3 master data structure out
  bus: omap_l3_noc: un-obfuscate l3_targ address computation
  bus: omap_l3_noc: switch over to relaxed variants of readl/writel
  bus: omap_l3_noc: populate l3->dev and use it
  bus: omap_l3_noc: remove iclk from omap_l3 struct
  bus: omap_l3_noc: rename functions and data to omap_l3
  bus: omap_l3_noc: Fix copyright information
  ...
Signed-off-by: NOlof Johansson <olof@lixom.net>

The match tables must be zero-terminated, and Kbuild now helpfully
fails to link the kernel if that isn't the case.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This patch documents the sysfs properties exposed by the Broadcom GISB
bus arbiter hardware.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This patch adds the Broadcom GISB arbiter Device Tree binding that is
used on all Broadcom Set-top-box System-on-a-chip.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This patch adds support for the Broadcom GISB arbiter bus timeout/error
handler. GISB is a proprietary bus used by Broadcom Set Top Box
System-on-a-chip devices (BCM7xxx) which allows multiple masters and
clients to be interfaced with each other.

The bus arbiter offers support for generating two interrupts towards the
host CPU, thus allowing us to "catch" clock gated masters, or masters
being volontarily blocked for powersaving purposes, or do general system
troubleshooting.

We also register a hook with the ARM fault exception handling to allow
printing a more informative message than "imprecise external abort at
0x00000000" for instance.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Allwinner drivers changes for 3.16, take 2

Add reset driver for the A31

* tag 'sunxi-drivers-for-3.16-2' of https://github.com/mripard/linux:
  power: reset: Add Allwinner A31 reset code
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'qcom-drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/drivers

Qualcomm ARM Based driver Updates for v3.16

* Introduce drivers/soc directory for misc SoC specific code
* Add driver to configure GSBI device

* tag 'qcom-drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
  soc: qcom: Add GSBI driver
  soc: Introduce drivers/soc place-holder for SOC specific drivers
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The GSBI (General Serial Bus Interface) driver controls the overarching
configuration of the shared serial bus infrastructure on APQ8064, IPQ8064, and
earlier QCOM processors.  The GSBI supports UART, I2C, SPI, and UIM
functionality in various combinations.
Signed-off-by: NAndy Gross <agross@codeaurora.org>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Based on earlier thread "https://lkml.org/lkml/2013/10/7/662" and
discussion at Kernel Summit'2013, it was agreed to create
'driver/soc' for drivers which are quite SOC specific.

Further discussion on the subject is in response to
the earlier version of the patch is here:
	http://lwn.net/Articles/588942/

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NSandeep Nair <sandeep_n@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

That code used to be in the machine code, but it's more fit here with other
restart hooks.

That will allow to cleanup the machine directory, while waiting for a proper
watchdog driver for the A31.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

The following parameters are no longer needed by the edma driver since the
information can be obtained from the IP's CCCFG register:
n_channel, n_region, n_slot and n_tc.
Remove the n_cc as well since in this context it has no meaning. We have
separate edma_soc_info struct/eDMA3_CC instance so this member does not
make any sense (and the driver no longer uses it).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The following parameters are no longer needed by the edma driver since the
information can be obtained from the IP's CCCFG register:
n_channel, n_region, n_slot and n_tc.
Remove the initialization of n_cc as well since in this context it has no
meaning. We have separate edma_soc_info struct/eDMA3_CC instance so this
member does not make any sense (and the driver no longer uses it).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

dma-channels, ti,edma-regions and ti,edma-slots no longer needed in DT since
the the same information is available in the IP's CCCFG register.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

dma-channels, ti,edma-regions and ti,edma-slots no longer needed in DT since
the the same information is available in the IP's CCCFG register.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

From CCCFG register of eDMA3 we can get all the needed information for the
driver about the IP:
Number of channels: NUM_DMACH
Number of regions: NUM_REGN
Number of slots (PaRAM sets): NUM_PAENTRY
Number of TC/EQ: NUM_EVQUE

The ti,edma-regions; ti,edma-slots and dma-channels in DT are
redundant since the very same information can be obtained from the HW.
The mentioned properties are deprecated.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

From CCCFG register of eDMA3 we can get all the needed information for the
driver about the IP:
Number of channels: NUM_DMACH
Number of regions: NUM_REGN
Number of slots (PaRAM sets): NUM_PAENTRY
Number of TC/EQ: NUM_EVQUE

In case when booted with DT or the queue_priority_mapping is not provided
set up a default priority map.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NJoel Fernandes <joelf@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

To be consistent in the code that we take parameters from edma_cc[j] struct
and not randomly from info[j] as well.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The struct edma is allocated per CC bases so the member num_cc does not make
any sense. One CC is one CC, it does not have sub CCs.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

It is no longer in use by the driver or board files.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Merge tag 'samsung-drivers' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/drivers

Merge "Samsung driver update for 3.16" from Kukjin Kim:

exynos_mct update for v3.16

- register sched_clock callback to use clocksource mct-frc

* tag 'samsung-drivers' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  clocksource: exynos_mct: register sched_clock callback
Signed-off-by: NOlof Johansson <olof@lixom.net>

It is ignored by the edma driver since we are just setting back the default
mapping of TC -> Queue.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

There is no need to change the default TC -> Queue mapping. By default the
mapping is: TC0 -> Q0, TC1 -> Q1, etc.
Changing this has no benefits at all and all the board files are just setting
the same mapping back to the HW.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Instead of saving the for loop length, take the num_tc value from the pdata.
In case of DT boot set the n_tc to 3 as it is hardwired in edma_of_parse_dt()
This is a temporary state since upcoming patch(es) will change how we are
dealing with these parameters.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The pdata has been just allocated with devm_kzalloc() in
edma_setup_info_from_dt() and passed to this function.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Get the two interrupt line number at the same time by merging the two
instance of if(node){}else{} places.
replace the &pdev->dev with the already existing dev which makes it possible
to collapse lines with devm_request_irq()
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Merge "Allwinner drivers changes for 3.16" from Maxime Ripard:

Reset drivers for the A31, that have been merged with reset maintainer's
Acked-by.

* 'sunxi/drivers-for-3.16' of https://github.com/mripard/linux:
  reset: sunxi: allow MFD subdevices probe
  reset: sunxi: document sunxi's reset controllers bindings
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge "ARM: mvebu: driver changes for v3.16" from Jason Cooper:

mvebu driver changes for v3.16

 - mvebu-devbus
    - changes need to add support for the orion5x platform

* tag 'mvebu-drivers-3.16' of git://git.infradead.org/linux-mvebu:
  memory: mvebu-devbus: add a devbus, keep-config property
  memory: mvebu-devbus: add Orion5x support
  memory: mvebu-devbus: split functions
  memory: mvebu-devbus: use _SHIFT suffixes instead of _BIT
  memory: mvebu-devbus: use ARMADA_ prefix in defines
  ARM: orion5x: fix target ID for crypto SRAM window
  memory: mvebu-devbus: fix the conversion of the bus width
Signed-off-by: NOlof Johansson <olof@lixom.net>

The current implementation uses sunxi_reset_init function for both early
init and platform device probe.

The sunxi_reset_init function uses DT to retrieve device resources, which
will be an issue if reset controllers are registered from an MFD device
that define resources from mfd_cell definition.

Moreover, we can make of devm functions when we're in the probe context.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>

Add DT bindings documentation for sunxi's reset controllers.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>

Merge tag 'socfpga-driver-update-for-3.16' of git://git.rocketboards.org/linux-socfpga-next into next/drivers

Merge "drivers: Add reset driver for SOCFPGA" from Dinh Nguyen:

Add a reset driver for the SOCFPGA platform.

* tag 'socfpga-driver-update-for-3.16' of git://git.rocketboards.org/linux-socfpga-next:
  reset: add driver for socfpga
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add AM4372 information to handle L3 error.

AM4372 has two clk domains 100f and 200s. Provide flagmux and data
associated with it.

NOTE: Timeout doesn't have STDERRLOG_MAIN register. And per hardware
team, L3 timeout error cannot be cleared the normal way (by setting
bit 31 in STDERRLOG_MAIN), instead it may be required to do system
reset. L3 error handler can't help in such scenarios.

Hence indicate timeout target offset as L3_TARGET_NOT_SUPPORTED as
done for undocumented bits.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NDarren Etheridge <detheridge@ti.com>
Tested-by: NSekhar Nori <nsekhar@ti.com>

DRA7 is distinctly different from OMAP4 in terms of masters and clock
domain organization. There two main clock domains which is divided as
follows:
     <0x44000000 0x1000000> is clk1 and clk2 is the sub clock domain
     <0x45000000 0x1000> is clk3

Add all the data needed to handle L3 error handling on DRA7 devices
and mark clk2 as subdomain and provide a compatible flag for
functionality. Other than the data difference the hardware blocks
involved are essentially the same.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
[nm@ti.com: bugfixes and generic improvements, documentation]
Signed-off-by: NNishanth Menon <nm@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NDarren Etheridge <detheridge@ti.com>
Tested-by: NSekhar Nori <nsekhar@ti.com>

While OMAP4 and OMAP5 had 3 separate clock domains, DRA7 has only 2
and the first one then is internally divided into 2 sub clock domains.

To better represent this in the driver, we use the concept of submodule.

The address defintions in the devicetree is as per the high level
clock domain(module) base, the sub clockdomain/subdomain which shares
the same register space of a clockdomain is marked in the SoC data as
L3_BASE_IS_SUBMODULE.

L3_BASE_IS_SUBMODULE is used as an indication that it's base address is
the same as the parent module and offsets are considered from the same
base address as they are usually intermingled.

Other than the base address, the submodule is same as a module as it is
functionally so.
Signed-off-by: NNishanth Menon <nm@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NDarren Etheridge <detheridge@ti.com>
Tested-by: NSekhar Nori <nsekhar@ti.com>

L3 error may be triggered using Debug interface (example JTAG) or
due to other errors, for example an opcode fetch (due to function
pointer or stack corruption) or a data access (due to some other
failure). NOC registers contain additional information to help aid
debug information.

With this, we can enhance the error information to more detailed form:
"
L3 Custom Error: MASTER MPU TARGET L4PER2 (Read): Data Access in User mode
during Functional access
"
Signed-off-by: NNishanth Menon <nm@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NDarren Etheridge <detheridge@ti.com>
Tested-by: NSekhar Nori <nsekhar@ti.com>