A root bridge may not have directly attached hotpluggable slots under it.
Instead, it may have p2p bridges with slots under it.  In this case, we need
to clean up the p2p bridges and slots properly too.  Patch below applies on
top of the original patch, and fixes this problem.  Without this, acpiphp
leaves behind notify handlers on module unload, and subsequent module load
attempts don't work properly too.  Patch was tested on an ia64 Tiger4 box.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch converts acpiphp to use the generic PCI resource assignment code.
It's quite large, but most of it is deleting the acpiphp_pci and acpiphp_res
files.  It's tested on an hp Integrity rx8620 (which won't work without this
patch).  Testers with other hardware welcomed.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Export an acpi interface to get PCI domain/bus/devfn information from the
corresponding namespace handle.  Used by acpiphp code to transpate the device
handle of the hot-plugged root bridge to the corresponding pci location
information.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Create new interfaces to recursively add an acpi namespace object to the acpi
device list, and recursively start the namespace object.  This is needed for
ACPI based hotplug of a root bridge hierarchy where the add operation must be
performed first and the start operation must be performed separately after the
hot-plugged devices have been properly configured.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Read bridge io/mem/pfmem ranges when fixing up the bus so that bus resources
are tracked.  This is required to properly support pci end device and bridge
hotplug.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When hot-plugging an I/O hierarchy that contains many bridges and leaf
devices, it's possible that there are not enough resources to start all the
device present.  If we fail to assign a resource, clear the corresponding
value in the pci_dev structure, so other code can take corrective action.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a root bridge hierarchy is hot-plugged, resource requirements for the new
devices may be greater than what the root bridge is decoding.  In this case,
we want to remove devices that did not get needed resources.  These devices
have been scanned into bus specific lists but not yet added to the global
device list.  Make sure the pci remove functions can handle this case.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a pci child bus is created, add it to the parent's children list
immediately rather than waiting till pci_bus_add_devices().  For hot-plug
bridges/devices, pci_bus_add_devices() may be called much later, after they
have been properly configured.  In the meantime, this allows us to use the
normal pci bus search functions for the hot-plug bridges/buses.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

With root bridge and pci bridge hot-plug, new buses and devices can be added
or removed at run time.  Protect the pci bus and device lists with the pci
lock when doing so.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When hot-plugging a root bridge, as we try to assign bus numbers we may find
that the hotplugged hieratchy has more PCI to PCI bridges (i.e.  bus
requirements) than available.  Make sure we don't step over an existing bus
when that happens.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

PCI scan code calls the arch specific pcibios_fixup_bus() each time it scans a
new bridge.  For root bridge hot-plug, the bridge and it's attached devices
may not have been configured properly yet, so it's not safe to claim those
resources at this time.

This code goes away when we clean up the way pci resources are claimed (in
pci_enable_device()), so this is only a stopgap fix.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When checking if a PCI to PCI bridge should be enabled to decode memory and/or
IO resources, we need to look at all device resources not just the first 6.
This is needed to allow PCI bridges to pass down memory and IO accesses to
child devices even when the bridge itself does not consume resources in its
PCI BARs.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When you hot-plug a (root) bridge hierarchy, it may have p2p bridges and
devices attached to it that have not been configured by firmware.  In this
case, we need to configure the devices before starting them.  This patch
separates device start from device scan so that we can introduce the
configuration step in the middle.

I kept the existing semantics for pci_scan_bus() since there are a huge number
of callers to that function.

Also, I have no way of testing the changes I made to the parisc files, so this
needs review by those folks.  Sorry for the massive cross-post, this touches
files in many different places.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replace pci_find_device() with more safer pci_get_device().
Signed-off-by: NAmit Gud <gud@eth.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replace pci_find_device() with more safer pci_get_device().
Signed-off-by: NAmit Gud <gud@eth.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I updated this to remove unnecessary variable initialization, make
check_routing be inline only and not __init, switch to strtoul, and
formatting fixes as per Randy Dunlap's recommendations.

I updated this to change pirq_table_addr to a long, and to add a warning
msg if the PIRQ table wasn't found at the specified address, as per thread
with Matthew Wilcox.

In our hardware situation, the BIOS is unable to store or generate it's PIRQ
table in the F0000h-100000h standard range. This patch adds a pci kernel
parameter, pirqaddr to allow the bootloader (or BIOS based loader) to inform
the kernel where the PIRQ table got stored. A beneficial side-effect is that,
if one's BIOS uses a static address each time for it's PIRQ table, then
pirqaddr can be used to avoid the $pirq search through that address block each
time at boot for normal PIRQ BIOSes.
Signed-off-by: NJaya Kumar <jayalk@intworks.biz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

From: <pageexec@freemail.hu>

$subject was fixed in 2.4 already, 2.6 needs it as well.

The impact of the bugs is a kernel stack overflow and privilege escalation
from CAP_NET_ADMIN via the IP_VS_SO_SET_STARTDAEMON/IP_VS_SO_GET_DAEMON
ioctls.  People running with 'root=all caps' (i.e., most users) are not
really affected (there's nothing to escalate), but SELinux and similar
users should take it seriously if they grant CAP_NET_ADMIN to other users.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes two bugs in the dm9000 network driver:

- Don't read one byte too much in 8bit mode.
- release correct resource
Signed-off-by: NJochen Karrer <j.karrer@lightmaze.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

Patch indents dmfe.txt to look like other docs.  It adds a tip about CNET
cards using Davicom chipsets.  Also it removes parts where it refers to how
to build driver out-of-kernel which seems to be cruft from times where the
driver was out of the kernel.
Signed-off-by: NIsmail Donmez <ismail@kde.org.tr>
Signed-off-by: NDomen Puncer <domen@coderock.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

Signed-off-by: NAndrew Morton <akpm@osdl.org>

Fix int vs. pm_message_t confusion in airo. Should change no code.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

This is a fix for the interrupt handler in the defxx driver to use
irqreturn_t.  Beside the obvious fix of returning a proper status at all,
it actually checks board registers as appropriate for determining if an
interrupt has been recorded in the bus-specific interface logic.

The patch also includes an obvious one-line fix for SET_NETDEV_DEV needed
for the EISA variation, for which I've decided there is no point in sending
separately.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

drivers/net/tulip/dmfe.c: In function `dmfe_parse_srom':
drivers/net/tulip/dmfe.c:1805: warning: passing arg 1 of `__le16_to_cpup' from incompatible pointer type
drivers/net/tulip/dmfe.c:1817: warning: passing arg 1 of `__le32_to_cpup' from incompatible pointer type
drivers/net/tulip/dmfe.c:1817: warning: passing arg 1 of `__le32_to_cpup' from incompatible pointer type

This is basically a guess:

Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

The 8129/8130 support is a sub-option that is not visible if the user
hasn't enabled the 8139 support.

Let's make it a bit easier for users to find the driver for their nic.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

1) netlink_release() should only decrement the hash entry
   count if the socket was actually hashed.

   This was causing hash->entries to underflow, which
   resulting in all kinds of troubles.

   On 64-bit systems, this would cause the following
   conditional to erroneously trigger:

	err = -ENOMEM;
	if (BITS_PER_LONG > 32 && unlikely(hash->entries >= UINT_MAX))
		goto err;

2) netlink_autobind() needs to propagate the error return from
   netlink_insert().  Otherwise, callers will not see the error
   as they should and thus try to operate on a socket with a zero pid,
   which is very bad.

   However, it should not propagate -EBUSY.  If two threads race
   to autobind the socket, that is fine.  This is consistent with the
   autobind behavior in other protocols.

   So bug #1 above, combined with this one, resulted in hangs
   on netlink_sendmsg() calls to the rtnetlink socket.  We'd try
   to do the user sendmsg() with the socket's pid set to zero,
   later we do a socket lookup using that pid (via the value we
   stashed away in NETLINK_CB(skb).pid), but that won't give us the
   user socket, it will give us the rtnetlink socket.  So when we
   try to wake up the receive queue, we dive back into rtnetlink_rcv()
   which tries to recursively take the rtnetlink semaphore.

Thanks to Jakub Jelink for providing backtraces.  Also, thanks to
Herbert Xu for supplying debugging patches to help track this down,
and also finding a mistake in an earlier version of this fix.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use msleep_interruptible() instead of schedule_timeout() to guarantee
the task delays as expected.

This patch removes some obviously dead code found by the Coverity
checker.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

This patch fixes the LITTLE_ENDIAN #define and a function prototype.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

This patch contains the follwing cleanups:
- make needlessly global code static
- remove obsolete Emacs settings
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

We're using __be16 in userland visible types, so we
have to include asm/byteorder.h so that works.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRobert Olsson <robert.olsson@its.uu.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During some performance diagnostics I stumbled on this slightly wasteful
code in pcnet_cs.c which I made the patch included at the bottom for (two
minor comment fixes included).

Improvement:
instead of *always* calculating
lea    0x2c0(%edx),%ebx
and then additionally doing the
mov    %edx,0xc0(%ebx)
addition *if we need it*,

we now do the *whole* calculation of
mov    %edx,0x380(%ebx)
*only* if we need it.
This even manages to save us a whole 16-byte alignment buffer loss
in this compilation case.

Result: slightly improves IRQ handler performance in both shared and
non-shared IRQ case, which should make my rusty P3/700 a slight bit happier.

Thank you for your support,

Andreas Mohr

old asm result (using gcc 3.3.5):

000015a0 <ei_irq_wrapper>:
    15a0:       55                      push   %ebp
    15a1:       89 e5                   mov    %esp,%ebp
    15a3:       53                      push   %ebx
    15a4:       8d 9a c0 02 00 00       lea    0x2c0(%edx),%ebx
    15aa:       e8 fc ff ff ff          call   15ab <ei_irq_wrapper+0xb>
    15af:       83 f8 01                cmp    $0x1,%eax
    15b2:       74 03                   je     15b7 <ei_irq_wrapper+0x17>
    15b4:       5b                      pop    %ebx
    15b5:       5d                      pop    %ebp
    15b6:       c3                      ret
    15b7:       31 d2                   xor    %edx,%edx
    15b9:       89 93 c0 00 00 00       mov    %edx,0xc0(%ebx)
    15bf:       eb f3                   jmp    15b4 <ei_irq_wrapper+0x14>
    15c1:       eb 0d                   jmp    15d0 <ei_watchdog>
    15c3:       90                      nop
    15c4:       90                      nop
    15c5:       90                      nop
    15c6:       90                      nop
    15c7:       90                      nop
    15c8:       90                      nop
    15c9:       90                      nop
    15ca:       90                      nop
    15cb:       90                      nop
    15cc:       90                      nop
    15cd:       90                      nop
    15ce:       90                      nop
    15cf:       90                      nop

000015d0 <ei_watchdog>:

new asm result:

000015a0 <ei_irq_wrapper>:
    15a0:       55                      push   %ebp
    15a1:       89 e5                   mov    %esp,%ebp
    15a3:       53                      push   %ebx
    15a4:       89 d3                   mov    %edx,%ebx
    15a6:       e8 fc ff ff ff          call   15a7 <ei_irq_wrapper+0x7>
    15ab:       83 f8 01                cmp    $0x1,%eax
    15ae:       74 03                   je     15b3 <ei_irq_wrapper+0x13>
    15b0:       5b                      pop    %ebx
    15b1:       5d                      pop    %ebp
    15b2:       c3                      ret
    15b3:       31 d2                   xor    %edx,%edx
    15b5:       89 93 80 03 00 00       mov    %edx,0x380(%ebx)
    15bb:       eb f3                   jmp    15b0 <ei_irq_wrapper+0x10>
    15bd:       8d 76 00                lea    0x0(%esi),%esi

000015c0 <ei_watchdog>:
Signed-off-by: NAndrew Morton <akpm@osdl.org>

Use the DMA_{64,32}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()

This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.

See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: NTobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: NDomen Puncer <domen@coderock.org>

It doesn't seem to make much sense to let an "If unsure, say N." option 
default to y.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since it is tristate when we offer it as a choice, we should
definte it also as tristate when forcing it as the default.
Otherwise kconfig warns.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure the code compiles with and without ARLAN_ENTRY_EXIT_DEBUGGING.
Only provide parameter descriptions when parameters are defined.
Remove "arlan_"-prefix to shape up built-in parameter names:

arlan.arlan_debug -> arlan.debug
arlan.arlan_EEPROM_bad -> arlan.EEPROM_bad
arlan.arlan_entry_and_exit_debug -> arlan.entry_and_exit_debug
arlan.arlan_entry_debug -> arlan.entry_debug
arlan.arlan_exit_debug -> arlan.exit_debug
Signed-off-by: NMagnus Damm <damm@opensource.se>

Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask() instead of custom
macros.
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: NTobias Klauser <tklauser@nuerscht.ch>