Noticed and rough patch by Joe Perches.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

* store UDMA masks in via_isa_bridges[] and while at it make "flags"
  field to be u8 instead of u16

* convert the driver to use UDMA masks from via_isa_bridges[]

* remove no longer needed VIA_UDMA* defines

Make some minor documentation and CodingStyle fixes while at it.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Correct via_do_set_mode() documentation while at it.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Timing registers should be programmed with the desired number of clocks
minus one clock.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

There shouldn't be any problems with it as IDE cs5535 host driver
has been using those values for years and they match values given
in the (publicly available) datasheet.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

s/ARTIM2/ARTTIM23/ in cmd648_bmdma_stop() while at it
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Clear the primary channel pending interrupt bit
instead of the reserved one.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Account for the requirements of the DMA mode currently used
by the pair device.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix incorrect handling of recovery clocks value == 16 resulting
in overclocked recovery timings & potentially underclocked active
timings.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use standard cycle timing for CFA PIO5 and PIO6 modes.

Based on commit 74638c84 for IDE subsystem.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Before only the timings for master were set. Datasheet can be found
here: ftp://ftp.vtbridge.org/Docs/Storage/DS_VT6421A_100_CCPL.PDF
Surprisingly, a slave drive works without this patch. According to the
datasheet, the controller by default derives the DMA mode from the
Set Features command issued to a drive. Not sure about the PIO
timings, though. The real problem is that the timings for the master
effectively are the ones tuned for the slave. If these support
different UDMA-settings, there is trouble, especially when the slave
supports a higher UDMA than the master.

Anyhow, using the same mechanism for both master and slave seems like
a good idea.
Signed-off-by: NBart Hartgers <bart.hartgers@gmail.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Make some variables in ahci and a function in pata_pcmcia static, as found
using sparse.
Signed-off-by: NRobert Hancock <hancockrwd@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Traditional IDE interface sucks in that it doesn't have a reliable IRQ
pending bit, so if the controller raises IRQ while the driver is
expecting it not to, the IRQ won't be cleared and eventually the IRQ
line will be killed by interrupt subsystem.  Some controllers have
non-standard mechanism to indicate IRQ pending so that this condition
can be detected and worked around.

This patch adds an optional operation ->sff_irq_check() which will be
called for each port from the ata_sff_interrupt() if an unexpected
interrupt is received.  If the operation returns %true,
->sff_check_status() and ->sff_irq_clear() will be cleared for the
port.  Note that this doesn't mark the interrupt as handled so it
won't prevent IRQ subsystem from killing the IRQ if this mechanism
fails to clear the spurious IRQ.

This patch also implements ->sff_irq_check() for ata_piix.  Note that
this adds slight overhead to shared IRQ operation as IRQs which are
destined for other controllers will trigger extra register accesses to
check whether IDE interrupt is pending but this solves rare screaming
IRQ cases and for some curious reason also helps weird BIOS related
glitch on Samsung n130 as reported in bko#14314.

  http://bugzilla.kernel.org/show_bug.cgi?id=14314

* piix_base_ops dropped as suggested by Sergei.

* Spurious IRQ detection doesn't kick in anymore if polling qc is in
  progress.  This provides less protection but some controllers have
  possible data corruption issues if the wrong register is accessed
  while a command is in progress.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NJohannes Stezenbach <js@sig21.net>
Reported-by: NHans Werner <hwerner4@gmx.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

host->ports[i] is never NULL if i < host->n_ports and non-NULL return
from ata_qc_from_tag() guarantees that the returned qc is active.
Drop unnecessary tests.

Superflous () dropped as suggested by Sergei.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Tested on AMD internal reference board.
Signed-off-by: NShane Huang <shane.huang@amd.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

HPT36x chips just don't have DPLL.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Describe UDMA timing bits 18-20 and 21 separately; add a note to bit
31 about it being meaningful for PIO only.  Reformat the whole comment,
while at it...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

There's no need to clear the fast interrupt bit in hpt366_set_mode()
since we're doing it in hpt366_init_chipset() already.

While at it, rename 'addr1' local variable to 'addr' and
exclude 'ap->port_no' from its calculation as HPT36x are
single-channel-per-function chips.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

As these drivers' set_piomode() and set_dmamode() methods are almost
identical, factor out the common hpt{37x|3x2n}_set_mode() function
to be called by both of them, the same as in 'pata_hpt366' driver.

This results in ~5% decrease in the 'pata_hpt37x' driver binary
size and in ~4% decrease in the 'pata_hpt3x2n' driver binary size
(as measured on x86-32).
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The UltraDMA Tss timing must be stretched with ATA clock of 66 MHz, but the
driver only does this when PCI clock is 66 MHz, whereas it always programs
DPLL clock (which is used as the ATA clock) to 66 MHz.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use ATA_DMA_* constants instead of the bare numbers for the BMIDE registers.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio: fix out of range array access

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (100 commits)
  ARM: Eliminate decompressor -Dstatic= PIC hack
  ARM: 5958/1: ARM: U300: fix inverted clk round rate
  ARM: 5956/1: misplaced parentheses
  ARM: 5955/1: ep93xx: move timer defines into core.c and document
  ARM: 5954/1: ep93xx: move gpio interrupt support to gpio.c
  ARM: 5953/1: ep93xx: fix broken build of clock.c
  ARM: 5952/1: ARM: MM: Add ARM_L1_CACHE_SHIFT_6 for handle inside each ARCH Kconfig
  ARM: 5949/1: NUC900 add gpio virtual memory map
  ARM: 5948/1: Enable timer0 to time4 clock support for nuc910
  ARM: 5940/2: ARM: MMCI: remove custom DBG macro and printk
  ARM: make_coherent(): fix problems with highpte, part 2
  MM: Pass a PTE pointer to update_mmu_cache() rather than the PTE itself
  ARM: 5945/1: ep93xx: include correct irq.h in core.c
  ARM: 5933/1: amba-pl011: support hardware flow control
  ARM: 5930/1: Add PKMAP area description to memory.txt.
  ARM: 5929/1: Add checks to detect overlap of memory regions.
  ARM: 5928/1: Change type of VMALLOC_END to unsigned long.
  ARM: 5927/1: Make delimiters of DMA area globally visibly.
  ARM: 5926/1: Add "Virtual kernel memory..." printout.
  ARM: 5920/1: OMAP4: Enable L2 Cache
  ...

Fix up trivial conflict in arch/arm/mach-mx25/clock.c

* 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block: (38 commits)
  block: don't access jiffies when initialising io_context
  cfq: remove 8 bytes of padding from cfq_rb_root on 64 bit builds
  block: fix for "Consolidate phys_segment and hw_segment limits"
  cfq-iosched: quantum check tweak
  blktrace: perform cleanup after setup error
  blkdev: fix merge_bvec_fn return value checks
  cfq-iosched: requests "in flight" vs "in driver" clarification
  cciss: Fix problem with scatter gather elements in the scsi half of the driver
  cciss: eliminate unnecessary pointer use in cciss scsi code
  cciss: do not use void pointer for scsi hba data
  cciss: factor out scatter gather chain block mapping code
  cciss: fix scatter gather chain block dma direction kludge
  cciss: simplify scatter gather code
  cciss: factor out scatter gather chain block allocation and freeing
  cciss: detect bad alignment of scsi commands at build time
  cciss: clarify command list padding calculation
  cfq-iosched: rethink seeky detection for SSDs
  cfq-iosched: rework seeky detection
  block: remove padding from io_context on 64bit builds
  block: Consolidate phys_segment and hw_segment limits
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (252 commits)
  ASoC: Check progress when reporting periods from i.MX FIQ handler
  ASoC: Remove a unused variables from i.MX FIQ runtime data
  ALSA: hda - Add/fix ALC269 FSC and Quanta models
  ALSA: hda - Add ALC670 codec support
  OMAP4: PMIC: Add support for twl6030 codec
  ALSA: hda - remove unnecessary msleep on power state transitions
  usb/gadget/{f_audio,gmidi}.c: follow recent changes in audio.h
  ASoC: fsi: Modify over/under run error settlement
  ASoC: OMAP4: Add McPDM platform driver
  ASoC: OMAP4: Add support for McPDM
  ASoC: OMAP: data_type and sync_mode configurable in audio dma
  ALSA: hda - Add missing description in HD-Audio-Models.txt
  ALSA: add support for Macbook Air 2,1 internal speaker
  ALSA: usbaudio: consolidate header files
  ALSA: usbmixer: bail out early when parsing audio class v2 descriptors
  ALSA: usbaudio: implement basic set of class v2.0 parser
  ALSA: usbaudio: introduce new types for audio class v2
  ALSA: usbaudio: parse USB descriptors with structs
  ALSA: hda - enable snoop for Intel Cougar Point
  ALSA: hda - Remove identical definitions for macmini3 model
  ...

Merge branches 'futexes-for-linus', 'irq-core-for-linus' and 'bkl-drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'futexes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  futex: Protect pid lookup in compat code with RCU

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: Fix documentation of default chip disable()

* 'bkl-drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  nvram: Drop the BKL from nvram_open()

* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  posix-timers.c: Don't export local functions
  clocksource: start CMT at clocksource resume
  clocksource: add suspend callback
  clocksource: add argument to resume callback
  ntp: Cleanup xtime references in ntp.c
  ntp: Make time_esterror and time_maxerror static

Add missing kernel-doc notation for new function parameters:

Warning(drivers/scsi/scsi.c:1031): No description found for parameter 'buf'
Warning(drivers/scsi/scsi.c:1031): No description found for parameter 'buf_len'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A ROM resource that doesn't fit should not cause us to try to re-assign
all the bus resources.  Nobody generally cares, and re-assigning is
going to just cause way more troubles than it tries to solve.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As the comment says the initial value of last_waited is never used, so
there is no need to initialise it with the current jiffies. Jiffies is
hot enough without accessing it for no reason.
Signed-off-by: NRichard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>