I was hoping ATA_HORKAGE_NODMA | ATA_HORKAGE_SKIP_PM could keep it
happy but no even this doesn't work under certain configurations and
it's not like we can do anything useful with the cofig device anyway.
Replace ATA_HORKAGE_SKIP_PM with ATA_HORKAGE_DISABLE and use it for
the config device.  This makes the device completely ignored by
libata.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

When 4140 PMP is attached to sil24, NCQ commands to fan out port 1 and
2 (0 based) often stall if commands are in progress to other ports.
I've tried a number of things but can't tell what's going on.  It
never happens w/ ahci and reportedly sata_mv which can issue NCQ
commands to multiple devices simultaneously like sil24 does.

Disable NCQ for devices behind 4140 PMP for the time being.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

There's no reason to schedule LPM action after probing is complete
causing another EH iteration.  Just schedule it together with probing
itself.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

PMP notification during reset can make some controllers fail reset
processing and needs to be turned off during resets.  PMP attach and
full-revalidation path did this via sata_pmp_configure() but the quick
revalidation wasn't.  Move the notification disable code right above
fan-out port recovery so that it's always turned off.

This fixes obscure reset failures.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This timeout was set low because previously PMP register access was
done via polling and register access timeouts could stack up.  This is
no longer the case.  One timeout will make all following accesses fail
immediately.

In rare cases both marvell and SIMG PMPs need almost a second.  Bump
it to 3s.

While at it, rename it to SATA_PMP_RW_TIMEOUT.  It's not specific to
SCR access.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

No reason to get overzealous about recovered comm and data errors.
Some PHYs habitually sets them w/o no good reason and being draconian
about these soft error conditions doesn't seem to help anybody.

If need ever rises, we might need to add soft PHY error condition, say
AC_ERR_MAYBE_ATA_BUS and use it only to determine whether speed down
is necessary but I don't think that's very likely to happen.  It's far
more likely we'll get timeouts or fatal transmission errors if
recovered errors are so prominent that they hamper operation.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Originally, whole reset processing was done while the port is frozen
and SError was cleared during @postreset().  This had two race
conditions.  1: hotplug could occur after reset but before SError is
cleared and libata won't know about it.  2: hotplug could occur after
all the reset is complete but before the port is thawed.  As all
events are cleared on thaw, the hotplug event would be lost.

Commit ac371987 kills the first race
by clearing SError during link resume but before link onlineness test.
However, this doesn't fix race #2 and in some cases clearing SError
after SRST is a good idea.

This patch solves this problem by cross checking link onlineness with
classification result after SError is cleared and port is thawed.
Reset is retried if link is online but all devices attached to the
link are unknown.  As all devices will be revalidated, this one-way
check is enough to ensure that all devices are detected and
revalidated reliably.

This, luckily, also fixes the cases where host controller returns
bogus status while harddrive is spinning up after hotplug making
classification run before the device sends the first FIS and thus
causes misdetection.

Low level drivers can bypass the logic by setting class explicitly to
ATA_DEV_NONE if ever necessary (currently none requires this).
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Previously reset freeze/thaw handling lived outside of ata_eh_reset()
mainly because the original PMP reset code needed the port frozen
while resetting all the fan-out ports, which is no longer the case.

This patch moves freeze/thaw handling into ata_eh_reset().
@prereset() and @postreset() are now called w/o freezing the port
although @prereset() an be called frozen if the port is frozen prior
to entering ata_eh_reset().

This makes code simpler and will help removing hotplug event related
races.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Reorganize ata_eh_reset() such that @prereset() is called even when no
reset method is available and if block is used instead of goto to skip
actual reset.  This makes no reset case behave better (readiness wait)
and future changes easier.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The @online out parameter is supposed to set to true iff link is
online and reset succeeded as advertised in the function description
and callers are coded expecting that.  However, sata_link_reset()
didn't behave this way on device readiness test failure.  Fix it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Minor coding-style fixes for sata_promise:
- remove stray blank lines
- fix checkpatch.pl errors; warnings about long lines
  remain, but I don't intend to address those at this time
- remove two inline directives: neither is essential and
  both functions are trivially inlinable anyway by virtue
  of being static and having a single unique call site
- fix comment in pdc_interrupt(): the bits in PDC_INT_SEQMASK
  denote SEQIDs not tags, the distinction becomes important
  when NCQ gets implemented
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch cleans up sata_promise's mmio accesses.

In sata_promise there are three distinct mmio address spaces:
1. global registers, offsets from host->iomap[PDC_MMIO_BAR]
2. per-port ATA registers, offsets from ap->ioaddr.cmd_addr
3. per-port SATA registers, offsets from ap->ioaddr.scr_addr

The driver currently often fails to indicate which address space
a given mmio base pointer refers to, which is a source of bugs
and confusion (see recent pdc_thaw() irq clearing bug; it's also
been an obstacle for the pending NCQ extensions).

To reduce these problems, adopt a coding style where the name of
a base pointer always indicates which address space it refers to:
1. global registers: host_mmio
2. per-port ATA registers: ata_mmio
3. per-port SATA registers: sata_mmio

Also rearrange register offset definitions to clearly indicate
which address space they belong to, and add a symbolic definition
for the previously hard-coded PHYMODE4 register.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch fixes two bugs in sata_promise's irq status clearing paths:
1. When clearing the irq status for a specific port, the driver
   read the global SEQMASK register. This is wrong because that
   clears the irq status for _all_ ports.
2. pdc_thaw() incorrectly added the PDC_INT_SEQMASK host register
   offset to a per-port ata engine base address. This resulted in
   it reading the unrelated PDC_PKT_SUBMIT register, which did not
   have the desired irq status clearing effect.

In both cases the fix is to read from the port's Command/Status
register. This also matches what Promise's own driver does.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use the kernel-provided clamp_val() macro.

FIT was always applied to a member of struct ata_timing (unsigned short)
and two constants.  clamp_val will not cast to short anymore.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Check for an empty request queue before stopping EDMA after a FBS-NCQ error,
as per recommendation from the Marvell datasheet.

This ensures that the EDMA won't suddenly become active again
just after our subsequent check of the empty/idle bits.

Also bump DRV_VERSION.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Part five of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.

Keep a cached copy of the main_irq_mask so that we don't have
to stall the CPU to read it on every pass through mv_interrupt.

This significantly speeds up interrupt handling, both for sata_mv,
and for any other driver/device sharing the same PCI IRQ line.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Part four of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.

Ignore masked IRQs in mv_interrupt().
This prevents "unexpected device interrupt while idle" messages.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Part three of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.

Partially fix a reported bug whereby we sometimes miss seeing drives on
a port-multiplier, as reported by Gwendal Grignou <gwendal@google.com>.

The problem was that we were receiving unexpected interrupts
during EH from POLLed commands while accessing port-multiplier registers.
These unexpected interrupts can be prevented by masking the DONE_IRQ bit
for the port whenever not operating in EDMA mode.

Also fix port_stop() to mask all port interrupts.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Part two of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.

Consolidate all updates of the host main_irq_mask register
into a single function.  This simplifies maintenance,
and also prepares the way for caching it (later).

No functionality changes in this update.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Part one of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.

Don't blindly enable port IRQs at host init time.
Instead, enable only the bits that we want,
which in this case is simply the PCI_ERR bit.

The per-port bits can wait until the ports are reset/probed for devices.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Now that we handle the FIS_IRQ_CAUSE register correctly,
we can also now handle SATA asynchronous notification events.

So enable them, but only for the more modern GenIIe chips.
(older chips have unaddressed errata issues related to this).

This fixes hot plug/unplug for port-muliplier ports.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Group all of the flags for GenIIe devices into a common definition,
to ensure that any updates to them are shared by all GenIIe devices.

This will help make future maintenance somewhat simpler.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix handling of the FIS_IRQ_CAUSE register in sata_mv.

This register exists *only* on GenIIe devices, so don't bother
writing to it on older chips.  Also, it has to be read/cleared
in mv_err_intr() before clearing the main ERR_IRQ_CAUSE register.

This keeps sata_mv from getting stuck forever on certain error types.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Always request a softreset after hardreset succeeds.

This fixes a regression reported by Martin Michlmayr <tbm@cyrius.com>.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Remove an explicit memset(.., 0, ...) to a variable allocated with
kzalloc (i.e. 'info').
Signed-off-by: NChristophe Jaillet <christophe.jaillet@wanadoo.fr>
Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Set ATAPI host state machine to control IDE device terminate sequence.
Some IDE harddisk may assert terminate sequence in the middle of a
formal DMA transaction and resume later. Bit DETECT_TERM in ATAPI_CTRL
register determines whether the ATAPI host state machine or the kernel
driver should take care of this case.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/i915: save and restore dsparb and d_state registers.
  drm/i915: fix off by one in VGA save/restore of AR & CR regs.
  drm: disable tasklets not IRQs when taking the drm lock spinlock
  Revert "drm/vbl rework: rework how the drm deals with vblank."

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
  Don't clean bounds.h and asm-offsets.h
  kconfig: incorrect 'len' field initialisation ?
  kernel-doc: allow unnamed bit-fields
  kbuild: filter away debug symbols from kernel symbols
  Remove *.rej pattern from .gitignore
  MAINTAINERS: document names of new kbuild trees
  kbuild: disable modpost warnings for linkonce sections
  kbuild: escape meta characters in regular expression in make TAGS

Since 97965478 ("mm: Get rid of __ZONE_COUNT")
mmzone.h includes bounds.h.
Calling make clean after make prepare removes bounds.h
again so when building external modules this fails.
Signed-off-by: NJan Blunck <jblunck@suse.de>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
--

1) The field 'len' of the 'gstr' structure seems to track the size of the memory
already allocated for the "growable string". So the value of this field should be
the same as the 'malloc()' just above, shouldn't it ?
Signed-off-by: NChristophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Allow for unnamed bit-fields and skip them instead of printing an
erroneous warning message for them, such as:

Warning(include/asm-s390/cio.h:103): No description found for parameter 'u32'

which contains:

struct tm_scsw {
	u32 :1;
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Andi Kleen <andi@firstfloor.org>
reported that he saw a lot of symbols like this:

0000000000000b24 N DW.aio.h.903a6d92.2
0000000000000bce N DW.task_io_accounting.h.8d8de327.0
0000000000000bec N DW.hrtimer.h.c23659c6.0

in his System.map / kallsyms output.

Simple solution is to skip all debugging
symbols (they are marked 'N').
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Paulo Marques <pmarques@grupopie.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  snd-pcsp: silent misleading warning
  snd-pcsp: depend on CONFIG_EXPERIMENTAL
  snd-pcsp: put back the compatibility code for the older alsa-libs
  snd-pcsp: adjust help texts to frighten users

It appears that alsa allows a sound buffer with size not
evenly devided by the period size. This triggers a warning in
snd-pcsp and floods the log. As a quick fix, the warning should
be disabled.
Signed-off-by: NStas Sergeev <stsp@aknet.ru>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Considering all the feedbacks I got, depending snd-pcsp on
CONFIG_EXPERIMENTAL looks like the only safe way to get out
of all the troubles at one go. :)
Signed-off-by: NStas Sergeev <stsp@aknet.ru>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The attached patch adds back the compatibility code, allowing the
driver to work with older alsa-libs.
The removal was premature, it breaks the real-life configs.
Signed-off-by: NStas Sergeev <stsp@aknet.ru>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the warning text to the help of snd-pcsp about the possible problem
with this driver so that user can know of the problem in advance.

Also, removed the obsoleted text about ancient pc-speaker patch in
CONFIG_SOUND help.
Signed-off-by: NStas Sergeev <stsp@aknet.ru>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

* 'hotfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  SUNRPC: AUTH_SYS "machine creds" shouldn't use negative valued uid/gid
  nfs: make nfs4_drop_state_owner() static
  nfs: path_{get,put}() cleanups
  nfs: replace remaining __FUNCTION__ occurrences
  nfs/lsm: make NFSv4 set LSM mount options
  NFSv4: Check the return value of decode_compound_hdr_arg()
  nfs: fix race in nfs_dirty_request
  NFS: Ensure that 'noac' and/or 'actimeo=0' turn off attribute caching

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c/max6875: Really prevent 24RF08 corruption
  i2c-amd756: Fix functionality flags
  i2c: Kill the old driver matching scheme
  i2c: Convert remaining new-style drivers to use module aliasing
  i2c: Switch pasemi to the new device/driver matching scheme
  i2c: Clean up Blackfin BF527 I2C device declarations
  i2c-nforce2: Disable the second SMBus channel on the DFI Lanparty NF4 Expert
  i2c: New co-maintainer