- 15 6月, 2015 15 次提交
-
-
由 Stanislaw Gruszka 提交于
rt2x00.serialmonkey.com will be shutdown. Since traffic on rt2x00 mailing list is very low, we can use only linux-wireless list for any rt2x00 related topics. Thanks for Luis Correia, Ivo van Doorn and Mark Wallis for maintaining rt2x00 servers for years! Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Chunfan Chen 提交于
If timeshare coexistance between bluetooth and WLAN gets enabled, firmware will give host an event to reduce Rx AMPDU BA window size. The event is handled in this patch. Signed-off-by: NChunfan Chen <jeffc@marvell.com> Signed-off-by: NCathy Luo <cluo@marvell.com> Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Chun-Yeow Yeoh 提交于
Add the support of channel switching functionality, similar to ath9k support. Tested with TP-Link TL-WN722N and TL-WN821N. Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Arend van Spriel 提交于
Some time ago the function debugfs_create_devm_seqfile() was introduced in debugfs. The caller simply needs to provide a device pointer and read function. The function brcmf_debugfs_add_entry() is now simply a wrapper only doing the work for CONFIG_BRCMDBG. Reviewed-by: NHante Meuleman <meuleman@broadcom.com> Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Arend van Spriel 提交于
The watchdog reset as done in brcmf_pcie_buscoreprep() is not sufficient. It needs to modify PCIe core registers as well which is properly done by brcmf_pcie_reset_device() after the chip recognition is done. So the faulty watchdog reset can be removed as it was causing driver reload to fail and hang the system requiring a power-cycle. Instead the call to to the brcmf_pcie_reset_device() function is done twice in the unload. Reviewed-by: NHante Meuleman <meuleman@broadcom.com> Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Arend van Spriel 提交于
The information provided by chipinfo is also provided by the revinfo debugfs entry. Removing it from debugfs. Reviewed-by: NHante Meuleman <meuleman@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Hante Meuleman 提交于
On device to host data using msgbuf the read pointer gets updated once all data is processed. Updating this pointer more frequently allows the firmware to add more data quicker. This will result in slightly higher and more stable throughput on CPU bounded host processors. Reviewed-by: NArend Van Spriel <arend@broadcom.com> Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: NHante Meuleman <meuleman@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Taehee Yoo 提交于
The variable "fw_version" is used in the _ResetDigitalProcedure1(). but It is not initialized. so I add init codes for "fw_version" and "fw_subversion". Signed-off-by: NTaehee Yoo <ap420073@gmail.com> Acked-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Taehee Yoo 提交于
rtl92cu_rx_query_desc set a isampdu twice. but second code is related to isfirst_ampdu. so i change it. Signed-off-by: NTaehee Yoo <ap420073@gmail.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Taehee Yoo 提交于
In the rtlwifi/rtl8192cu, I change debug message "RTL8192CE" to "RTL8192CU". Signed-off-by: NTaehee Yoo <ap420073@gmail.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Taehee Yoo 提交于
in the _rtl92c_phy_rf6052_config_parafile(), cases RF90_PATH_A and RF90_PATH_B call the same routine. so i remove one of these routine. also the return routine is duplicated. so i remove it. Signed-off-by: NTaehee Yoo <ap420073@gmail.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Hans Ulli Kroll 提交于
While working on getting my rtl8821au driver in pretty shape for inclusion, it is dicosvered that the tm_trigger flag is used only for the first device using this driver. This flag handles the thermal power management in the hardware. To change this add a entry in sttruct rtl_dm, so each device can handle is separately. Signed-off-by: NHans Ulli Kroll <ulli.kroll@googlemail.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Taehee Yoo 提交于
in the rtlwifi/rtl8192cu, INTF_PCI and INTF_USB is unnecessary. because RTL8192CU chipset is only USB interface. Signed-off-by: NTaehee Yoo <ap420073@gmail.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Taehee Yoo 提交于
_InitBeaconParameters() and rtl92cu_init_beacon_parameters() is same routine. I remove both functions. then i add _rtl92cu_init_beacon_parameters() in the hw.c. _rtl92cu_init_beacon_parameters() is same routine with _InitBeaconParameters(). Signed-off-by: NTaehee Yoo <ap420073@gmail.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Taehee Yoo 提交于
in the rtlwifi/rtl8192cu, IS_HARDWARE_TYPE_8192CE and IS_HARDWARE_TYPE_8192CU is unnecessary. because rtlwifi/rtl8192cu codes aren't shared. Signed-off-by: NTaehee Yoo <ap420073@gmail.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
- 08 6月, 2015 25 次提交
-
-
由 Rafał Miłecki 提交于
This extension of BCMA_DRIVER_PCI has no reason to depend on BCMA_HOST_PCI. User may just want to have PCI device attached to SoC registered without enabling any extra client mode code. This can be useful when having non-bcma PCI device attached or when using other PCI driver. Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Rafał Miłecki 提交于
It seems Broadcom released two devices with conflicting device id. There are for sure 14e4:4321 PCI devices with BCM4321 (N-PHY) chipset, they can be found in routers, e.g. Netgear WNR834Bv2. However, according to Broadcom public sources 0x4321 is also used for 5 GHz BCM4306 (G-PHY). It's unsure if they meant PCI device id, or "virtual" id (from SPROM). To distinguish these devices lets check PHY type (G vs. N). Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Cc: <stable@vger.kernel.org> # 3.16+ Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Rafał Miłecki 提交于
As we plan to add support for platform NVRAM we should store direct data pointer without the extra struct firmware layer. This will allow us to support other sources with the only requirement being u8 buffer. Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Acked-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Jakub Kicinski 提交于
Most drivers use FIF_OTHER_BSS to set promiscous mode. Let us follow their lead even though it doesn't match exactly the HW filter flags. Signed-off-by: NJakub Kicinski <kubakici@wp.pl> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Jakub Kicinski 提交于
Make sure .disconnect() doesn't cleanup the device if .resume() failed. This may happen when device is removed during suspend. Signed-off-by: NJakub Kicinski <kubakici@wp.pl> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Jakub Kicinski 提交于
Users of older Ralink devices report that received frames sometimes have zero length. Watch out for that. Signed-off-by: NJakub Kicinski <kubakici@wp.pl> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Jakub Kicinski 提交于
Signed-off-by: NJakub Kicinski <kubakici@wp.pl> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Rafał Miłecki 提交于
This allows e.g. user space to use /sys/class/ieee80211/*/macaddress Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Rafał Miłecki 提交于
Recently Broadcom added support for NVRAMs with entries for multiple PCIe devices. One of the supported formats is based on prefixes defined like: devpath0=pcie/1/4/ and entries like 0:foo=bar 0:baz=qux etc. Unfortunately there are also a bit older devices using different way of defining prefixes, e.g. SmartRG SR400ac (2 x BCM43602) with entries: devpath0=pci/1/1/ devpath1=pci/2/1 Broadcom stated this old format will never be used/supported by brcmfmac but given the simplicity of this patch I'll insist on supporting it. Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Avinash Patil 提交于
It was observed that AP beacons would not reflect correct regulatory information upon starting AP in A band. This was because of missing AP config band update in set_channel of start_ap. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Zhaoyang Liu 提交于
This patch fixes semantic warning for debugging data dump feature. Previous code is based on the assumption that skb is not null. New change makes sure that we already have data buffer. Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NZhaoyang Liu <liuzy@marvell.com> Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Taehee Yoo 提交于
After physical reconnect, the rtl8192cu chipset shows low transmission rates.It cause is that variable "iqk_initialized" do not de-initialized. So I add this code. Signed-off-by: NTaehee Yoo <ap420073@gmail.com> Acked-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Xinming Hu 提交于
Negative adapter->tx_pending is observed while running data traffic, because tx_pending is decreased once more for AMSDU packet. since tx_pending have been decreased for all the source MSDU packets, we don't need to update once more for AMSDU packet. Signed-off-by: NXinming Hu <huxm@marvell.com> Signed-off-by: NCathy Luo <cluo@marvell.com> Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Xinming Hu 提交于
This patch fixes issue with the accessing correct ra_list by downgrading corresponding tid number. Alternatively, ra lists are created in mwifiex_wmm_add_buf_txqueue using downgraded tid number. Signed-off-by: NXinming Hu <huxm@marvell.com> Signed-off-by: NCathy Luo <cluo@marvell.com> Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Avinash Patil 提交于
This was missing and would cause issue in WMM handling. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NCathy Luo <cluo@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Avinash Patil 提交于
This would enable driver to enter powersave as soon as connected. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NCathy Luo <cluo@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Avinash Patil 提交于
We often see ADDBA request packets coming to driver because driver has registered for action frame subtype. We dont process BA action frames in host; drop such frames. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NXinmin Hu <huxm@marvell.com> Signed-off-by: NCathy Luo <cluo@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Avinash Patil 提交于
Earlier only RSN, WPA and channel switch IEs from tail buffer would be downloaded to FW. This patch adds support for downloading more IEs from tail buffer. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NCathy Luo <cluo@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Avinash Patil 提交于
This patch adds support to parse power constraint IEs from Tail buffer. This power constraint is then set to FW during bss_config download. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NCathy Luo <cluo@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Xinming Hu 提交于
This patch extend cfg80211 dump_station handler, support for dump stations associated to mwifiex micro AP. Signed-off-by: NXinming Hu <huxm@marvell.com> Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NCathy Luo <cluo@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Xinming Hu 提交于
This patch add sta_list firmware command, which can be used to get power status and rssi for the stations associated to mwifiex micro AP. Signed-off-by: NXinming Hu <huxm@marvell.com> Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NCathy Luo <cluo@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Xinming Hu 提交于
This patch maintain statistic information for the stations associated to the mwifiex micro AP, include tx/rx bytes/packets, signal strength, tx bitrate. Signed-off-by: NXinming Hu <huxm@marvell.com> Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NCathy Luo <cluo@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Xinming Hu 提交于
This patch add cfg80211 get_channel handler for mwifiex. The handler will be used to report current channel to upper layer utility. Signed-off-by: NXinming Hu <huxm@marvell.com> Signed-off-by: NCathy Luo <cluo@marvell.com> Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Avinash Patil 提交于
This patch adds support to disable ongoing CAC in FW upon detecting radar during CAC period. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NCathy Luo <cluo@marvell.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-