- 11 8月, 2010 2 次提交
-
-
由 Alek Du 提交于
With this patch, the LPM capable EHCI host controller can put device into L1 sleep state which is a mode that can enter/exit quickly, and reduce power consumption. Signed-off-by: NJacob Pan <jacob.jun.pan@intel.com> Signed-off-by: NAlek Du <alek.du@intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alek Du 提交于
EHCI 1.1 addendum introduced several energy efficiency extensions for EHCI USB host controllers: 1. LPM (link power management) 2. Per-port change 3. Shorter periodic frame list 4. Hardware prefetching This patch is intended to define the HW bits and debug interface for EHCI 1.1 addendum. The LPM and Per-port change patches will be sent out after this patch. Signed-off-by: NJacob Pan <jacob.jun.pan@intel.com> Signed-off-by: NAlek Du <alek.du@intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 21 5月, 2010 2 次提交
-
-
由 Alan Stern 提交于
This patch (as1380) fixes a bug in the wakeup settings for EHCI host controllers. When the controller is suspended, if it isn't enabled for remote wakeup then we have to turn off all the port wakeup flags. Disabling PCI PME# isn't good enough, because some systems (Intel) evidently use alternate wakeup signalling paths. In addition, the patch improves the handling of the Intel Moorestown hardware by performing various power-up and power-down delays just once instead of once for each port (i.e., the delays are moved outside of the port loops). This requires extra code, but the total delay time is reduced. There are also a few additional minor cleanups. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Reported-by: NOndrej Zary <linux@rainbow-software.org> CC: Alek Du <alek.du@intel.com> CC: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1348) removes the bogus USB_PORT_FEAT_{HIGHSPEED,SUPERSPEED} symbols from ch11.h. No such features are defined by the USB spec. (There is a PORT_LOWSPEED feature, but the spec doesn't mention it except to say that host software should never use it.) The speed indicators are port statuses, not port features. As a temporary workaround for the xhci-hcd driver, a fictional USB_PORT_STAT_SUPER_SPEED symbol is added. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> CC: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 23 4月, 2010 1 次提交
-
-
由 Alan Stern 提交于
This patch (as1369) fixes a problem in ehci-hcd. Some controllers occasionally run into trouble when the driver reclaims siTDs too quickly. This can happen while streaming audio; it causes the controller to crash. The patch changes siTD reclamation to work the same way as iTD reclamation: Completed siTDs are stored on a list and not reused until at least one frame has passed. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Tested-by: NNate Case <ncase@xes-inc.com> CC: <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 19 3月, 2010 1 次提交
-
-
由 Clemens Ladisch 提交于
The EHCI driver stores in usb_host_endpoint.hcpriv a pointer to either an ehci_qh or an ehci_iso_stream structure, and uses the contents of the hw_info1 field to distinguish the two cases. After ehci_qh was split into hw and sw parts, ehci_iso_stream must also be adjusted so that it again looks like an ehci_qh structure. This fixes a NULL pointer access in ehci_endpoint_disable() when it tries to access qh->hw->hw_info1. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Reported-by: NColin Fletcher <colin.m.fletcher@googlemail.com> Cc: stable <stable@kernel.org> Acked-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 01 12月, 2009 1 次提交
-
-
由 Oliver Neukum 提交于
a quirky chipset needs periodic schedules to run for a minimum time before they can be disabled again. This enforces the requirement with a time stamp and a calculated delay Signed-off-by: NOliver Neukum <oliver@neukum.org> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 23 9月, 2009 4 次提交
-
-
由 Alan Stern 提交于
This patch (as1280) fixes an obscure bug in ehci-hcd's dequeuing logic for async URBs. If a later URB is unlinked and the completion routine unlinks an earlier URB, then the earlier URB won't be given back in a timely manner because the endpoint queue isn't rescanned as it should be. Similar bugs occur if an endpoint is reset or a halt is cleared while a completion routine is running, because the subroutines don't test for the COMPLETING state. All these problems are solved by adding a new needs_rescan flag to the ehci_qh structure. If the flag is set while scanning through an idle QH, the scan will be repeated. If the QH isn't idle then an unlink cycle will be initiated, and the proper action will be taken when it becomes idle. Also, an unnecessary test is removed from qh_link_async(): That routine is never called if the QH's state isn't IDLE. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> CC: David Brownell <david-b@pacbell.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alek Du 提交于
The Intel Moorestown EHCI controller supports non-standard HOSTPCx register extension. This register controls the LPM behaviour and controls the behaviour of each USB port. Signed-off-by: NJacob Pan <jacob.jun.pan@intel.com> Signed-off-by: NAlek Du <alek.du@intel.com> Acked-by: NAlan Stern <stern@rowland.harvard.edu> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alek Du 提交于
The ehci_qh structure merged hw and sw together which is not good: 1. More and more items are being added into ehci_qh, the ehci_qh software part are unnecessary to be allocated in DMA qh_pool. 2. If HCD has local SRAM, the sw part will consume it too, and it won't bring any benefit. 3. For non-cache-coherence system, the entire ehci_qh is uncachable, actually we only need the hw part to be uncacheable. Spliting them will let the sw part to be cacheable. Signed-off-by: NAlek Du <alek.du@intel.com> Cc: David Brownell <dbrownell@users.sourceforge.net> CC: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alek Du 提交于
Basically the io watchdog is only useful for those quirk HCDs. For most good ones, it only brings unnecessary wakeups. At least, I know the Intel EHCI HCDs should turn off the flag. Signed-off-by: NAlek Du <alek.du@intel.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 21 9月, 2009 1 次提交
-
-
由 Anand Gadiyar 提交于
trivial: fix typo "for for" in multiple files Signed-off-by: NAnand Gadiyar <gadiyar@ti.com> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
- 13 7月, 2009 1 次提交
-
-
由 Alan Stern 提交于
This patch (as1256) changes ehci-hcd and all the other drivers in the EHCI family to make use of the new clear_tt_buffer callbacks. When a Clear-TT-Buffer request is in progress for a QH, the QH is not allowed to be linked into the async schedule until the request is finished. At that time, if there are any URBs queued for the QH, it is linked into the async schedule. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 16 6月, 2009 1 次提交
-
-
由 Alan Stern 提交于
This patch (as1243) tries to improve ehci-hcd's scheduling of interrupt transfers. Instead of trying to cram all transfers with the same period into the same frame, the new code will spread the transfers out among lots of different frames. This should reduce the periodic schedule load in any one frame -- some host controllers have trouble when there's too much work to do. A more thorough approach would stagger the uframe values as well. But this is enough to make a big improvement. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Tested-by: NDwayne Fontenot <dwayne.fontenot@att.net> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 25 3月, 2009 3 次提交
-
-
由 Harvey Harrison 提交于
The base versions handle constant folding now. Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1204) adds a software retry mechanism to ehci-hcd. It gets invoked when the driver encounters transaction errors on an asynchronous endpoint. On many systems, hardware deficiencies cause such errors to occur if one device is unplugged while the host is communicating with another device. With the patch, the failed transactions are retried and generally succeed the second or third time through. This is based on code originally written by Koichiro Saito. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Tested by: Koichiro Saito <Saito.Koichiro@adniss.jp> CC: David Brownell <david-b@pacbell.net> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1205) moves timer_action() from ehci.h to ehci-hcd.c and makes it out-of-line. Over the years it has grown too big to be inline any more. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 28 2月, 2009 1 次提交
-
-
由 Karsten Wiese 提交于
Currently ITDs are immediately recycled whenever their URB completes. However, EHCI hardware can sometimes remember some ITD state. This means that when the ITD is reused before end-of-frame it may sometimes cause the hardware to reference bogus state. This patch defers reusing such ITDs by moving them into a new ehci member cached_itd_list. ITDs resting in cached_itd_list are moved back into their stream's free_list once scan_periodic() detects that the active frame has elapsed. This makes the snd_usb_us122l driver (in kernel since .28) work right when it's hooked up through EHCI. [ dbrownell@users.sourceforge.net: comment fixups ] Signed-off-by: NKarsten Wiese <fzu@wemgehoertderstaat.de> Tested-by: NPhilippe Carriere <philippe-f.carriere@wanadoo.fr> Tested-by: NFederico Briata <federicobriata@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 08 1月, 2009 1 次提交
-
-
由 Vitaly Bordug 提交于
A published errata for ppc440epx states, that when running Linux with both EHCI and OHCI modules loaded, the EHCI module experiences a fatal error when a high-speed device is connected to the USB2.0, and functions normally if OHCI module is not loaded. There used to be recommendation to use only hi-speed or full-speed devices with specific conditions, when respective module was unloaded. Later, it was observed that ohci suspend is enough to keep things going, and it was turned into workaround, as explained below. Quote from original descriprion: The 440EPx USB 2.0 Host controller is an EHCI compliant controller. In USB 2.0 Host controllers, each EHCI controller has one or more companion controllers, which may be OHCI or UHCI. An USB 2.0 Host controller will contain one or more ports. For each port, only one of the controllers is connected at any one time. In the 440EPx, there is only one OHCI companion controller, and only one USB 2.0 Host port. All ports on an USB 2.0 controller default to the companion controller. If you load only an ohci driver, it will have control of the ports and any deviceplugged in will operate, although high speed devices will be forced to operate at full speed. When an ehci driver is loaded, it explicitly takes control of the ports. If there is a device connected, and / or every time there is a new device connected, the ehci driver determines if the device is high speed or not. If it is high speed, the driver retains control of the port. If it is not, the driver explicitly gives the companion controller control of the port. The is a software workaround that uses Initial version of the software workaround was posted to linux-usb-devel: http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg54019.html and later available from amcc.com: http://www.amcc.com/Embedded/Downloads/download.html?cat=1&family=15&ins=2 The patch below is generally based on the latter, but reworked to powerpc/of_device USB drivers, and uses a few devicetree inquiries to get rid of (some) hardcoded defines. Signed-off-by: NVitaly Bordug <vitb@kernel.crashing.org> Signed-off-by: NStefan Roese <sr@denx.de> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 01 12月, 2008 1 次提交
-
-
由 Greg Kroah-Hartman 提交于
This reverts commit f0d781d5. It was the wrong thing to do, and does not really do what it said it did. Cc: Yi Yang <yi.y.yang@intel.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 18 10月, 2008 3 次提交
-
-
由 Alan Stern 提交于
This patch (as1147) fixes the remote-wakeup support for EHCI controllers using the ARC/TDI "embedded-TT" core. These controllers turn off the RESUME bit by themselves when a port resume is complete; hence we need to keep separate track of which ports are suspended or in the process of resuming. The patch also makes a couple of small improvements in ehci_irq(), replacing reads of the command register with the value already stored in a local variable. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Tested-by: NThomas Reitmayr <treitmayr@devbase.at> CC: David Brownell <david-b@pacbell.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Yi Yang 提交于
ehci_watchdog will wake up CPU very frequently so that CPU stays at C3 very short, average residence time is about 50 ms on Aspire One, but we expect it should be about 1 second or more, so this kind of periodic timer is very bad for power saving. We can't remove this timer because of some bad USB controller chipset, but at least we should reduce its side effect to as possible as low. This patch can make CPU stay at C3 longer, average residence time is about twice as long as original. Please consider to apply it, thanks Signed-off-by: NYi Yang <yi.y.yang@intel.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Kumar Gala 提交于
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore remove the dead code associated with !CONFIG_PPC_MERGE. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 26 7月, 2008 1 次提交
-
-
由 Yinghai Lu 提交于
prepare x86: usb debug port early console move ehci struct def to linux/usrb/ehci_def.h from host/ehci.h Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com> Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andi Kleen <andi@firstfloor.org> Cc: "Arjan van de Ven" <arjan@infradead.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: "Greg KH" <greg@kroah.com> Signed-off-by: NIngo Molnar <mingo@elte.hu>
-
- 22 7月, 2008 1 次提交
-
-
由 David Brownell 提交于
This patch fixes some performance bugs observed with some workloads when unlinking EHCI queue header (QH) descriptors from the async ring (control/bulk schedule). The mechanism intended to defer unlinking an empty QH (so there is no penalty in common cases where it's quickly reused) was not working as intended. Sometimes the unlink was scheduled: - too quickly ... which can be a *strong* negative effect, since that QH becomes unavailable for immediate re-use; - too slowly ... wasting DMA cycles, usually a minor issue except for increased bus contention and power usage; Plus there was an extreme case of "too slowly": a logical error in the IAA watchdog-timer conversion meant that sometimes the unlink never got scheduled. The fix replaces a simple counter with a timestamp derived from the controller's 8 KHz microframe counter, and adjusts the timer usage for some issues associated with HZ being less than 8K. (Based on a patch originally by Alan Stern, and good troubleshooting from Leonid.) Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Leonid <leonidv11@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 04 7月, 2008 1 次提交
-
-
由 David Brownell 提交于
This patch fixes a regression in the EHCI driver's TIMER_IO_WATCHDOG behavior. The patch "USB: EHCI: add separate IAA watchdog timer" changed how that timer is handled, so that short timeouts on the remaining timer (unfortunately, overloaded) would never be used. This takes a more direct approach, reorganizing the code slightly to be explicit about only the I/O watchdog role now being overridable. It also replaces a now-obsolete comment describing older timer behavior. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Leonid <leonidv11@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 30 5月, 2008 2 次提交
-
-
由 Alan Stern 提交于
This patch (as1097) fixes a bug in the remote-wakeup handling in ehci-hcd. The driver currently does not keep track of whether the change-suspend feature is enabled for each port; the feature is automatically reset the first time it is read. But recent changes to the hub driver require that the feature be read at least twice in order to work properly. A bit-vector is added for storing the change-suspend feature values. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1095) cleans up the HCD glue and several of the EHCI bus-glue files. The ehci->is_tdi_rh_tt flag is redundant, since it means the same thing as the hcd->has_tt flag, so it is removed and the other flag used in its place. Some of the bus-glue files didn't get the relinquish_port method added to their hc_driver structures. Although that routine currently doesn't do anything for controllers with an integrated TT, in the future it might. So the patch adds it where it is missing. Lastly, some of the bus-glue files have erroneous entries for their hc_driver's suspend and resume methods. These method pointers are specific to PCI and shouldn't be used otherwise. (The patch also includes an invisible whitespace fix.) Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
-
- 02 2月, 2008 6 次提交
-
-
由 David Brownell 提交于
While most isochronous endpoints have short polling intervals, the EHCI driver won't necessarily handle larger ones correctly. This patch switches to use a "u16" to represent those periods, not a u8, since it can always work: the largest expressible period is 2^15 units ... not the previous too-short limit of 128 frames (full or low speeds) or microframes (high speed, 32 frames). This bug is essentially theoretical, since the few ISO endpoints I've seen which don't use one transfer per frame are high speed ones using more than that (including high bandwidth, 24 KB/msec). Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Karsten Wiese 提交于
In the EHCI driver, itd->usecs[8] is used in periodic_usecs(), indexed by uframe. For an ITD's unused uframes it is 0, else it contains the same value as itd->stream->usecs. To check if an ITD's uframe is used, we can instead test itd->hw_transaction[uframe]: if used, it will be nonzero no matter what endianess is used. This patch replaces those two uses, eliminates itd->usecs[], and saves eight bytes from each ITD. Signed-off-by: NKarsten Wiese <fzu@wemgehoertderstaat.de> Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Vladimir Barinov 提交于
EHCI Glue driver for Intel IXP4XX EHCI USB controller Signed-off-by: NVladimir Barinov <vbarinov@ru.mvista.com> Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Valentine Barshak 提交于
This adds device-tree-aware ehci-ppc-of driver. The code is based on the ehci-ppc-soc driver by Stefan Roese <sr@denx.de>. Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com> Acked-by: NArnd Bergmann <arnd@arndb.de> Acked-by: NStefan Roese <sr@denx.de> Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1028) was mostly written by David Brownell; I made only a few changes (extra log info and a small bug fix -- which might account for why David's version had to be reverted). It adds a new watchdog timer to the ehci-hcd driver to be used exclusively for detecting lost or missing IAA notifications. Previously a shared timer had been used, which may have led to some problems as reported by Christian Hoffmann. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Tony Jones 提交于
We should not have multiple line files in sysfs, this moves the data to debugfs instead, like the UHCI driver. Signed-off-by: NTony Jones <tonyj@suse.de> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 21 8月, 2007 1 次提交
-
-
由 Linus Torvalds 提交于
This reverts commit 196705c9. It was reported to cause a regression by Daniel Exner, and Arjan van de Ven points out that we actually already have infrastructure in place for setting limits on acceptable DMA latency that would be the much more correct fix for the problem with some Broadcom EHCI controllers. Fixed up trivial conflicts due to the changes to support big-endian host controller descriptors in drivers/usb/host/{ehci-sched.c,ehci.h}. Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 13 7月, 2007 5 次提交
-
-
由 Vladimir Barinov 提交于
This patch fixes the endianness select for transfer buffers in EHCI controllers that have Transaction Translator built in the hub. Also I cleaned it up to make rid of magic numbers. Signed-off-by: NVladimir Barinov <vbarinov@ru.mvista.com> Cc: <david-b@pacbell.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as887) changes the way ehci-hcd and ohci-hcd handle a loss of VBUS power during suspend. In order for the USB-persist facility to work correctly, it is necessary for low- and full-speed devices attached to a high-speed port to be handed back to the companion controller during resume processing. This entails three changes: adding code to ehci-hcd to perform the handover, removing code from ohci-hcd to turn off ports during root-hub reinit, and adding code to ohci-hcd to turn on ports during PCI controller resume. (Other bus glue resume methods for platforms supporting high-speed controllers would need a similar change, if any existed.) Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 David Brownell 提交于
Remove atomic operations on the reference counter for EHCI queue heads. On various platforms (including ppc7448), atomic operations are unusable with dma-coherent memory. Signed-off-by: NSteven J. Hill <sjhill1@rockwellcollins.com> Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Stefan Roese 提交于
This patch implements supports for EHCI controllers whose in-memory data structures are represented in big-endian format. This is needed (unfortunately) for the AMCC PPC440EPx SoC EHCI controller; the EHCI spec doesn't specify little-endian format, although that's what most other implementations use. The guts of the patch are to introduce the hc32 type and change all references from le32 to hc32. All access routines are converted from cpu_to_le32(...) to cpu_to_hc32(ehci, ...) and similar for the other "direction". (This is the same approach used with OHCI.) David fixed: Whitespace fixes; refresh against ehci cpufreq patch; move glue for that PPC driver to the patch adding it; fix free symbol capture bugs in modified "constant" macros; and make "hc32" etc be "le32" unless we really need the BE options, so "sparse" can do some real good. Signed-off-by: NStefan Roese <sr@denx.de> Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Stuart_Hayes@Dell.com 提交于
EHCI controllers that don't cache enough microframes can get MMF errors when CPU frequency changes occur between the start and completion of split interrupt transactions, due to delays in reading main memory (caused by CPU cache snoop delays). This patch adds a cpufreq notifier to the EHCI driver that will inactivate split interrupt transactions during frequency transitions. It was tested on Intel ICH7 and Serverworks/Broadcom HT1000 EHCI controllers. Signed-off-by: NStuart Hayes <stuart_hayes@dell.com> Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-