While trying to make GSM modem Onda MT503HS working, I found a mismatch
between device id in the driver code (0x0200) and id in the lsusb
output (0x2000).

This patch fixed it for me, but I don't know if the original device id was
also correct and the new ID should be added instead of replacing the
old one.
Signed-off-by: NMarcel Sebek <sebek64@post.cz>
Acked-by: NDomenico Riccio <domenico.riccio@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The ZTE modem entry causes usb-storage to ignore the device, but for some
versions of the device, usb-storage mode is required to get to modem ode. For
both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work.

Note that the various versions of the device have the same ProductId,
VendorId, and bcdDevice number, so we cannot have the entry for some and not
others.
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds another unusual_devs.h entry for a device that can't handle more
than 64k reads/writes in a single command.
Signed-off-by: NJean-Baptiste Onofre <jb@nanthrax.net>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Running a 32-bit usbmon(8) on 2.6.28-rc9 produces the following:
ioctl32(usbmon:28563): Unknown cmd fd(3) cmd(400c9206){t:ffffff92;sz:12} arg(ffd3f458) on /dev/usbmon0

It happens because the compatibility mode was implemented for 2.6.18
and not updated for the fsops.compat_ioctl API.

This patch relocates the pieces from under #ifdef CONFIG_COMPAT into
compat_ioctl with no other changes except one new whitespace.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Reported by Randy Dunlap from a warning on the v2.6.29 merge window.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil.
Signed-off-by: NMhayk Whandson <eu@mhayk.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the vendor and product ID for the Alti-2 Neptune 3
(http://www.alti-2.com) which uses the FTDI chip.
Signed-off-by: NRobie Basak <rb-oss-1@justgohome.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

My girl use modem GSM (EDGE) Commanader 2 on iPlus Polsih provider,

PLEASE add this vendor=0x10C4 and product=0x822B to USB serial driver cp2101.c

From: Tomasz K <eros81@o2.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

My Brother HL-1440 would print one document before CUPS would stop
printing with the error "Printer not connected; will retry in 30
seconds...". I traced this down to the CUPS usb backend getting an EIO
out of usblp on the IOCNR_GET_DEVICE_ID IOCTL. Adding the
USBLP_QUIRK_BIDIR fixes the problem but is it the right solution?

output from strace /usr/lib/cups/backend/usb after printing a document
(Note: SNDCTL_DSP_SYNC == IOCNR_GET_DEVICE_ID):

before patch

open("/dev/usb/lp0", O_RDWR|O_EXCL)     = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fff2478cef0) = -1 EIO (Input/output error)

after patch

open("/dev/usb/lp0", O_RDWR|O_EXCL)     = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fffb8d474c0) = 0

Possibly related bug: https://bugs.launchpad.net/ubuntu/+source/cupsys/+bug/35638Signed-off-by: NBrandon Philips <bphilips@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Labpro device is in both ldusb and vstusb device tables.
Should only be a vstusb device.
Signed-off-by: Nstephen ware <stephen.ware@eqware.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds a device quirk for a MediaTek Inc GPS chipset. The
device implements USB CDC ACM, but is missing the union descriptor, so
the ACM class driver fails to probe the device.

I've tested this patch with an iBlue A+ GPS which uses this chipset
and using kernel 2.6.28-rc9.
Signed-off-by: NAndrew Lunn, <andrew@lunn.ch>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Below is a patch which allows a number of GPS loggers to work
under linux. It is known to support the i-Blue 747 (all models),
i-Blue 757, Qstarz BT-Q1000, i.Trek Z1, Konet BGL-32, and the Holux
M-241.

From: James A. Treacy <treacy@debian.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index

In some usb gadget driver, for example usb audio class device, the high
byte of w_index is the entity id and low byte is the interface number.
If we use the 2 bytes of w_index as the array number, we will get a
wrong pointer or NULL pointer.

This patch fixes this issue.
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NBryan Wu <cooloney@kernel.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Blackfin MUSB Kconfig text didn't properly parenthesise its
dependencies.  This was visible in non-Blackfin configs by the
way the user interfaces lost track of dependencies, when doing
a bunch of test builds.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Initializes the actual_len field to 0 before every DMA transaction.
Signed-off-by: NSwaminathan S <swami.iyer@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These compilation errors are related to incorrect
debugging macro and variable names and generated the
following errors:

  drivers/usb/musb/cppi_dma.c:437:5: warning: "MUSB_DEBUG" is not defined
  drivers/usb/musb/cppi_dma.c: In function 'cppi_next_rx_segment':
  drivers/usb/musb/cppi_dma.c:884: error: 'debug' undeclared (first use in this function)
Signed-off-by: NHugo Villeneuve <hugo@hugovil.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This set of patches introduces calls to the following set of functions:

usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)

In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:

USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC

An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)

@r5@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
-  \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)

@inc@
@@

#include <linux/usb.h>

@depends on !inc && (r1||r5)@
@@

+ #include <linux/usb.h>
  #include <linux/usb/...>
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/usb/musb/tusb6010_omap.c:18:26: error: asm/arch/dma.h:
  No such file or directory
drivers/usb/musb/tusb6010_omap.c:19:26: error: asm/arch/mux.h:
  No such file or directory
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes insert module failure as free_irq() was not
done in previous rmmod.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The DaVinci code had an implementation of the OTG transceiver glue
too; make it use the new-standard one.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Trying once more to get this merged.  The original was submitted
for 2.6.27-rc2 or so, and never got correctly merged.  Neither
were any of the numerous subsequent resends.  Sigh.

  CC      drivers/usb/musb/davinci.o
drivers/usb/musb/davinci.c:35:32: error: mach/arch/hardware.h: No such file or directory
drivers/usb/musb/davinci.c:36:30: error: mach/arch/memory.h: No such file or directory
drivers/usb/musb/davinci.c:37:28: error: mach/arch/gpio.h: No such file or directory
drivers/usb/musb/davinci.c:373: error: redefinition of 'musb_platform_set_mode'
drivers/usb/musb/davinci.c:368: error: previous definition of 'musb_platform_set_mode' was here
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

> > drivers/built-in.o: In function `ohci_omap_init':
 > > hid-quirks.c:(.text+0x6c608): undefined reference to `otg_get_transceiver'
 > > drivers/built-in.o: In function `omap_udc_probe':
 > > hid-quirks.c:(.init.text+0x34c0): undefined reference to `otg_get_transceiver'
 > > hid-quirks.c:(.init.text+0x3d40): undefined reference to `otg_put_transceiver'
Reported-by: NRussell King <linux@arm.linux.org.uk>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1198) fixes a conceptual bug: Somewhere along the line
we managed to confuse USB class devices with USB char devices.  As a
result, the code to send a disconnect signal to userspace would not be
built if both CONFIG_USB_DEVICE_CLASS and CONFIG_USB_DEVICEFS were
disabled.

The usb_fs_classdev_common_remove() routine has been renamed to
usbdev_remove() and it is now called whenever any USB device is
removed, not just when a class device is unregistered.  The notifier
registration and unregistration calls are no longer conditionally
compiled.  And since the common removal code will always be called as
part of the char device interface, there's no need to call it again as
part of the usbfs interface; thus the invocation of
usb_fs_classdev_common_remove() has been taken out of
usbfs_remove_device().
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NAlon Bar-Lev <alon.barlev@gmail.com>
Tested-by: NAlon Bar-Lev <alon.barlev@gmail.com>
Cc: stable <stable@kernel.org>

Commit a0d4922d
(USB: fix up suspend and resume for PCI host controllers) attempted
to fix the suspend-resume of PCI USB controllers, but unfortunately
it did that incorrectly and interrupts are left enabled by the USB
controllers' ->suspend_late() callback as a result.  This leads to
serious problems during suspend which are very difficult to debug.

Fix the issue by removing the ->suspend_late() callback of PCI
USB controllers and moving the code from there to the ->suspend()
callback executed with interrupts enabled.  Additionally, make
the ->resume() callback of PCI USB controllers execute
pci_enable_wake(dev, PCI_D0, false) to disable wake-up from the
full power state (PCI_D0).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Tested-by: NAndrey Borzenkov <arvidjaar@mail.ru>
Tested-by: N"Jeff Chua" <jeff.chua.linux@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: "Zdenek Kabelac" <zdenek.kabelac@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1199) changes the initial wakeup settings for PCI USB
host controllers.  The controllers are marked as capable of waking the
system, but wakeup is not enabled by default.

It turns out that enabling wakeup for USB host controllers has a lot
of bad consequences.  As the simplest example, if a USB mouse or
keyboard is unplugged immediately after the computer is put to sleep,
the unplug will cause the system to wake back up again!  We are better
off marking them as wakeup-capable and leaving wakeup disabled.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NRafael J. Wysocki <rjw@sisk.pl>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds an unusual devs entry for 2116:0320
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1200) finishes some fixes that were left incomplete by
an earlier patch.

Although nobody has addressed this issue in the past, it turns out
that we need to distinguish between two different modes of disabling
and enabling endpoints.  In one mode only the data structures in
usbcore are affected, and in the other mode the host controller and
device hardware states are affected as well.

The earlier patch added an extra argument to the routines in the
enable_endpoint pathways to reflect this difference.  This patch adds
corresponding arguments to the disable_endpoint pathways.  Without
this change, the endpoint toggle state can get out of sync between
the host and the device.  The exact mechanism depends on the details
of the host controller (whether or not it stores its own copy of the
toggle values).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NDan Streetman <ddstreet@ieee.org>
Tested-by: NDan Streetman <ddstreet@ieee.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds the vendor/product ID of the fasttrax GPS evaluation kit from:
	http://www.fastraxgps.com/products/evaluationtools/evaluationkit/

to the cp2101 module since this device is actually equipped with a
CP210x USB to serial bridge.

The vendor/product ID is: 0x10c4/0x826b.
Signed-off-by: NWolfgang Glas <wolfgang.glas@ev-i.at>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Introduced by 8adb711f ("debugfs:
introduce stub for debugfs_create_size_t() when DEBUG_FS=n") and due to
a simple missing "static inline".
Reported-and-tested-by: NJeff Chua <jeff.chua.linux@gmail.com>
Acked-by: NGreg KH <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/home/rmk/linux-2.6-arm: (22 commits)
  [ARM] fix section-based ioremap
  [NET] am79c961a: fix spin_lock usage
  [ARM] omap: usb: thou shalt not provide empty release functions
  [ARM] omap: watchdog: allow OMAP watchdog driver on OMAP34xx platforms
  [ARM] 5369/1: omap mmc: Add new omap hsmmc controller for 2430 and 34xx, v3
  [ARM] clkdev: fix clock matching
  [ARM] 5370/1: at91: fix rm9200 watchdog
  [ARM] 5368/1: arch/arm/mach-davinci/usb.c buildfix
  [ARM] 5365/1: s3cmci: Use new include path of dma.h
  [ARM] fix StrongARM-11x0 page copy implementation
  [ARM] omap: ensure OMAP drivers pass a struct device to clk_get()
  ARM: OMAP: Fix compile for h3 MMC
  ARM: OMAP: Remove unused platform devices, v3
  ARM: OMAP: Fix ASoC by enabling writes to XCCR and RCCR McBSP registers, v3
  ARM: OMAP: Fix OSK ASoC by registering I2C board info for tlvaic23
  ARM: OMAP: remove duplicated #include's
  ARM: OMAP: Fix DMA CCR programming for request line > 63, v3
  ARM: OMAP: Fix gpio.c compile on 15xx with CONFIG_DEBUGFS
  ARM: OMAP: Fix compile for beagle
  ARM: OMAP: Fix gpio by switching to generic gpio calls, v2
  ...

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c: Warn on deprecated binding model use
  eeprom: More consistent symbol names
  eeprom: Move 93cx6 eeprom driver to /drivers/misc/eeprom
  spi: Move at25 (for SPI eeproms) to /drivers/misc/eeprom
  i2c: Move old eeprom driver to /drivers/misc/eeprom
  i2c: Move at24 to drivers/misc/eeprom
  i2c: Quilt tree has moved
  i2c: Delete many unused adapter IDs
  i2c: Delete 10 unused driver IDs

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
  kbuild: fix kbuild.txt typos
  kbuild: print usage with no arguments in scripts/config
  Revert "kbuild: strip generated symbols from *.ko"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (92 commits)
  gianfar: Revive VLAN support
  vlan: Export symbols as non GPL symbols.
  bnx2x: tx_has_work should not wait for FW
  netxen: reduce memory footprint
  netxen: fix vlan tso/checksum offload
  net: Fix linux/if_frad.h's suitability for userspace.
  net: Move config NET_NS to from net/Kconfig to init/Kconfig
  isdn: Fix missing ifdef in isdn_ppp
  networking: document "nc" in addition to "netcat" in netconsole.txt
  e1000e: workaround hw errata
  af_key: initialize xfrm encap_oa
  virtio_net: Fix MAX_PACKET_LEN to support 802.1Q VLANs
  lcs: fix compilation for !CONFIG_IP_MULTICAST
  rtl8187: Add termination packet to prevent stall
  iwlwifi: fix rs_get_rate WARN_ON()
  p54usb: fix packet loss with first generation devices
  sctp: Fix another socket race during accept/peeloff
  sctp: Properly timestamp outgoing data chunks for rtx purposes
  sctp: Correctly start rtx timer on new packet transmissions.
  sctp: Fix crc32c calculations on big-endian arhes.
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix DAX handling via userspace access from kernel.
  sparc64: Annotate sparc64 specific syscalls with SYSCALL_DEFINEx()
  [CVE-2009-0029] sparc: Enable syscall wrappers for 64-bit
  sparc64: Initialize FHC/CLOCK LED platform_device 'id' field correctly.
  sparc64: fix modpost failure
  sparc64: fix readout of cpu/fpu type

commit 77ecaf2d ("gianfar: Fix VLAN
HW feature related frame/buffer size calculation") wrongly removed
priv->vlgrp assignment, and now priv->vlgrp is always NULL.

This patch fixes the issue, plus fixes following sparse warning
introduced by the same commit:
gianfar.c:1406:13: warning: context imbalance in 'gfar_vlan_rx_register' - wrong count at exit

gfar_vlan_rx_register() checks for "if (old_grp == grp)" and tries
to return w/o dropping the lock.

According to net/8021q/vlan.c VLAN core issues rx_register() callback:
1. In register_vlan_dev() only on a newly created group;
2. In unregister_vlan_dev() only if the group becomes empty.

Thus the check in the gianfar driver isn't needed.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In previous kernels, any kernel module could get access to the
'real-device' and the VLAN-ID for a particular VLAN.  In more recent
kernels, the code was restructured such that this is hard to do
without accessing private .h files for any module that cannot use
GPL-only symbols.

Attached is a patch to once again allow non-GPL modules the ability to
access the real-device and VLAN id for VLANs.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current tx_has_work waited until all packets sent by the driver
are marked as completed by the FW. This is too greedy and it causes
the bnx2x_poll to spin in vain. The driver should only check that all
packets FW already completed are freed - only in unload flow the
driver should make sure that transmit queue is empty
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o reduce rx ring size from 8192 to 4096.
o cut down old huge lro buffers.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o set netdev->vlan_features appropriately.
o fix tso descriptor initialization for vlan case.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>